Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines

スポンサーリンク

概要

• 論文の詳細を見る

• Estimation of the errors of a hob and a hobbing machine is necessary in order to improve the hobbing accuracy. This paper focuses on the configurations remaining on the tooth surfaces of hobbed gears, and illustrates analytically the tooth surface configurations caused by the errors of the hob and the hobbing machine. The errors of hobs concerned are the lead variation and the eccentricity, while the errors of the hobbing machine include the variation of the rotational center and the rotational irregularity of the table. The above-mentioned hobbing errors are closely related to the tooth surface configurations, and particularly, the feed marks express the characteristics of the tooth surfaces very well. As a result of the investigation on the tooth surface configurations and the formation mechanism of the feed marks, it is possible to estimate the hobbing errors by the calculated tooth surface configurations of hobbed gears.

• 一般社団法人日本機械学会の論文
• 1989-12-15

著者

• ARIURA Yasutsune

  Faculty of Engineering, Kyushu University

• Umezaki Y

  Kyushu Univ. Fukuoka Jpn

• Umezaki Yoji

  Faculty Of Engineering Kyushu University

• UENO Taku

  Faculty of Engineering, Kyushu Industrial University

• Ueno Taku

  Faculty Of Engineering Kyushu Sangyo University

• Ariura Y

  Kyushu Univ. Fukuoka Jpn

• NAGAO Kazuhide

  Faculty of Engineering, Kyushu University

• Nagao Kazuhide

  Faculty Of Engineering Kyushu University

• Ariura Yasutsune

  Faculty Of Engineering Kyushu University

• Taku Ueno

  Fac. Of Engng. Kyushu Indust. Univ.

• Arlura Yasutsune

  Fac. Of Engng. Kyushu Univ.

関連論文

• GSD-8 LOAD-CARRYING CAPACITY OF AUSTEMPERED DUCTILE IRON (ADI) GEARS : SURFACE DURABILITY OF FINE PARTICLE SHOT-PEENED ADI GEAR(GEAR STRENGTH AND DURABILITY)
• Manufacture and Performance of Cylindrical Gears : An Application of New Finish-Hobs for Increasing Surface Durability
• Load-Carrying Capacity of HB≃340 (Hardened and Tempered) Gears : Influence of Gear Ratio and Surface Roughness on Surface Durability
• Load-Carrying Capacity of Surface-Hardened Gears : Influence of Surface Roughness on Surface Durability : Vibration, Control Engineering, Engineering for Industry
• Manufacture and Performance of Spheroidal Graphite Cast lron Gears : 2nd Report, Load-carrying Capacities of As-cast FCD 70〜80 Gears
• On Tooth Contact Marking and Gear Performance : 2nd Report, Gears with Harmful Tooth Form
• On Tooth Contact Marking and Gear Performance : 1st Report, Fundamental Characteristics of Tooth Contact Marking
• Manufacturing and Performance of Spheroidal Graphite Cast lron Gear : 1st Report, An Application to Medium-hardness Gears
• Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
• Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 4th Report, Effect of Surface-finishing on Surface Durability
• Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 3rd Report, Influences of Difference in Hardness and Roughness on Surface Drability
• Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 2nd Report, Surface Durabilities of the Leaded Free-cutting Steel Hobbed Gears and Honed Gears
• Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 1st Report, Effect of Surface Roughness on the Rolling Contact Fatigue of the Rollers and Surface Durability of the Habbed Gears
• Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines
• Finish Hobbing of Gears with Accurate Tooth Profiles
• An Improvement of the Tooth Profile Accuracy of a Hobbed Gear by Adjusting the Hob Eccentricity
• Improvement of Gear Accuracy in Gear Hobbing : 2nd Report, Investigation of the Causes of Tooth Profile Errors by Comparing Computed Tooth Profile Errors with Measured Ones : Vibration, Control Engineering, Engineering for Industry
• Improvement of Gear Accuracy in Gear Hobbing : 1st Report, A Numerical Analysis of Tooth Profile Errors : Vibration, Control Engineering, Engineering for Industry
• On the Lubrication of Worm Gears
• An Analysis Using Offset Curves for Profiles, Manufacturing and Errors of Plane Cams
• Fundamental Research on Hobbed Gear-tooth Surface Roughness : Influence of the Built-up Edge
• Research on Soluble Cutting Fluids for Gear Cutting : 2nd Report, The Influence of Dilution Ratio and the Effect of Synthetic Fluids
• Research on Soluble Cutting Fluids for Gear Cutting : 1st Report, The Effect of Components of Soluble Fluids and the Range of Application of the Fluids
• Experiments on the Cooling Ability of Cutting Fluids
• Effects of Inclination of Contact Line on Friction and Wear of Worm Gears
• The Lubricant Churning Loss in Spur Gear Systems
• Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : On the Most Suitable Clearance Angle of the Hob
• Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : Cutting Tests Using High Speed Steel Fly-Tools
• GSD-7 INFLUENCES OF SHOT-PEENING ON SURFACE DURABILITY OF AUSTEMPERED DUCTILE IRON(GEAR STRENGTH AND DURABILITY)
• Wear Mechanism of Coated Cemented Carbide Tool in Cutting of Inconel 718 Super - Heat - Resisting Alloy
• Analysis of Effect of Built-Up Edge on Hobbed Gear Tooth Surface Roughness
• A Study of Gear Hobbing : Chiefly on Cutting Hard Gears
• STUDIES ON THE WEAR OF HOB : Influence of Face Roughness of Tooth upon Tool Wear
• RESEARCH ON THE TAPERED HOBS
• Graphic Analysis of Hobbing in Unfinished Space
• The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
• The Numerical Analysis of Hobbing Torques : 2nd Report, On the Hobbing Torques of Different Heat Treated Materials under Various Hobbing Conditions
• Studies on the Internal Gear Hobs : Hobs working like the broach and their cutting test
• On Ideal Shapes of the Relieved Surface of Hob Tooth
• Basic Study on Cutting Forces in Gear Cutting : Theory of Cutting with Two Continuous Symmetrical Cutting Edges
• A Fundamental Study of the Surface Durability of Medium-Hardness Gears : Effects of Combination of Hardness and Surface Roughness
• The Lubrication of Bevel Gears
• Study on the Cutting Forces for Spiral Bevel Gears
• Analyses of Cutting Conditions of Spiral Bevel Gears
• Load Carrying Capacity of Spur Gears : A New Gear-Load Testing Machine and Running-in and Failure of Gears Having a Lengthwise Tooth Error

もっと見る 閉じる

スポンサーリンク