Comparison of Nicotinamide, Ethylurea and Polyethylene Glycol as Carriers for Nifedipine Solid Dispersion Systems
スポンサーリンク
概要
- 論文の詳細を見る
The most prevalent means for producing solid dispersions of nifedipine, a poorly water-soluble drug, are the solvent based processes that bring problems of environmental and health. We have investigated the preparation of solid dispersions of nifedipine (mp 173℃) by the fusion method, using nicotinamide, ethylurea, polyethylene glycol (PEG) 6000 and hydroxypropylmethylcellulose (HPMC) as carriers. All these solid dispersions were obtained by cooling at room temperature after heating at 140℃ for 15 min. As a single carrier, nicotinamide, ethylurea and PEG were used because nifedipine dissolved in their fused liquids. Compared with the physical mixtures, the solid dispersions with ethylurea or PEG led to a higher dissolution rate of the drug, whereas the difference in drug release between the physical mixtures and the solid dispersions with nicotinamide was not clear. This peculiarity might be due to the high solubilizing effect of nicotinamide for the drug. The fused mixtures of nicotinamide-, ethylurea- or PEG-HPMC were utilized as combined carriers. HPMC dissolved in the fused liquids of nicotinamide or ethylurea, which was effective in forming the amorphous nifedipine in solid dispersions. This resulted in not only the enhanced dissolution rate but also the supersaturation behavior of nifedipine. Further, for the nicotinamide-HPMC system, the supersaturation level of nifedipine increased with an increase in the HPMC content of solid dispersions. Nicotinamide was more applicable than ethylurea and PEG for preparation of the fused dispersions of nifedipine.
- 公益社団法人日本薬学会の論文
- 1997-10-15
著者
-
Suzuki Hideshi
Fuji Laboratory Janssen Pharmaceutical K. K.
-
Sunada Hisakazu
Faculty Of Pharmacy Meijo University
関連論文
- Studies of Rapidly Disintegrating Tablets in the Oral Cavity Using Co-ground Mixtures of Mannitol with Crospovidone
- Preparation of Rapidly Disintegrating Tablets Containing Itraconazole Solid Dispersions
- Rapidly Disintegrating Tablets Prepared by a Surface-Modifying Method : Comparison of Disintegrants
- Preparation and Evaluation of Solid Dispersions of Nitrendipine Prepared with Fine Silica Particles Using the Melt-Mixing Method
- Preparation and Evaluation of Solid Dispersion for Nitrendipine-Carbopol and Nitrendipine-HPMCP Systems Using a Twin Screw Extruder
- Evaluation of Bitterness Suppression of Macrolide Dry Syrups by Jellies
- Preparation and Evaluation of a Compressed Tablet Rapidly Disintegrating in the Oral Cavity
- Analysis of the Release Process of Phenylpropanolamine Hydrochloride from Ethylcellulose Matrix Granules V. : Release Properties of Ethylcellulose Layered Matrix Granules
- Analysis of the Release Process of Phenylpropanolamine Hydrochloride from Ethylcellulose Matrix Granules IV. Evaluation of the Controlled Release Properties for in Vivo and in Vitro Release Systems
- Analysis of the Release Process of Phenylpropanolamine Hydrochloride from Ethylcellulose Matrix Granules III. Effects of the Dissolution Condition on the Release Process
- Analysis of the Release Process of Phenylropanolamine Hydrochloride from Ethylcellulose Matrix Granules II. Effects of the Binder Solution on the Release Process
- Analysis of the Release Process of Phenylpropanolamine Hydrochloride from Ethylcellulose Matrix Granules
- Preparation of Solid Dispersion for Ethenzamide-Carbopol and Theophylline-Carbopol Systems Using a Twin Screw Extruder
- Improvement of the Dissolution Rate of Nitrendipine Using a New Pulse Combustion Drying Method
- Effect of Several Cellulosic Binders and Method of Their Addition on the Properties and Binder Distribution of Granules Prepared in an Agitating Fluidized Bed
- Effect of Process Variables on the Properties and Binder Distribution of Granules Prepared by a High-Speed Mixer
- Preparation and Evaluation of Combination Tablet Containing Incompatible Active Ingredients
- Release from or through a Wax Matrix System. IV. Generalized Expression of the Release Process for a Reservoir Device Tablet
- Release from or through a Wax Matrix System. III. Basic Properties of Release through the Wax Matrix Layer
- Release from or through a Wax Matrix System. II.^ Basic Properties of Release from or through the Wax Matrix Layer
- Dissolution of Solid Dosage Form. VII. Effect of Shape on the Dissolution of Nondisintegrating Single Component Tablet under Non-sink Condition
- Sustained-Release Progesterone Vaginal Suppositories 1 : Development of Sustained-Release Granule(Biopharmacy)
- Influence of Physicochemical Properties on Drug Release Rate from Hydroxypropylmethylcellulose Matrix Tablets
- Influence of Water-Soluble Polymers on the Dissolution of Nifedipine Solid Dispersions with Combined Carriers
- Preparation and Evaluation of Ibuprofen Solid Dispersion Systems with Kollidon Particles Using a Pulse Combustion Dryer System
- Some Factors Influencing the Dissolution of Solid Dispersions with Nicotinamide and Hydroxypropylmethylcellulose as Combined Carriers
- Effect of Process Variables on the Properties and Binder Distribution of Granules Prepared in a Fluidized Bed
- Release from or through a Wax Matrix System VI. : Analysis and Prediction of the Entire Release Process of the Wax Matrix Tablet
- Release from or through a Wax Matrix System. V. Applicability of the Square-Root Time Law Equation for Release from a Wax Matrix Tablet
- Release from or through a Wax Matrix System.I. Basic Release Properties of the Wax Matrix System
- Mechanistic Studies on Hydrotropic Solubilization of Nifedipine in Nicotinamide Solution
- Indomethacin Controlled Release Matrix Tablet Prepared by Wet Granulation Procedure
- Comparison of Nicotinamide, Ethylurea and Polyethylene Glycol as Carriers for Nifedipine Solid Dispersion Systems