Physical and Chemical Characterization of Reused Oxide Chemical Mechanical Planarization Slurry

スポンサーリンク

概要

• 論文の詳細を見る

• The recycle of Chemical Mechanical Planarization (CMP) slurries has been actively considered in the industry to reduce the cost-of-consumables (COC) because of the sharp increase of the consumption of slurry in CMP@. The main purpose of this study was to characterize the used oxide slurry physically and chemically to establish a means of reprocessing it. The characteristics of slurry were determined according to pH, solid content, specific gravity and particle size. These characteristics were affected and varied by deionized water inflow during the CMP process. The tetraethylorthosilicate removal rate was strongly dependent on the solid content and pH of slurry solutions. The solid content played a major role in determining the removal rates. Regardless of the number of polishings, the removal rate was almost the same at a solid content when it was modified by adding new slurry. The mean particle size of slurries did not change at all even in the five times recycled slurry. Even though there was a slight increase in the fraction of large particles in the range of 20 to 120 $\mu$m in the recycled slurries, no changes in thickness uniformity or defect density were observed when polishing was performed in either new or recycled slurry.

• Publication Office, Japanese Journal of Applied Physics, Faculty of Science, University of Tokyoの論文
• 2001-03-15

著者

• Park Jin-goo

  Department Of Metallurgy And Materials Engineering Center For Electronic Materials And Components Ha

• Kim Hyung-joon

  Department Of Metallurgy And Materials Engineering Center For Electronic Materials And Components Ha

• Kim Hyung-Joon

  Department of Metallurgy and Materials Engineering, Center for Electronic Materials and Components, Hanyang University, Ansan, 425-791, Korea

• Eom Dae-Hong

  Department of Materials Engineering, Hanyang University, Ansan 426-791, Korea

• Park Jin-Goo

  Department of Bio-Nano Technology and Micro Biochip Center, Hanyang University, Ansan 426-791, Korea

関連論文

• Effect of a Guard-Ring on the Leakage Current in a Si-PIN X-Ray Detector for a Single Photon Counting Sensor
• Effect of a guard-ring on the leakage current in a Si-PIN x-ray detector for a single photon counting sensor (Electron devices: 第15回先端半導体デバイスの基礎と応用に関するアジア・太平洋ワークショップ(AWAD2007))
• Effect of a guard-ring on the leakage current in a Si-PIN x-ray detector for a single photon counting sensor (Silicon devices and materials: 第15回先端半導体デバイスの基礎と応用に関するアジア・太平洋ワークショップ(AWAD2007))
• Reaction of Ozone and H_2O_2 in NH_4OH Solutions and Their Reaction with Silicon Wafers
• Point of Use Regeneration of Oxide Chemical Mechanical Planarization Slurry by Filtrations
• Effect of Chemicals and Slurry Particles on Chemical Mechamical Polishing of Polyimide
• Particle Removal and Its Mechanism on Hydrophobic Silicon Wafer in Highly Diluted NH_4OH Solutions with an Added Surfactant : Semiconductors
• Effect of Organic Acids in Copper Chemical Mechanical Planarization Slurry on Slurry Stability and Particle Contamination on Copper Surfaces
• Passivation and Etching of Wafer Surfaces in HF-H_2O_2-WA Solutions
• The Hydrophilization of Process Wafers in Dilute Hydrogen Peroxide Solutions and Ozonated Deionized Water and Its Effects on Defects and Gate Oxide Integrity
• Enhanced fluorescence by controlled surface roughness of plastic biochip (Special issue: Microprocesses and nanotechnology)
• Damage Free Particle Removal from Extreme Ultraviolet Lithography Mask Layers by High Energy Laser Shock Wave Cleaning
• Effect of Alkaline pH on Polishing and Etching of Single and Polycrystalline Silicon
• Reaction of Ozone and H2O2 in NH4OH Solutions and Their Reaction with Silicon Wafers
• The Effect of Hydrogen Peroxide on Frictional and Thermal Behaviors in a Citric Acid-Based Copper Chemical Mechanical Planarization Slurry
• Effective Carbon Contaminant Cleaning Condition Using Ozone Dissolved Water and Megasonic for Ru-Capped Extreme Ultraviolet Lithography Mask
• Fabrication of Large-Area CoNi Mold for Nanoimprint Lithography
• Fabrication of Stainless Steel Mold Using Electrochemical Fabrication Method for Microfluidic Biochip
• Physical and Chemical Characterization of Reused Oxide Chemical Mechanical Planarization Slurry
• Hybrid Cleaning Technology for Enhanced Post-Cu/Low-Dielectric Constant Chemical Mechanical Planarization Cleaning Performance
• Effect of Corrosion Inhibitor, Benzotriazole, in Cu Slurry on Cu Polishing
• The Hydrophilization of Process Wafers in Dilute Hydrogen Peroxide Solutions and Ozonated Deionized Water and Its Effects on Defects and Gate Oxide Integrity
• Hybrid Cleaning Technology for Enhanced Post-Cu/Low-Dielectric Constant Chemical Mechanical Planarization Cleaning Performance (Special Issue : Advanced Metallization for ULSI Applications)

もっと見る 閉じる

スポンサーリンク