Analyses of Cutting Conditions of Spiral Bevel Gears
スポンサーリンク
概要
- 論文の詳細を見る
This paper is intended to find out the best cutting condition for the purpose of improving the cutting efficiency of a spiral bevel gear and the roughness of its finished surface. But the cutting experiment by the gear generator requires too much trouble. Therefore the authors analysed conditions in which a single blade of the cutter cuts the spiral bevel gear, and clarified the cutting conditions of the single blade, with a view to simplifying the experiment by using a single blade instead of the cutter.
- 一般社団法人日本機械学会の論文
著者
-
Kondo Seizo
College Of General Education Kyushu University
-
Ueno Taku
Faculty Of Engineering Kyushu Sangyo University
-
Suzuki Toshio
Faculty Of Engineering Fukuoka University
-
Suzuki Toshio
Faculty Of Education And Human Sciences University Of Yamanashi
関連論文
- P-128 The First Total Synthesis of (-)-Methyl Barbascoate
- Heterogeneous Amine Catalyst Grafted on Amorphous Silica : An Effective Organocatalyst for Microwave-promoted Michael Reaction of 1,3-Dicarbonyl Compounds in Water
- P-4 Total Synthesis of (-)-Valeriananoids A,B and C via Autocatalytic Diastereoselective Domino Michael Reaction
- Manufacture and Performance of Cylindrical Gears : An Application of New Finish-Hobs for Increasing Surface Durability
- Load-Carrying Capacity of HB≃340 (Hardened and Tempered) Gears : Influence of Gear Ratio and Surface Roughness on Surface Durability
- Load-Carrying Capacity of Surface-Hardened Gears : Influence of Surface Roughness on Surface Durability : Vibration, Control Engineering, Engineering for Industry
- Manufacture and Performance of Spheroidal Graphite Cast lron Gears : 2nd Report, Load-carrying Capacities of As-cast FCD 70〜80 Gears
- On Tooth Contact Marking and Gear Performance : 2nd Report, Gears with Harmful Tooth Form
- On Tooth Contact Marking and Gear Performance : 1st Report, Fundamental Characteristics of Tooth Contact Marking
- Manufacturing and Performance of Spheroidal Graphite Cast lron Gear : 1st Report, An Application to Medium-hardness Gears
- Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 4th Report, Effect of Surface-finishing on Surface Durability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 3rd Report, Influences of Difference in Hardness and Roughness on Surface Drability
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 2nd Report, Surface Durabilities of the Leaded Free-cutting Steel Hobbed Gears and Honed Gears
- Load-carrying Capacity of the HB〓340 (Hardened and Tempered) Gears : 1st Report, Effect of Surface Roughness on the Rolling Contact Fatigue of the Rollers and Surface Durability of the Habbed Gears
- Tooth Surface Configurations Caused by the Errors in Hobs and Hobbing Machines
- Nano-silica PAMAM Dendrimer as a Novel Catalyst for Knoevenagel Reactions
- Henry Reaction Catalyzed by Aminopropylated Nanosilica
- Total Synthesis of (-)-12,13-epi-Obtusenyne
- P-139 Synthetic Transformation of Ptychantin into Forskolin and 1,9-Dideoxyforskolin
- (R)-2,2'-Bis(stannyl)-1,1'-binaphthyls as a New Chiral Bis-Metallic Binaphthyl Catalyst
- On the Lubrication of Worm Gears
- An Analysis Using Offset Curves for Profiles, Manufacturing and Errors of Plane Cams
- Fundamental Research on Hobbed Gear-tooth Surface Roughness : Influence of the Built-up Edge
- Research on Soluble Cutting Fluids for Gear Cutting : 2nd Report, The Influence of Dilution Ratio and the Effect of Synthetic Fluids
- Research on Soluble Cutting Fluids for Gear Cutting : 1st Report, The Effect of Components of Soluble Fluids and the Range of Application of the Fluids
- Experiments on the Cooling Ability of Cutting Fluids
- Effects of Inclination of Contact Line on Friction and Wear of Worm Gears
- The Lubricant Churning Loss in Spur Gear Systems
- Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : On the Most Suitable Clearance Angle of the Hob
- Fundamental Research on the Hobbing of Austempered Spheroidal Graphite Cast Iron : Cutting Tests Using High Speed Steel Fly-Tools
- Analysis of Effect of Built-Up Edge on Hobbed Gear Tooth Surface Roughness
- A Study of Gear Hobbing : Chiefly on Cutting Hard Gears
- STUDIES ON THE WEAR OF HOB : Influence of Face Roughness of Tooth upon Tool Wear
- RESEARCH ON THE TAPERED HOBS
- Graphic Analysis of Hobbing in Unfinished Space
- The Numerical Analysis of Hobbing Torques : 1st Report, On the hobbing torques in various hobbing methods
- The Numerical Analysis of Hobbing Torques : 2nd Report, On the Hobbing Torques of Different Heat Treated Materials under Various Hobbing Conditions
- Studies on the Internal Gear Hobs : Hobs working like the broach and their cutting test
- On Ideal Shapes of the Relieved Surface of Hob Tooth
- Basic Study on Cutting Forces in Gear Cutting : Theory of Cutting with Two Continuous Symmetrical Cutting Edges
- A Modification of the Numerical Integration Error Method for the Zero-Finding Problem of an Analytic Function
- The Lubrication of Bevel Gears
- Study on the Cutting Forces for Spiral Bevel Gears
- Analyses of Cutting Conditions of Spiral Bevel Gears
- Study on Formate Grinding Method of Constant Depth Tooth Spiral Bevel Gears : (By No. 0 Cutter and Non-Tilting Cutter Shaft)
- Load Carrying Capacity of Spur Gears : A New Gear-Load Testing Machine and Running-in and Failure of Gears Having a Lengthwise Tooth Error