Analysis of Electric Resistance of Diffusion-Welded Joint Based on Constriction Resistance(Materials, Metallurgy & Weldability)
スポンサーリンク
概要
- 論文の詳細を見る
New equations giving constriction resistance R_C as a function of area S_M and number density n of true contact spots have been obtained from a model experiment, and applied to the analysis of the electric resistance of the bond interface ΔR for the diffusion-welded joint of titanium. The new equations obtained are described as [numerical formula]…(1) for (S_M/S)<1/4, and [numerical formula]…(2) for (S_M/S) >1/4, where ρ is the resistivity of base metal and S the apparent contact area. It can be seen from these equations that parameter A =(ΔR・S/p) depends only on (S_M/S) and n, if ΔR=R_C Parameter A measured at temperatures from 77K to room temperature for joints of titanium, however, decreased with a rise in the temperature of measurement, and its temperature dependence became less pronounced with the increase in welding temperature and time. On the other hand, area S_M and density n were estimated from fractured surfaces of joints on the assumption that spots where grooves caused by grinding of the faying surface were annihilated corresponded to true contact spots. Parameter A calculated from S_M and n thus obtained was significantly smaller than that measured at 77K and rather in good agreement with that measured at room temperature. This result indicates that not all the true contact spots observed on fractured surfaces corresponded to completely bonded spots having electrical properties identical with those of the base metal. The dependence of A on the temperature of measurement can be accounted for by a model that the bond interface consists of three characteristic spots: unbonded spot, completely bonded spot and incompletely bonded spot containing inclusions such as oxide films.
- 大阪大学の論文
著者
-
Akikawa N
Osaka University:(present Office)kawasaki Heavy Industries Ltd.
-
IKEUCHI Kenji
Osaka University
-
ENJO Toshio
Osaka University
-
AKIKAWA Naofumi
Osaka University
-
OKAZAKI Tsukasa
Osaka University
-
Okazaki Tsukasa
Osaka University:(present Office)nippon Oil & Fats Co. Ltd.
関連論文
- Spark-Sintered W Alloys Doped with LaB_6(Materials, Metallurgy & Weldability)
- Plasma Sintering of New Carbide Electrodes(Physics, Processes, Instruments & Measurements)
- Effects of Shielding Gas Composition on Metal Transfer Phenomena in High Current GMA Welding(Physics, Process, Instruments & Measurements)
- New Aspects of Sensitization Behavior in Recent 316 Type Austenitic Stainless SteelsAustenitic Stainless Steels(Materials, Metallurgy & Weldability)
- Disjunction of Metal/Glass Anodically-bonded Interface by Application of Reverse Voltage(Materials, Metallurgy & Weldability)
- Analysis of Electric Resistance of Diffusion-Welded Joint Based on Constriction Resistance(Materials, Metallurgy & Weldability)
- Degradation in Diffusion-welded Joint of Dissimilar-metal Combination at Elevated Temperatures(Materials, Metallurgy & Weldability)
- Effect of the Roughness of Faying Surface on the Early Process of Diffusion Welding : Fundamental Study of the Early Bonding Process of Diffusion Welding by Means of Electric Resistance Measurement (Report II)
- Effect of Oxide Film on the Early Process of Diffusion Welding : Fundamental Study of the Early Process of Diffusion Welding by Means of Electric Resistance Measurement (Report 1)
- Effect of the Roughness of Faying Surface on the Early Process of Diffusion Welding : Study of the Early Process of Diffusion Welding by Means of the Electric Resistance Measurement (Report II)(Materials, Metallurgy & Weldability)
- Decrease in the Efficiency of Diffusion-Welded Joint between Titanium and Aluminum in a Process of Use at High Temperatures
