Study on the Cutting Forces for Spiral Bevel Gears
スポンサーリンク
概要
- 論文の詳細を見る
It is very useful to know the cutting forces of spiral bevel gears for the decision of the stable cutting conditions and design of the spiral bevel gear generators. Therefore, the cutting forces during generation of a spiral bevel gear are measured by a special attachment. Then, the theoretical area of cross section of undeformed chips is calculated and the specific cutting forces are investigated. The result shows that the specific cutting forces vary with the position o gear generation.
- 一般社団法人日本機械学会の論文
著者
-
Kondo Seizo
College Of General Education Kyushu University
-
Ueno Taku
Faculty Of Engineering Kyushu Sangyo University
-
Suzuki Toshio
Faculty Of Engineering Fukuoka University
-
Suzuki Toshio
Faculty Of Education And Human Sciences University Of Yamanashi
関連論文
- P-128 The First Total Synthesis of (-)-Methyl Barbascoate
- Heterogeneous Amine Catalyst Grafted on Amorphous Silica : An Effective Organocatalyst for Microwave-promoted Michael Reaction of 1,3-Dicarbonyl Compounds in Water
- P-4 Total Synthesis of (-)-Valeriananoids A,B and C via Autocatalytic Diastereoselective Domino Michael Reaction
- Manufacture and Performance of Cylindrical Gears : An Application of New Finish-Hobs for Increasing Surface Durability
- Load-Carrying Capacity of HB≃340 (Hardened and Tempered) Gears : Influence of Gear Ratio and Surface Roughness on Surface Durability
- Load-Carrying Capacity of Surface-Hardened Gears : Influence of Surface Roughness on Surface Durability : Vibration, Control Engineering, Engineering for Industry
- Manufacture and Performance of Spheroidal Graphite Cast lron Gears : 2nd Report, Load-carrying Capacities of As-cast FCD 70〜80 Gears
- On Tooth Contact Marking and Gear Performance : 2nd Report, Gears with Harmful Tooth Form
- On Tooth Contact Marking and Gear Performance : 1st Report, Fundamental Characteristics of Tooth Contact Marking
- Manufacturing and Performance of Spheroidal Graphite Cast lron Gear : 1st Report, An Application to Medium-hardness Gears
- Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 4th Report, Effect of Surface-finishing on Surface Durability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 3rd Report, Influences of Difference in Hardness and Roughness on Surface Drability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 2nd Report, Surface Durabilities of the Leaded Free-cutting Steel Hobbed Gears and Honed Gears
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 1st Report, Effect of Surface Roughness on the Rolling Contact Fatigue of the Rollers and Surface Durability of the Habbed Gears
- Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines
- Nano-silica PAMAM Dendrimer as a Novel Catalyst for Knoevenagel Reactions
- Henry Reaction Catalyzed by Aminopropylated Nanosilica
- Total Synthesis of (-)-12,13-epi-Obtusenyne
- P-139 Synthetic Transformation of Ptychantin into Forskolin and 1,9-Dideoxyforskolin
- (R)-2,2'-Bis(stannyl)-1,1'-binaphthyls as a New Chiral Bis-Metallic Binaphthyl Catalyst
- On the Lubrication of Worm Gears
- An Analysis Using Offset Curves for Profiles, Manufacturing and Errors of Plane Cams
- Fundamental Research on Hobbed Gear-tooth Surface Roughness : Influence of the Built-up Edge
- Research on Soluble Cutting Fluids for Gear Cutting : 2nd Report, The Influence of Dilution Ratio and the Effect of Synthetic Fluids
- Research on Soluble Cutting Fluids for Gear Cutting : 1st Report, The Effect of Components of Soluble Fluids and the Range of Application of the Fluids
- Experiments on the Cooling Ability of Cutting Fluids
- Effects of Inclination of Contact Line on Friction and Wear of Worm Gears
- The Lubricant Churning Loss in Spur Gear Systems
- Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : On the Most Suitable Clearance Angle of the Hob
- Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : Cutting Tests Using High Speed Steel Fly-Tools
- Analysis of Effect of Built-Up Edge on Hobbed Gear Tooth Surface Roughness
- A Study of Gear Hobbing : Chiefly on Cutting Hard Gears
- STUDIES ON THE WEAR OF HOB : Influence of Face Roughness of Tooth upon Tool Wear
- RESEARCH ON THE TAPERED HOBS
- Graphic Analysis of Hobbing in Unfinished Space
- The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
- The Numerical Analysis of Hobbing Torques : 2nd Report, On the Hobbing Torques of Different Heat Treated Materials under Various Hobbing Conditions
- Studies on the Internal Gear Hobs : Hobs working like the broach and their cutting test
- On Ideal Shapes of the Relieved Surface of Hob Tooth
- Basic Study on Cutting Forces in Gear Cutting : Theory of Cutting with Two Continuous Symmetrical Cutting Edges
- A Modification of the Numerical Integration Error Method for the Zero-Finding Problem of an Analytic Function
- The Lubrication of Bevel Gears
- Study on the Cutting Forces for Spiral Bevel Gears
- Analyses of Cutting Conditions of Spiral Bevel Gears
- Study on Formate Grinding Method of Constant Depth Tooth Spiral Bevel Gears : (By No. 0 Cutter and Non-Tilting Cutter Shaft)
- Load Carrying Capacity of Spur Gears : A New Gear-Load Testing Machine and Running-in and Failure of Gears Having a Lengthwise Tooth Error