Austenitic Grain Growth behavior Immediately after Dynamic Recrystallization in HSLA Steels and Austenitic Stainless Steel

スポンサーリンク

概要

• 論文の詳細を見る

• Austenitic grain growth behavior after dynamic recrystallization in HSLA steels and the austenitic stainless steel of Type 316L was investigated focusing on grain growth during a very short holding time period immediately after hot deformation. Hot compressed specimens were isothermally held at temperatures of 1373 K, 1423 K and 1473 K for various time periods from 0.1 s to 1.8 ks. The grain size in all steels was coarsened by 1.5 to 2.5 times in a short holding time period of 20 s. Addition of 0.078%Zr or 0.018%Ti in HSLA steel could not prevent this rapid grain growth, which retarded grain growth in a longer holding time period over 60 s. The grain growth exponent of the n value was evaluated using a formulated grain growth kinetic equation, and two n values largely differing in the fine and coarse grain size regions were obtained in a respective temperature and alloy. The n value in the latter region ranged from 2.3 to 3.2, being almost consistent with values of various materials reported in the past studies. The very high n value over 7.7 was obtained in the fine grain size region for dynamic recrystallization in all steels, where n values for static recrystallization was relatively lower than those for dynamic recrystallization. The similar result of n values was obtained from grain growth data after dynamic recrystallization in pure nickel. The cause for very high n value and the difference of n values obtained from grain growth data after dynamic and static recrystallizations were discussed based on features of the microstructure and the grain boundary evolved by dynamic or static recrystallization and annealing.

• 社団法人 日本鉄鋼協会の論文
• 2008-10-15

著者

• NARUSHIMA Takayuki

  Department of Materials Processing, Tohoku University

• 成島 尚之

  Department Of Materials Processing Tohoku University

• OUCHI Chiaki

  Department of Materials Processing, Tohoku University

• Ouchi C

  Department Of Materials Processing Tohoku University

• Ouchi Chiaki

  Tohoku University

• SAHARA Ryoji

  Department of Materials Processing, Tohoku University

• Narushima Takayuki

  Department Of Materials Processing Graduate School Of Engineering Tohoku University

• Sahara Ryouji

  Department Of Materials Processing Tohoku University

• Sahara Ryoji

  Institute For Materials Research Tohoku University

• Ouchi Chiaki

  Department Of Metallurgy Tohoku University

• Fujita Noriki

  Department Of Metallurgy Graduate School Of Engineering Tohoku University

• Nezu Takashi

  Department Of Dental Materials Science And Technology Iwate Medical University School Of Dentistry

• FUJITA Noriki

  Tohoku University

• Ouchi Chiaki

  Department Of Materials Processing Graduate School Of Engineering Tohoku University

