Effect of Minor Alloying Elements on Corrosion Resistance of Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
スポンサーリンク
概要
- 論文の詳細を見る
An investigation has been made of the effect of minor alloying elements on the corrosion resistance of Al-Zn-Mg alloy welds using a commercial Al-Zn-Mg alloy (7N01) and four kinds of Al-Zn Mg alloys separately added 0.05% Ti, 0.2% Fe-0.1% Si, 0.5%Mn and 0.2%Cr by means of the pitting potential of anodic polarization curve and electrical resistivity measurement. The pitting potential in anodic polarization curve was related to the resistivity showing the solution of the minor alloy in the matrix rather than the weight percent of minor alloying addition. The addition of 0.05% Ti to the Al-Zn Mg alloy hardly shows the increase of the resistivity, and hardly affects the age hardening characteristics and pitting potential. The addition of 0.2%Fe-0.1%Si to the alloy hardly shows the increase of the resistivity, and hardly affects the pitting potential, but markedly affects the age hardening characteristics at 120℃. The addition of 0.5%Mn to the alloy causes the markedly increase of the resistivity, and markedly causes the increase of the pitting potential for aged specimen but hardly affects the age hardening at 120℃. The addition of 0.2%Cr to the alloy affects both age hardening characteristics and the pitting potential. The age hardening at 120℃ hardly occurs by the addition of Cr, but the pitting potential is improved. The pitting potential depends on not only the amount of minor alloying elements but also the solution treatment temperature. As the relatively insoluble compounds is fairly solutionized in the matrix at 560℃ solution temperature, the solute concentration of Cr increases in the matrix, and then the pitting potential increases and becomes more noble.
- 大阪大学の論文
著者
-
KURODA Toshio
Osaka University
-
ENJO Toshio
Osaka University
-
Enjo T
Osaka University
-
Enjo Toshio
Welding Research Institute Osaka University
-
Kuroda T
Osaka University
-
KANAMITSU Shinya
Osaka University
関連論文
- New Aspects of Sensitization Behavior in Recent 316 Type Austenitic Stainless SteelsAustenitic Stainless Steels(Materials, Metallurgy & Weldability)
- Analysis of Electric Resistance of Diffusion-Welded Joint Based on Constriction Resistance(Materials, Metallurgy & Weldability)
- Degradation in Diffusion-welded Joint of Dissimilar-metal Combination at Elevated Temperatures(Materials, Metallurgy & Weldability)
- Effect of the Roughness of Faying Surface on the Early Process of Diffusion Welding : Study of the Early Process of Diffusion Welding by Means of the Electric Resistance Measurement (Report II)(Materials, Metallurgy & Weldability)
- Effect of Oxide Film on the Early Process of Diffusion Welding : Study of the Early Process of Diffusion Welding by Means of Electric Resistance Measurement (Report I)
- Effect of α⇆β Transformation on the Diffusion Welding of Titanium(Materials, Metallurgy, Weldability)
- Diffusion Welding of Copper to Aluminum(Materials, Metallurgy, Weldability)
- Stress Corrosion Cracking Susceptibilities of Carbon Steels in High Temperature and High Pressure Water(Materials, Metallurgy & Weldability)
- Behavior of Oxide Film in Diffusion Bonding of Aluminum(Materials, Metallurgy & Weldability)
- Effect of Relatively Insoluble Compounds on β Phase Precipitation in 5083 Aluminum Alloy
- New Internal Friction Peak in Hydrogenated Palladium(Materials, Metallurgy & Weldability)
- Special Issue on Joining Technology for New Metallic Glasses and Inorganic Materials - Selected Papers from the IUMRS International Conference in Asia 2008 (IUMRS-ICA2008)
- Influence of Sigma Phase on Hydrogen Induced Cracking of Duplex Stainless Steel(Materials, Metallurgy & Weldability)
- Advanced Stereo Matching Algorithm for Three-dimensional Reconstruction of Fracture Surfaces(Physics, Processes, Instruments & Measurements)
- INTERNAL FRICTION PEAK BY HYDROGEN IN DUPLEX STAINLESS STEEL AND ITS WELD METAL
- Effect of Microstructure on Fracture Toughness of SUS329J1 Duplex Stainless Steel Welds
- Microstructure and Toughness in Weld Heat-Affected Zone of Duplex Stainless Steel(Materials, Metallurgy & Weldability)
- Oxygen Content and Fracture Toughness of MIG Weld Metal of SUS304 Steel
