Interface Structure and Strength of Si_3N_4/Si_3N_4 Joints Brazed with Ni-Si-Ti Filler Metals(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
スポンサーリンク
概要
- 論文の詳細を見る
Si_3N_4 was brazed to Si_3N_4 using Ni-20Si xTi Filler Metals in vacuum, where x changed from 0 to 15 at%. The wettability of the alloys against Si_3N_4 was evaluated by the sessile drop method. The contact angle of the alloys at 3.6ks decreases effectively with increasing Ti content up to 10 at% from 130 degree for Ni-20Si to 22 degree for Ni-20Si-10Ti. The further addition of Ti content of 10 at% or more increases the contact angle to 48 degree for Ti content of 15 at%. Ni-20Si-10Ti alloy exhibited the best wettability among the alloys against Si_3N_4. The strength of Si_3N_4/Si_3N_4 joint brazed with the alloys showed the highest value of 243MPa. The alloys which exhibit good wettability possess the highest bonding strength against Si_3N_4.
- 大阪大学の論文
著者
関連論文
- Wetting of Silicon Carbide by Copper-Titanium Alloys(Physics, Process, Instrument & Measurement)
- High Rate Sputtering of Corrosion-Resistant Alloys(Welding Physics, Processes & Instruments)
- Solid State Diffusion Bonding of Silicon Nitride with Vanadium Foils(Materials, Metallurgy & Weldability)
- Interfacial Microstructure of Solid State Diffusion Bonded Silicon Nitride using Niobium Foils(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Ultrasonic Brazing of Alumina to Copper Using Zn-Al Filler(Materials, Metallurgy & Weldability)
- Influence of Brazing Condition on Shear Strength of Alumina-Kovar Joint Made with Amorphous Cu_Ti_ Filler Metal
- Corrosion Behavior of Amorphous Fe-Cr-Zr Alloys
- Effect of Chromium Addition on Corrosion Resistance of Amorphous Co-Zr Alloys
- Reaction and Structure at the Solid State Diffusion Bonded Ti/Si_3N_4 Interface(Materials, Metallurgy & Weldability)
- Laser Metallization of Ceramics
- Heat-Resistant Brazing of Ceramics (Report I) : Brazing of SiC Using Ni-Ti Filler Metals(Physics, Process, Instrument & Measurement)
- Amorphous Alloy and Its Application to Joining
- Joining of Alumina to Copper Using Amorphous Cu-Ti Filler Metal(Materials, Metallurgy & Weldability)
- Joining of Al_2O_3 to SUS 304 with Ti Foil
- Wetting of Zirconia by Cu-Zr Alloys
- Interfacial Structure and Bond Strength of Solid State Bonded SiC/Ni Joints(Materials, Metallurgy & Weldability)
- Effect of Sn Addition to Cu-Ti Filler Metals on Microstructure and Strength of SiC/SiC Joint(Materials, Metallurgy & Weldability)
- Interfacial Microstructure and Reaction Phases in Si_3N_4/Si_3N_4 Joints Brazed with Cu-Zn-Ti Filler Alloy(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- 408 REACTION SYNTHESIS OF NiAl-TiC COMPOSITES AND IN-SITU JOINING TO Ni_3Al ALLOYS
- High Temperature Reactions of Ti with SiC(Materials, Metallurgy & Weldability)
- Interfacial Structure and Reaction Mechanism of SiC/Nb Joints(Materials, Metallurgy & Weldability)
- Brazing of Si_3N_4 to Metals with Al-Cu Filler Metals(Physics, Process, Instrument & Measurement)
- Brazing of Si_3N_4 to Metals with Al Filler (Report II) : Si_3N_4/Fe, Ni, Cu, Al or SUS304 Joint(Physics, Process, Instrument & Measurement)
- Brazing of Si_3N_4 to Metals with Al Filler (Report I) : Si_3N_4/Si_3N_4 and Si_3N_4/Ti or Nb Joints(Materials, Metallurgy & Weldability)
- Intermediary Layer of Titanium Oxide in Al_2O_3/Cu Joint Using Amorphous Cu-Ti Filler Metals
