Design for Delay Fault Testability of 2-Rail Logic Circuits

スポンサーリンク

概要

• 論文の詳細を見る

• This paper presents a scan design for delay fault testability of 2-rail logic circuits. The flip flops used in the scan design are based on master-slave ones. The proposed scan design provides complete fault coverage in delay fault testing of 2-rail logic circuits. In two-pattern testing with the proposed scan design, initial vectors are set using the set-reset operation, and the scan-in operation for initial vectors is not required. Hence, the test application time is reduced to about half that of the enhanced scan design. Because the additional function is only the set-reset operation of the slave latch, the area overhead is small. The evaluation shows that the differences in the area overhead of the proposed scan design from those of the standard scan design and the enhanced scan design are 2.1 and -14.5 percent on average, respectively.

• （社）電子情報通信学会の論文
• 2009-02-01

著者

• Namba Kazuteru

  Chiba Univ. Chiba‐shi Jpn

• NAMBA Kazuteru

  Graduate School of Advanced Integration Science, Chiba University

• ITO Hideo

  Graduate School of Advanced Integration Science, Chiba University

• KATOH Kentaroh

  Graduate School of Science and Technology, Chiba University

• Ito Hideo

  Chiba Univ. Chiba‐shi Jpn

• Katoh Kentaroh

  Graduate School Of Science And Technology Chiba University

• Namba Kazuteru

  Graduate School Of Advanced Integration Science Chiba University

• Ito Hideo

  Graduate School Of Advanced Integration Science Chiba University

• Ito Hideo

  Graduate School Of Advanced Integration Sci. Chiba Univ.

• Namba Kazuteru

  Graduate School Of Advanced Integration Sci. Chiba Univ.

関連論文

• Test Compression for Robust Testable Path Delay Fault Testing Using Interleaving and Statistical Coding
• Analysis of Path Delay Fault Testability for Two-Rail Logic Circuits
• Design for Delay Fault Testability of 2-Rail Logic Circuits
• Design for Delay Fault Testability of Dual Circuits Using Master and Slave Scan Paths
• BILBO FF with soft error correcting capability (コンピュータシステム)
• BILBO FF with soft error correcting capability (ディペンダブルコンピューティング)
• Test Compression for Robust Testable Path Delay Fault Testing Using Interleaving and Statistical Coding
• Design for Delay Fault Testability of Dual Circuits Using Master and Slave Scan Paths
• Design for Delay Fault Testability of 2-Rail Logic Circuits
• X-Tolerant Test Data Compression for SOC with Enhanced Diagnosis Capability(Dependable Computing)
• Single-Event-Upset Tolerant RS Flip-Flop with Small Area
• Parallel Decoding for Burst Error Control Codes
• Two-Level Unequal Error Protection Codes with Burst and Bit Error Correcting Capabilities
• A Checkpointing Method with Small Checkpoint Latency
• Low-Cost IP Core Test Using Tri-Template-Based Codes
• Construction of BILBO FF with Soft-Error-Tolerant Capability
• Deterministic Delay Fault BIST Using Adjacency Test Pattern Generation(Dependable Computing)
• Construction of Soft-Error-Tolerant FF with Wide Error Pulse Detecting Capability
• Analysis of Path Delay Fault Testability for Two-Rail Logic Circuits
• A Dynamically Configurable NoC Test Access Mechanism
• A Dynamically Configurable NoC Test Access Mechanism (VLSI設計技術)
• A Dynamically Configurable NoC Test Access Mechanism
• A Dynamically Configurable NoC Test Access Mechanism
• Unequal Error Control Codes with Two-Level Burst and Bit Error Correcting Capabilities
• Design for Delay Measurement Aimed at Detecting Small Delay Defects on Global Routing Resources in FPGA
• Improving Test Coverage by Measuring Path Delay Time Including Transmission Time of FF
• Two-Stage Stuck-at Fault Test Data Compression Using Scan Flip-Flops with Delay Fault Testability

もっと見る 閉じる

スポンサーリンク