The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
スポンサーリンク
概要
- 論文の詳細を見る
The previous knowledge of the hobbing torques is useful to the strength-design for the hob teeth, the decision of optimum cutting conditions for the strength of the hob teeth and the analysis of vibrations on the hob machine. The hobbing torque is calculated from the cross sectional area of cut of the hob tooth and the specific cutting force of the gear material. This paper presents the calculating method of the cross sectional area of cut of the hob tooth, and also shows the methods of simple turning tests by which the specific cutting forces applied to hobbings are obtained. From the comparison of the calculated hobbing torque waves with the measured ones in hobbing tests, it is confirmed that the profiles of the hobbing torque waves are very much alike.
- 一般社団法人日本機械学会の論文
著者
-
Umezaki Yoji
Faculty Of Engineering Kyushu University
-
Suzuki Toshio
Faculty Of Education And Human Sciences University Of Yamanashi
-
FURUMIYA Yoshihiro
Faculty of Engineering, Kyushu University
-
Furumiya Yoshihiro
Faculty Of Engineering Kyushu University
関連論文
- P-128 The First Total Synthesis of (-)-Methyl Barbascoate
- Heterogeneous Amine Catalyst Grafted on Amorphous Silica : An Effective Organocatalyst for Microwave-promoted Michael Reaction of 1,3-Dicarbonyl Compounds in Water
- P-4 Total Synthesis of (-)-Valeriananoids A,B and C via Autocatalytic Diastereoselective Domino Michael Reaction
- Manufacturing and Performance of Spheroidal Graphite Cast lron Gear : 1st Report, An Application to Medium-hardness Gears
- Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines
- Finish Hobbing of Gears with Accurate Tooth Profiles
- An Improvement of the Tooth Profile Accuracy of a Hobbed Gear by Adjusting the Hob Eccentricity
- Improvement of Gear Accuracy in Gear Hobbing : 2nd Report, Investigation of the Causes of Tooth Profile Errors by Comparing Computed Tooth Profile Errors with Measured Ones : Vibration, Control Engineering, Engineering for Industry
- Improvement of Gear Accuracy in Gear Hobbing : 1st Report, A Numerical Analysis of Tooth Profile Errors : Vibration, Control Engineering, Engineering for Industry
- Nano-silica PAMAM Dendrimer as a Novel Catalyst for Knoevenagel Reactions
- Henry Reaction Catalyzed by Aminopropylated Nanosilica
- Total Synthesis of (-)-12,13-epi-Obtusenyne
- P-139 Synthetic Transformation of Ptychantin into Forskolin and 1,9-Dideoxyforskolin
- (R)-2,2'-Bis(stannyl)-1,1'-binaphthyls as a New Chiral Bis-Metallic Binaphthyl Catalyst
- An Analysis Using Offset Curves for Profiles, Manufacturing and Errors of Plane Cams
- Fundamental Research on Hobbed Gear-tooth Surface Roughness : Influence of the Built-up Edge
- Analysis of Effect of Built-Up Edge on Hobbed Gear Tooth Surface Roughness
- The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
- The Numerical Analysis of Hobbing Torques : 2nd Report, On the Hobbing Torques of Different Heat Treated Materials under Various Hobbing Conditions
- Basic Study on Cutting Forces in Gear Cutting : Theory of Cutting with Two Continuous Symmetrical Cutting Edges
- A Modification of the Numerical Integration Error Method for the Zero-Finding Problem of an Analytic Function
- Study on the Cutting Forces for Spiral Bevel Gears
- Analyses of Cutting Conditions of Spiral Bevel Gears