関連論文

• Apatite formation behavior on bio-ceramic films prepared by MOCVD
• Precipitation Behavior in a Hanks' Solution on Ca-P-O Films Prepared by Laser CVD
• Calcium Phosphate Films with/without Heat Treatments Fabricated Using RF Magnetron Sputtering
• Hydroxyapatite Formation on Ca-P-O Coating Prepared by MOCVD
• MOCVD法によるCa-Ti-OおよびCa-P-O系傾斜機能バイオセラミックス膜の合成
• ブラスト処理を施したTi-6Al-4V合金基板へのリン酸カルシウムコーティングと生体内外評価
• Hydroxyapatite Formation on CaTiO_3 Film Prepared by Metal-Organic Chemical Vapor Deposition
• Evaluation of Calcium Phosphate Coating Films on Titanium Fabricated Using RF Magnetron Sputtering
• Precipitation Behavior in a Hanks' Solution on Ca-P-O Films Prepared by Laser CVD
• S111 CVD法により合成したCa-P-O膜の骨形成に及ぼす微細組織の影響(力学適応能,自己組織化能を有するバイオマテリアル-生体インターフェイスの創製,SP1:シンポジウム1)
• S109 ブラスト処理Ti-6Al-4V基板へのリン酸カルシウムコーティングと生体内外評価(力学適応能,自己組織化能を有するバイオマテリアル-生体インターフェイスの創製,SP1:シンポジウム1)
• Surface Hardening Treatment for Titanium Materials Using Ar-5%CO Gas in Combination with Post Heat Treatment under Vacuum
• チタン上への多層リン酸カルシウムコーティング膜の作製とその評価
• P20.PMA誘導したTHP-1細胞(マクロファージ)によるチタン微小粉の貪食の評価(一般演題抄録,第5回日本再生歯科学会)
• CO_2ガスを利用したチタンおよびチタン合金の表面硬化処理(加工・加工熱処理)
• TiB及びY_2O_3分散粒子による粉末冶金チタン合金のβ粒微細化
• Boron and Nitrogen in GaAs and InP Melts Equilibrated with B_2O_3 Flux
• Behavior of Oxygen in Ga-As Melts with the Range of As Content up to 5 mass % Equilibrated with B_2O_3 Flux
• Activity of Ga_2O_3 in B_2O_3 Flux and Standard Free Energies of Formation of CaBO_3 and InBO_3
• Alkali Hydrothermal Synthesis of Zeolite A Using Oxide By-products
• J0401-2-3 チタン基板上に作製したリン酸カルシウムコーティング膜評価(生体材料およびその表面改質材(2))
• Dynamic and Static Restoration Behaviors of Pure Lead and Tin in the Ambient Temperature Range
• Viscoelastic behavior of commercially available tissue conditioners under compression
• The Effect of Solute Elements on Hardness and Grain Size in Platinum Based Binary Alloys
• Development of a New Method for Manufacturing Iron Foam Using Gases Generated by Reduction of Iron Oxide
• Hydrothermal Synthesis of Zeolite A Using Blast Furnace Slag
• 真空後熱処理を組み合わせたAr-5%COガスを利用したチタン材料の表面硬化処理法
• チタン合金のβ粒微細化及び粒成長挙動に及ぼすY_2O_3分散粒子の影響
• 極微量のイットリウム添加α+β型チタン合金のβ粒成長に及ぼす加熱温度・時間の影響
• 鉄鋼スラグ及び結晶性Al_2O_3を原料としたゼオライトAのアルカリ水熱合成
• 鋳造低合金鋼での動的再結晶後のγ粒成長挙動に及ぼす微量元素の影響
• 動的再結晶による鋼の凝固オーステナイト粒の微細化及び粒成長挙動
• The Effects of the Oxygen-enriched Surface Layer on Mechanical Properties of α+β Type Titanium Alloys
• 連続鋳造による9%Ni鋼のミクロ偏析に及ぼすオーステナイトでの動的再結晶の影響
• Development of Steel Plates by Intensive Use of TMCP and Direct Quenching Processes
• Fatigue Behaviors of Ultra Fine Wires of β-Type and α-Type Titanium Alloys
• Oxidation or Nitridation Behavior of Pure Chromium and Chromium Alloys Containing 10mass%Ni or Fe in Atmospheric Heating
• Alloy Design and Property Evaluation of New β Type Titanium Alloy with Excellent Cold Workability and Biocompatibility
• Preparation of Calcium Phosphate Films by Radiofrequency Magnetron Sputtering
• Grain Refinement of As Cast Austenite by Dynamic Recrystallization in HSLA Steels
• Solubilities and Equilibrium Distribution Coefficients of Oxygen and Carbon in Silicon
• 鉄鋼スラグを原料としたぜオライト類のアルカリ水熱合成
• 生体用チタンおよびチタン合金 (特集 金属系バイオマテリアルの研究開発・最前線)
• Deoxidation of NiTi Alloy Melts Using Metallic Barium
• PREFACE
• Special Issue on New Functions and Properties of Engineering Materials Created by Designing and Processing
• PREFACE
• Special Issue on Medical, Healthcare, Sport and Leisure Materials
• Thermodynamic Properties of Transition Metals Using Face-Centered-Cubic Lattice Model with Renormalized Potentials
• Weak Universality of a Site-Percolation Model With Two Different Sizes of Particles on a Square Lattice
• Site-Percolation Models Including Heterogeneous Particles on a Square Lattice
• Monte Carlo Simulation of Cu-Au Alloys on FCC Iattice with a Renormalized Potential
• Hardness and Composition of Solution-Treated Ag-Pd-Cu-Au Alloy Microstructures
• TEM/EDX Observation of Micro-beads of Magnetically Activated Cell Sorting (MACS) System and Separation Trial of Mouse Mesenchymal Stem Cells from Bone Marrow Cells by MACS System
• Effect of pH and Addition of Salt on the Adsorption Behavior of Lysozyme on Gold, Silica, and Titania Surfaces Observed by Quartz Crystal Microbalance with Dissipation Monitoring
• Gene Expression Analyses of Human Mesenchymal Stem Cells Cultured in Osteogenic Differentiation Medium for 3, 7, 14 and 21 Days by Genome Focus DNA Microarray and Real-time PCR