- Stress Corrosion Cracking of SUS316 Stainless Steel in High Temperature Water(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking of SUS304 Stainless Steel in High Temperature Water : Effects of Solution Treatment Temperature and Sensitization Treatment(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking of SUS304 Stainless Steel in High Temperature Water : Effect of Dissolved Oxygen and Strain Rate(Materials, Metallurgy & Weldability)
- Impact Fracture Behavior of Duplex Stainless Steel Weldment(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Microstructure and Mechanical Properties of Weld Metals of 950MPa Class High-strength Steel(Materials, Metallurgy & Weldability, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Effect of Simulated Welding Cycles on Carbide Evolution in SQV 2A Low Alloy Steel(Materials, Metallurgy & Weldability)
- Three-Dimensional Reconstruction of Fracture Surface Using Area Matching Algorithm(Physics, Processes, Instruments & Measurements)
- Low Temperature Mechanical Properties of High-Nitrogen Type 316 Austenitic Stainless Steel Weld Metals : Gas Shielded Arc Welding of High-Nitrogen Type 316 Austenitic Stainless Steel (Report 2)
- Gas Shielded Arc Welding of High-Nitrogen Austenitic Stainless Steel (Report 1)(Materials, Metallurgy, Weldability)
- Analysis of Structural Features of Hard-Facing Overlays Performed Using Prototype Selfshielded Flux Cored Wires(Materials, Metallurgy & Weldability)
- Effects of Ultrasonic Vibration on Diffusion Welding of Aluminum(Materials, Metallurgy & Weldability)
- Diffusion Welding of Al-Cu-Mg Series A2017 Alloy to Titanium(Materials, Metallurgy & Weldability)
- Diffusion Bonding of Al-Mg-Si Series 6063 Alloy Reinforced with Alumina Short Fibers(Materials, Metallurgy & Weldability)
- Microstructure in Weld Heat-affected Zone of Beta Titanium Alloy(Materials, Metallugy & Weldability)
- Corrosion Characteristics in Weld Heat-affected Zone of Al-Zn-Mg Alloy(Materials, Metallugy & Weldability)
- Microstructure and Toughness in Weld Metal of High Purity Ferritic Stainless Steel(Materials, Metallurgy & Weldability)
- Effect of Minor Alloying Elements on Corrosion Resistance of Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Friction Welding of Copper-Tungsten Sintered Alloy to Pure Aluminum : Formation of Intermetallic Compound at Weld (Report 1)
- Friction Welding Of Copper-Tungsten Sintered Alloy to Pure Titanium : Formation of Intermetallic Compound at Weld (Report 2)
- Friction Welding of Copper-Tungsten Sintered Alloy to Pure Aluminum : Formation of Intermetallic Compound at Weld (Report 1)
- Friction Welding of Oxygen Free Copper to Pure Aluminum
- ReibschweiBen von Kupfer-Sinterlegierung auf zahgepoltes Kupfer(Physics, Process, Instrument & Measurement)
- Effect of Copper Oxide on Joint Strength of Friction Welding of Copper-Tungsten Sintered Alloy to Tough Pitch Copper
- Effect of Microstructure on Hydride Precipitation in Ti-6A1-4V Alloy(Materials, Metallurgy & Weldability)
- Effects of Impurity in Aluminum on Diffusion Welding of Aluminum to Titanium(Materials, Metallurgy & Weldability)
- Lamellar Tearing of 5083 Aluminum Alloy and Its Welds(Materials, Metallurgy, Weldability)
- Effects of Relatively Insoluble Compounds and β Phase on Stress Corrosion Cracking in 5083 Aluminum Alloy(Materials, Metallurgy, Weldability)
- Microstructure and Mechanical Properties in Weld Heat Affected Zone of Titanium Alloy(Materials, Metallurgy & Weldability)
- Effect of Copper Addition on Corrosion Resistance of Commercial Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Analysis of Fracture Morphology in Hydrogen Embrittlement for Cr-Mo Steel(Materials, Metallurgy & Weldability)
- Effect of Hydride Precipitation Behavior on Fracture Morphology for Ti-6Al-4V Alloy(Materials, Metallurgy & Weldability)
- Stress Corrosion Cracking in Welds of Al-Zn-Mg System 7NO1-T4 Alloy(Materials, Metallurgy, Weldability)
- Hydride Precipitation Behavior in α+β Ti-6Al-4V Alloy(Materials, Metallurgy & Weldability)
- Microstructure in Weld Heat Affected Zone of Al-Mg-Si Alloy(MATERIALS METALLURGY AND WELDABILITY)
- Effect of Minor Alloy Additions on Aging Characteristics in Al-Zn-Mg Alloy Welds(Materials, Metallurgy & Weldability)
- Role of Secondary Austenite on Corrosion and Stress Corrosion Cracking of Sensitized Duplex Stainless Steel Weldments(Materials, Metallurgy & Weldability)
- Helium Bubble Kinetics during Laser Welding of Helium-Doped Stainless Steel(Materials, Metallurgy & Weldability)
- Diffusion Welding of Al-Cu-Mg Series 2017 Alloy(Materials, Metallurgy & Weldability)