Vacuum Brazing Tests on Powder Aluminum Brazing Filler Metals(Materials, Metallurgy & Weldability)
スポンサーリンク
概要
- 論文の詳細を見る
Vacuum brazing tests on powder aluminum brazing filler metals were conducted using various atomized Al-Si-Mg powders to investigate their applicability for the vacuum process. The effect of atomizing condition, powder size and filler metal composition has been studied to obtain an optimum powder for the vacuum process. After brazing apart of each filler metal used made no contribution to the fillet formation and coalesced on the base metal. This indicated non-wetting tendencies among filler metal powders. Brazability was evaluated by the percentage of the filler metal remaining as fillet by measuring the weight change before and after brazing. After brazing, voids were found in the formed fillet. Although, completely sound fillets were not obtained, fine powders and air atomized powders gave better brazability than coarse powders and those atomized in argon gas atmosphere. The difference in vaporization characteristics of magnesium in the filler metals seemed to be responsible for void formation and poor brazability of the powder filler metals. Mixing of the filler metals with Al-Mg powder was found to be effective for the improvement of the fillet formation, however, completely sound fillets were not obtained. It is believed that both the control of magnesium vaporization rate and improvement in the quality of the vacuum are important to obtain sound fillets.
- 大阪大学の論文
著者
-
MIZUTANI Masami
Osaka University
-
Matsunawa Akira
Joining and Welding Research Institute, Osaka University
-
Mizutani Masami
JWRI, Osaka University
-
TAKEMOTO Tadashi
Osaka University
-
Takemoto Tadashi
Department of Experimental Radiology, Shiga University of Medical Science
-
MATSUNAWA Akira
Osaka University
-
Matsunawa Akira
Joining And Welding Research Institute Osaka University
-
Takemoto Tadashi
Department Of Experimental Radiology Shiga University Of Medical Science
-
Takemoto T
Osaka Univ. Osaka Jpn
-
Matsunawa A
Joining And Welding Research Institute Osaka University
-
UJIE Tatsuyuki
Toyo Aluminum K.K.
-
TANAKA Akiei
Toyo Aluminum K.K.
-
Mizutani M
Osaka Univ. Osaka Jpn
-
Mizutani Masami
Jwri Osaka University
関連論文
- Elucidation of Laser Welding Phenomena and Porosity Formation Mechanism(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Laser Weldability of Aluminum Alloys(Physics, Processes, Instruments & Measurements)
- Observation of Keyhole and Molten Pool Behaviour in High Power Laser Welding : Mechanism of Porosity Formation and Its Suppression Method
- Physical Meaning of Wetting Curve Traced by Meniscograph Wettability Tester (Report II) : Kinetic Consideration of Flux Action in Soldering(Welding Physics, Process & Instrument)
- Physical Meaning of Wetting Curve Traced by Meniscograph Wettability Tester(Welding Physics, Process & Instrument)
- Laser PVD of Al_2O_3(Surface Processing)
- Spreading of BAg-5 on Pre-Flux Coated Stainless Steel Plate : Function of Fluxes Mixed with NiCl_2 or FeCl_3
- THE ORIGIN AND THE EVOLUTION OF THE THIOESTER-CONTAINING PROTEIN(Physiology,Abstracts of papers presented at the 74^ Annual Meeting of the Zoological Society of Japan)
- FUNCTIONAL INVESTIGATION OF THE DRP/DHP/CRAM/UNC-33 FAMILY IN PLANARIANS, DUGESIA JAPONICA(Developmental Biology,Abstracts of papers presented at the 74^ Annual Meeting of the Zoological Society of Japan)
- Laser Physical Vapor Deposition of Si_3N_4 and SiC, and Film Formation Mechanism(Materials, Metallurgy & Weldability)
- Laser Rapid Solidification Microstructure in Single Crystals of Al and Al-2% Cu Alloys(Materials, Metallugy & Weldability)
- Spectroscopic Measurement of Plume in Laser PVD Process
- Mathematical Modeling of Fusion and Solidification in Laser Welding and Evaluation of Hot Cracking Susceptibility
- Ceramic Coating of Titanium by Pulsed YAG Laser(Physics, Process & Instrument)
- Laser Production of Ultrafine Particles of Ceramics and Ceramic-Metal Mixtures(Fine Particles)
- 3'-Blocking Damage of DNA as a Mutagenic Lesion Caused by Hydrogen Peroxide in Escherichia coli
- Laser Production of Metallic Ultra-Fine Particles(Welding Physics, Process & Instrument)
- Laser Production of Ultra-Fine Particles
- Heat and Mass Transfer and Their Effect on Penetration Shape in Stationary TIG Arc Weld Pool
- Effect of Hole in Brazing Sheet on Vacuum Brazability of Aluminum Tubes
- Erosion of Pure Copper by Copper Phosphorus Brazing Filler Metals containing Tin and Silver : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report V)(Physics, Process, Instrument & Measurement)
- Spreading of Copper Phosphorus Brazing Filler Metals with Low Melting Temperature containing silver and/or Tin : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report IV)(Physics, Process, Instrument & Measurement)
- Liquidus Surface of Quaternary Copper Phosphorus Brazing Filler Metals with Silver and Tin : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report III)(Materials, Metallurgy & Weldability)