- Effect of Oxide Film on the Early Process of Diffusion Welding : Study of the Early Process of Diffusion Welding by Means of Electric Resistance Measurement (Report I)
- Diffusion Welding of Copper to Aluminum
- Effect of α⇆β Transformation on the Diffusion Welding of Titanium(Materials, Metallurgy, Weldability)
- Diffusion Welding of Copper to Aluminum(Materials, Metallurgy, Weldability)
- Investigation of Metallography and Behavior of M-A Constituent in Weld HAZ of HSLA Steels(Materials, Metallurgy & Weldability)
- Behavior of Oxide Film in Diffusion Bonding of Aluminum(Materials, Metallurgy & Weldability)
- Effects of Insert-metals on Diffusion Welding of Aluminum to Titanium
- Diffusion Welding of Aluminum to Titanium
- Friction Bonding of Ceramics to Metal with Intermediate Layer(Materials, Metallurgy & Weldability)
- Diffusion Welding of Ti-15%Mo-5%Zr Alloy to Mild Steel (0.06%C)
- Study of Microscopic Process of Diffusion Welding by Electric-Resistance Measurement and Transmission Electron Microscope
- Diffusion Welding of Molybdenum to Hastelloy Alloy X
- Effect of Oxide Morphology on Bond Strength of Diffusion-Bonded Interfaces of Al-Alloys(Materials, Metallurgy & Weldability)
- Interfacial Oxide in Diffusion-Bonded Joints of Al-Binary Alloys by Transmission Electron Microscopy(Materials, Metallurgy & Weldability)
- Behavior of Interfacial Oxide during Diffusion Bonding of Aluminum Alloys and Its Influence on Joint Strength(Materials, Metallurgy & Weldability)
- Review of Mechanical and Metallurgical Investigations of M-A Constituent in Welded Joint in Japan
- Effect of M-A Constituent on Fracture Behavior of 780 and 980MPa Class HSLA Steels Subjected to Weld HAZ Thermal Cycles(Materials, Metallurgy & Weldability)
- Weld HAZ Toughness and Its Improvement in Low Alloy Steel SQV-2A for Pressure Vessels (Report 3) : Toughness Improvement by PWHT(Materials, Metallurgy & Weldability)
- Weld HAZ Toughness and Its Improvement of Low Alloy Steel SQV-2A for Pressure Vessels (Report 2) : Microstructure and Charpy Impact Behavior of Intercritically Reheated Coarse Grained Heat Affected Zone (ICCGHAZ)(Materials, Metallurgy & Weldability)
- Weld HAZ Toughness and Its Improvement of Low Alloy Steel SQV-2A for Pressure Vessels (Report 1) : Effect of cooling time on microstructure and Charpy impact value in single thermal cycle(Materials, Metallurgy & Weldability)
- Influence of Sigma Phase on Hydrogen Induced Cracking of Duplex Stainless Steel(Materials, Metallurgy & Weldability)
- Advanced Stereo Matching Algorithm for Three-dimensional Reconstruction of Fracture Surfaces(Physics, Processes, Instruments & Measurements)
- Microstructure and Toughness in Weld Heat-Affected Zone of Duplex Stainless Steel(Materials, Metallurgy & Weldability)
- Thermo-Mechanical-Metallurgical Model of Welded Steel : Part I : Evolution Equations for Internal Material Structures
- Stress Corrosion Cracking of SUS316 Stainless Steel in High Temperature Water(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking of SUS304 Stainless Steel in High Temperature Water : Effects of Solution Treatment Temperature and Sensitization Treatment(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking of SUS304 Stainless Steel in High Temperature Water : Effect of Dissolved Oxygen and Strain Rate(Materials, Metallurgy & Weldability)
- Influence of Surface Treatment on the Strength of Solid-State Diffusion-Bonded Interface of Tin(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Effects of Alloying Elements on the Strength of Friction-bonded Interfaces of Al Alloys to Steel(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Impact Fracture Behavior of Duplex Stainless Steel Weldment(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Microstructure and Mechanical Properties of Weld Metals of 950MPa Class High-strength Steel(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Effect of Simulated Welding Cycles on Carbide Evolution in SQV 2A Low Alloy Steel(Materials, Metallurgy & Weldability)