• New Index for the Stability of a Type I Collagen Affected by Hydrophobic Environment
• Preparation of Highly Pore-interconnected Porous Collagen Sponges using Chloroform and Ammonia
• Accumulation of Element Ti in Macrophage-like RAW264 Cells Cultured in Medium with 1 ppm Ti and Effects on Cell Viability, SOD Production and TNF-α Secretion
• DNA Microarray Analyses of Gene Expression in Human Mesenchymal Stem Cells Cultured in Osteogenic Differentiation Medium for 14 days
• Fatigue Properties of Stainless Steel Wire Ropes for Electrodes in Functional Electrical Stimulation Systems
• P-61 PIXE法による細胞培養液とチタンイオン貪食マクロファージRAW264の元素分析(細胞,一般講演(ポスター発表),第47回日本歯科理工学会学術講演会・総会)
• チタンイオンがマクロファージ様細胞RAW264の細胞生存率に及ぼす影響評価(毒性, 平成17年度秋期 (長崎) 第46回日本歯科理工学会学術講演会)
• 超微細組織を有する生体用新α+β型チタン合金の熱処理特性
• Alloy Design and Properties of New α+β Titanium Alloy with Excellent Cold Workability, Superplasticity and Cytocompatibility
• Oxygen Distribution in Titanium Single Crystal Fabricated by Optical Floating-Zone Method under Extremely Low Oxygen Partial Pressure
• Evaluation of Sliding Wear Resistant Property of C. P. Titanium and SP-700 Titanium Alloy Surface-hardened by Ar-5%CO Gas
• Variations in the Microstructure and Hardness with Solution Treating and Aging Conditions in New α+β Titanium Alloy Ti-4.5%Al-6%Nb-2%Fe-2%Mo
• β Grain Refinement due to Small Amounts of Yttrium Addition in α+β Type Titanium Alloy, SP-700
• Austenitic Grain Growth behavior Immediately after Dynamic Recrystallization in HSLA Steels and Austenitic Stainless Steel
• Surface Hardening Treatment for C.P. Titanium and Titanium Alloys in Use of Ar-5%CO Gas
• Effects of Dynamic Recrystallization on γ Grain Refinement and Improvement of Micro Segregation of As Cast Austenite in 9%Ni Steel
• Strength-Ductility Relationship in Solution Treated and Aged α+β Type Ti-4.5%Al-3%V-2%Fe-2%Mo Titanium Alloy
• Origin of the Blue Shift in Ultraviolet Absorption Spectra of Nanocrystalline CeO_ Particles
• Controlling the Percolation Threshold of Conductor-Insulator Composites by Changing the Granular Size of Insulators
• Conductivity Percolation on a Square Lattice with Core-Shell Particles
• Conductivity Percolation on a Square Lattice with Two Different Sizes of Particles
• Effect of HEMA Adsorption on the Stability of Native and Denatured Type I Tendon Collagen
• Effect of β Phase Stability at Room Temperature on Mechanical Properties in β-Rich α+β Type Ti-4.5Al-3V-2Mo-2Fe Alloy
• Determination of Free Lime Contents in Slags by Solution Calorimetry
• Effect of Alloying Elements on Carbon Solubility in Liquid Silicon Equilibrated with Silicon Carbide
• Conductivity Percolation on a Cubic Lattice with Two Different Sizes of Particles
• S0201-1-2 熱酸化プロセスを利用したチタン上へのアナターゼ皮膜形成と骨適合性評価(骨再生と骨再建のためのバイオマテリアル(1),社会変革を技術で廻す機械工学)
• Effect of Al on ω phase transformation behavior in Ti-8V-5Fe-(1-3)Al alloy
• Effect of Cooling Rate on Microstructure and Fracture Characteristics of β-Rich α+β Type Ti-4.5Al-3V-2Mo-2Fe Alloy
• Conductivity Percolation on a Cubic Lattice with Core-Shell Particles
• Alkali Hydrothermal Synthesis of Zeolite A Using Oxide By-products
• Oxidation of Boron Carbide-Silicon Carbide Composite at 1073 to 1773K
• Oxidation of Boron Carbide-Silicon Carbide Composite at 1073 to 1773K
• Proteome analyses of human macrophages exposed to low cytotoxic IC90 copper (2+) ions
• Evolution of Solidification Structures in Fe-Mn-Si-Cr Shape Memory Alloy in Centrifugal Casting
• First-Principles Calculations on $\Sigma 3$ Grain Boundary Transition Metal Impurities in Multicrystalline Silicon
• Controlling 3D Percolation Threshold of Conductor-Insulator Composites by Changing the Granular Size of Conductors
• Recovery of Calcium from BF Slag and Synthesis of Zeolite A Using Its Residue
• Controlling the Percolation Threshold of Conductor-Insulator Composites in a 2D Triangular Lattice by Introducing Binary Size Distributions of Conductor Particles
• Biomechanical Evaluation of Amorphous Calcium Phosphate Coated TNTZ Implants Prepared Using a Radiofrequency Magnetron Sputtering System
• 生体材料としてのチタンおよびチタン合金
• チタン, チタン合金
• β-Grain Refinement of α+β-Type Ti-4.5Al-6Nb-2Fe-2Mo Alloy by Using Rare-Earth-Oxide Precipitates
• Formation of Anatase on Commercially Pure Ti by Two-Step Thermal Oxidation Using N_2-CO Gas

もっと見る 閉じる

スポンサーリンク