Improvement of Gear Accuracy in Gear Hobbing : 1st Report, A Numerical Analysis of Tooth Profile Errors : Vibration, Control Engineering, Engineering for Industry
スポンサーリンク
概要
- 論文の詳細を見る
Accurate gears are needed in order to obtain a high load carrying capacity. This study aims at manufacturing highly accurate gears by hobbing. In this report, a method for the calculation of tooth profile errors, caused by geometrical hob errors such as profile errors of the hob tooth and the eccentricity of the hob, is proposed. From a comparison of the calculated tooth profile errors with the measured ones in hobbing tests, it is found that tooth profile errors generated by geometrical errors and the eccentricity of the hob can be distinguished from those by dynamic errors of the hobbing process, i.e. vibrations, built-up edges and so on. It is proved that the accuracy of this calculation method is sufficient to study the accuracy of hobbed gears.
- 一般社団法人日本機械学会の論文
著者
-
ARIURA Yasutsune
Faculty of Engineering, Kyushu University
-
Chiu Hua
Faculty Of Engineering Kyushu University
-
Umezaki Y
Kyushu Univ. Fukuoka Jpn
-
Umezaki Yoji
Faculty Of Engineering Kyushu University
-
Ariura Y
Kyushu Univ. Fukuoka Jpn
-
Ariura Yasutsune
Faculty Of Engineering Kyushu University
-
Arlura Yasutsune
Fac. Of Engng. Kyushu Univ.
-
Chiu Hua
Faculty Of Engineering Kyushu Sangyo University
関連論文
- GSD-8 LOAD-CARRYING CAPACITY OF AUSTEMPERED DUCTILE IRON (ADI) GEARS : SURFACE DURABILITY OF FINE PARTICLE SHOT-PEENED ADI GEAR(GEAR STRENGTH AND DURABILITY)
- Manufacture and Performance of Cylindrical Gears : An Application of New Finish-Hobs for Increasing Surface Durability
- Load-Carrying Capacity of HB≃340 (Hardened and Tempered) Gears : Influence of Gear Ratio and Surface Roughness on Surface Durability
- Load-Carrying Capacity of Surface-Hardened Gears : Influence of Surface Roughness on Surface Durability : Vibration, Control Engineering, Engineering for Industry
- Manufacture and Performance of Spheroidal Graphite Cast lron Gears : 2nd Report, Load-carrying Capacities of As-cast FCD 70〜80 Gears
- On Tooth Contact Marking and Gear Performance : 2nd Report, Gears with Harmful Tooth Form
- On Tooth Contact Marking and Gear Performance : 1st Report, Fundamental Characteristics of Tooth Contact Marking
- Manufacturing and Performance of Spheroidal Graphite Cast lron Gear : 1st Report, An Application to Medium-hardness Gears
- Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 4th Report, Effect of Surface-finishing on Surface Durability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 3rd Report, Influences of Difference in Hardness and Roughness on Surface Drability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 2nd Report, Surface Durabilities of the Leaded Free-cutting Steel Hobbed Gears and Honed Gears
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 1st Report, Effect of Surface Roughness on the Rolling Contact Fatigue of the Rollers and Surface Durability of the Habbed Gears
- Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines
- Finish Hobbing of Gears with Accurate Tooth Profiles
- An Improvement of the Tooth Profile Accuracy of a Hobbed Gear by Adjusting the Hob Eccentricity
- Improvement of Gear Accuracy in Gear Hobbing : 2nd Report, Investigation of the Causes of Tooth Profile Errors by Comparing Computed Tooth Profile Errors with Measured Ones : Vibration, Control Engineering, Engineering for Industry
- Improvement of Gear Accuracy in Gear Hobbing : 1st Report, A Numerical Analysis of Tooth Profile Errors : Vibration, Control Engineering, Engineering for Industry
- An Analysis Using Offset Curves for Profiles, Manufacturing and Errors of Plane Cams
- Fundamental Research on Hobbed Gear-tooth Surface Roughness : Influence of the Built-up Edge
- The Lubricant Churning Loss in Spur Gear Systems
- GSD-7 INFLUENCES OF SHOT-PEENING ON SURFACE DURABILITY OF AUSTEMPERED DUCTILE IRON(GEAR STRENGTH AND DURABILITY)
- Wear Mechanism of Coated Cemented Carbide Tool in Cutting of Inconel 718 Super - Heat - Resisting Alloy
- Analysis of Effect of Built-Up Edge on Hobbed Gear Tooth Surface Roughness
- The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
- The Numerical Analysis of Hobbing Torques : 2nd Report, On the Hobbing Torques of Different Heat Treated Materials under Various Hobbing Conditions
- Basic Study on Cutting Forces in Gear Cutting : Theory of Cutting with Two Continuous Symmetrical Cutting Edges
- A Fundamental Study of the Surface Durability of Medium-Hardness Gears : Effects of Combination of Hardness and Surface Roughness