- Three-Dimensional Reconstruction of Fracture Surface Using Area Matching Algorithm(Physics, Processes, Instruments & Measurements)
- Low Temperature Mechanical Properties of High-Nitrogen Type 316 Austenitic Stainless Steel Weld Metals : Gas Shielded Arc Welding of High-Nitrogen Type 316 Austenitic Stainless Steel (Report 2)
- Gas Shielded Arc Welding of High-Nitrogen Austenitic Stainless Steel (Report 1)(Materials, Metallurgy, Weldability)
- Analysis of Structural Features of Hard-Facing Overlays Performed Using Prototype Selfshielded Flux Cored Wires(Materials, Metallurgy & Weldability)
- Development of Intermediate Layer for Diffusion Bonding of Continuous Alumina Fiber Reinforced Aluminum Matrix Composite(Materials, Metallurgy & Weldability)
- Effects of Ultrasonic Vibration on Diffusion Welding of Aluminum(Materials, Metallurgy & Weldability)
- Diffusion Welding of Al-Cu-Mg Series A2017 Alloy to Titanium(Materials, Metallurgy & Weldability)
- Diffusion Bonding of Al-Mg-Si Series 6063 Alloy Reinforced with Alumina Short Fibers(Materials, Metallurgy & Weldability)
- Investigation of M-A Constituent in High Strength Steel Welds
- Corrosion Characteristics in Weld Heat-affected Zone of Al-Zn-Mg Alloy(Materials, Metallugy & Weldability)
- Microstructure and Toughness in Weld Metal of High Purity Ferritic Stainless Steel(Materials, Metallurgy & Weldability)
- Effect of Minor Alloying Elements on Corrosion Resistance of Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Friction Welding of Silicon Carbide to Nickel with Intermediate Layer(Materials, Metallurgy & Weldability)
- ReibschweiBen von Kupfer-Sinterlegierung auf zahgepoltes Kupfer(Physics, Process, Instrument & Measurement)
- Effect of Microstructure on Hydride Precipitation in Ti-6A1-4V Alloy(Materials, Metallurgy & Weldability)
- Effects of Impurity in Aluminum on Diffusion Welding of Aluminum to Titanium(Materials, Metallurgy & Weldability)
- Lamellar Tearing of 5083 Aluminum Alloy and Its Welds(Materials, Metallurgy, Weldability)
- Effects of Relatively Insoluble Compounds and β Phase on Stress Corrosion Cracking in 5083 Aluminum Alloy(Materials, Metallurgy, Weldability)
- Microstructure and Mechanical Properties in Weld Heat Affected Zone of Titanium Alloy(Materials, Metallurgy & Weldability)
- Effect of Copper Addition on Corrosion Resistance of Commercial Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Analysis of Fracture Morphology in Hydrogen Embrittlement for Cr-Mo Steel(Materials, Metallurgy & Weldability)
- Effect of Hydride Precipitation Behavior on Fracture Morphology for Ti-6Al-4V Alloy(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking in Welds of Al-Zn-Mg System 7NO1-T4 Alloy(Materials, Metallurgy, Weldability)
- Hydride Precipitation Behavior in α+β Ti-6Al-4V Alloy(Materials, Metallurgy & Weldability)
- Microstructure in Weld Heat Affected Zone of Al-Mg-Si Alloy(MATERIALS METALLURGY AND WELDABILITY)
- Effect of Minor Alloy Additions on Aging Characteristics in Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Diffusion Welding of Al-Cu-Mg Series 2017 Alloy(Materials, Metallurgy & Weldability)
- What's Brought by Micro- and Nanoscopic Approaches to Joining & Welding Metallurgy?(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Development of Microstructure of the Anodically-bonded Interface between Aluminum and Borosilicate Glass(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)