- Formation of Hercynite (FeAl_2O_4) at Interface of Al_2O_3/Steel Joint
- Thermal Stability of Microstrucuture and Microhardness in Nanostructured Ni-Cr Alloy Foils Prepared by RF Sputtering Method(Materials, Metallurgy & Weldability)
- Interfacial Reaction between Titanium and Silicon Nitride during Solid State Diffusion Bonding(Materials, Metallurgy & Weldability)
- Interface Layer Structure of Solid State Bonded SiC/TiAl Joint(Materials, Metallurgy & Weldability)
- Mechanical Properties of Nanostructured Cr-B Films Produced by RF Sputtering(Materials, Metallurgy & Weldability)
- Synthesis of β-FeSi_2 Utilizing the Combined Process of MA/SPS(Materials, Metallurgy & Weldability)
- Joining of Silicon Nitride Using Amorphous Cu-Ti Filler Metal(Materials, Metallurgy & Weldability)
- Joining of SiC Using Amorphous Ti Base Filler Metal(Materials, Metallurgy & Weldability)
- Joining of Silicon Nitride to Metals or Alloys Using Amorphous Cu-Ti Filler Metal(Materials, Metallurgy & Weldability)
- Non-oxide Ceramics (Si_3N_4, SiC) Joint Made with Amorphous Cu_Ti_ and Ni_Ti_ Filler Metals
- Development of Cu-Sn or Cu-Zn Filler Metal for Joining Ceramics(Materials, Metallurgy & Weldability)
- Interface Structure and Strength of Si_3N_4/Si_3N_4 Joints Brazed with Ni-Si-Ti Filler Metals(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Bonding Behavior between Niobium and Reaction-Sintered SiC(Materials, Metallurgy & Weldability)
- Controlling of Ceramic-Metal Interfacial Structure Using Molten Metals
- Ultrasonic Brazing of Alumina to Copper Using Zn-Al-Cu Fillers(Materials, Metallugy & Weldability)
- Coating of High Corrosion Resistant Amorphous Stainless Steels by RF Sputtering(Materials, Metallurgy & Weldability)
- Ultrasonic Soldering of Alumina to Copper Using Sn-Pb Solders(Materials, Metallurgy & Weldability)
- Joining Ability of Al-Base Filler Metals against Al_2O_3(Materials, Metallurgy & Weldability)
- Application of Ultrasonic Waves during Brazing of Alumina/Copper Using Zn-Sn Filler(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Formation of Corrosion Resistant Amorphous Ti-B Alloys(Materials, Metallurgy & Weldability)
- Electron Back-Scatter Pattern Analyses of a Recrystallized Al-4mass%Mg Alloy Sheet(Materials, Metallurgy & Weldability)
- Fabrication and Applications of Rapidly Quenched Metals
- Impact Welding of Aluminum onto Copper by the Gas-Gun Method(Materials, Metallurgy & Weldability)
- Joining of Advanced Materials by Combustion Synthesis
- Wetting of Alumina by Molten Aluminum and Aluminum-Copper Alloys(Welding Physics, Process & Instrument)
- Joining Al_2O_3 to Al_2O_3 by Brazing
- Wetting of Silicon Nitride by Copper-Titanium or Copper-Zirconium Alloys(Welding Physics, Process & Instrument)
- Interfacial Phenomena and Bond Strength in Joining AlN Ceramics Using Metals Foils(Materials, Metallurgy & Weldability)
- Brazeability of Ni-Sn-Ti Filler Metals against Si_3N_4(Materials, Metallurgy & Weldability)
- Mechanism of Ultrasonic Irradiation on Joining of Alumina/Copper(Materials, Metallurgy & Weldability)
- Statistical Analysis of Alumina/Metal Brazed Joints under Applying of Ultrasonic Waves(Materials, Metallurgy & Weldability)
- Kinetics of Growth of Reaction Phases at Ceramic/Metal Interfaces
- The Crystallization Kinetics of Glassy Fe_ Ni_ P_