- Phase Diagrams of Cu-Ag-P and Cu-Sn-P Ternary Brazing Filler Metals : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature-Report II(Materials, Metallurgy & Weldability)
- Dynamic Characteristics of Variable Frequency Pulsed TIG Arc(Welding Physics, Process & Instrument)
- Experimental Study on Dynamic Properties of Power Sources for MIG/MAG Welding(Welding Physics, Process & Instrument)
- Penetration Characteristics and Plume Behavior in Laser-Arc Hybrid Welding(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- High Temperature Corrosion of Nickel Based Heat Resistant Alloys and their Diffusion Brazed Parts(Materials, Metallurgy & Weldability)
- Correlation among Solidification Process, Microstructure, Microsegregation and Solidification Cracking Susceptibility in Stainless Steel Weld Metals(Materials, Metallurgy & Weldability)
- Welding Phenomena and Reflected Beam Monitoring during YAG Laser Lap Welding of Zn-Coated Steels(Physics, Processes, Instruments & Measurements)
- Strategic Vision of Materials Joining in Japan
- Reaction of Iron-based Alloys with Molten Lead-free Solder(Materials, Metallurgy & Weldability)
- Sacrificial Anode Type Al-10Si-1Mg Brazing Filler Metals for Suppression of Corrosion of Brazed 3003 Aluminum Alloy(Materials, Metallurgy & Weldability)
- Conditions for the Measurement of Surface Tension of Solders with a Wetting Balance Tester(Materials, Metallurgy & Weldability)
- Vacuum Brazing Tests on Powder Aluminum Brazing Filler Metals(Materials, Metallurgy & Weldability)
- Effect of Flux Composition on Wettability in Soldering of Aluminum(Materials, Metallurgy & Weldability)
- Effect of Curvature on Fillet Formation during Aluminum Brazing(Materials, Metallurgy & Weldability)
- Strength of Titanium Joints Brazed with Aluminum Filler Metals(Physics, Process, Instrument & Measurement)
- Aluminum Brazing Filler Metals for Making Aluminum to Titanium Joints in a Vacuum(Physics, Process, Instrument & Measurement)
- Analysis of Temperature Field with Equiradial Cooling Boundary around Moving Heat Sources : Heat Conduction Analysis for Estimation of Thermal Hysteresis during Underwater Welding(Welding Physics, Processes & Instruments)
- Spreading of BAg-5 on Pre-Flux Coated Stainless Steel Plate (Report II) : Function of Fluxes Mixed with CuCl or CoCl_2(Welding Physics, Processes & Instruments)
- H_2S Gas Corrosion Resistance of Copper Joints Brazed with Low Melting Temperature Copper Phosphorus Brazing Filler Metals(Mechanics, Strength & Structural Design)
- Copper Phosphorus Brazing Filler Alloys with Low Melting Temperature (Report I) : Effect of Tin Addition
- Interaction between Supersonic Jet and Burning Iron Wall in Oxygen Gas Cutting (Part II) : Combustion Stability and Flame Cutting Mechanism(Welding Physics, Process & Instrument)
- Interaction between Supersonic Jet and Burning Iron Wall in Oxygen Gas Cutting (Part I) : Shock Wave Behaviour and Combustion Phenomena(Welding Physics, Process & Instrument)
- Merkmale Verschiendener Betriebsurwachunegsmethoden und Deren Anwendung im Rahmen Der Laserschweisstechnik : Features of Various In-process Monitoring Methods and Their Applications to Laser Welding(Physics, Processes, Instruments & Measurements)
- Laser Beam Welding of Lap Joints of Dissimilar Materials(Physics, Processes, Instruments & Measurements)
- Stress Corrosion Cracking Mechanism of Cu-4% Ti Alloy(Welding Mechanics, Strength & Design)
- Analysis of Temperature Distribution with Radial Symmetrical Cooling Terminal around Moving Heat Source
- Vacuum Brazing of Aluminum Using Al-12%Si System Filler Alloy
- Vacuum Brazing of Aluminum Using Al-12%Si System Filler Alloy
- Role of Surface Tension in Fusion Welding (Part 3) : Hydrodynamic Effect
- Role of Surface Tension in Fusion Welding (Part 1) : Hydrostatic Effect
- Role of Surface Tension in Fusion Welding (Part 2) : Hydrostatic Effect
- Notch Formation Mechanism in Low Speed Oxygen Gas Cutting
- Temperature Distribution along Thin Rod with Radiation Loss from Side Surface
- Newborn JWRI : The Concept and Purpose of Reorganization
- Stress Corrosion Cracking and Anodic Dissolution Behavior of 5083 Aluminum Alloy(Materials, Metallurgy & Weldability)
- Effect of Iron Content in Brazing Filler Metals on Corrosion of Brazed Aluminum(Materials, Metallurgy & Weldability)
- Corrosion Behaviour of Silver Brazed Stainless Steel in Chloride Solutions(Materials, Metallurgy, Weldability)
- Vacuum Brazing of Aluminum (Report-I) : Effect of Surface Treatment
- Corrosion Mechanism of Silver Brazed Stainless Steel Joint in Chloride Solutions(Materials, Metallurgy, Weldability)
- Vacuum Brazing of Aluminum (Report-II) : Effect of Emery Paper Grinding
- Fundamental Characteristics of the Hollow Cathode Arc as Welding Heat Source(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Brazability of Aluminum using Al-Si Filler Alloys with Different Compositions and Microstructures
- Effect of Bismuth Addition to Brazing Sheet Claddings on Fluxless Brazability of Aluminum(Welding Physics, Process & Instrument)
- Brazability and Erosion by Molten Filler Alloy of Aluminum Base Plates with Intermetallic Compounds(Materials, Metallurgy & Weldability)