Fundamental Characteristics of the Hollow Cathode Arc as Welding Heat Source(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
スポンサーリンク
概要
- 論文の詳細を見る
A feasibility study has been conducted to determine whether the Hollow Cathode Arc (HCA) can be used for a welding heat source in space, that is with high vacuum and microgravity conditions. The HCA is a low pressure arc discharge, which is formed under low pressure conditions by purging a small amount of gas through the center of the hollow cathode. Investigations into the characteristics of HCA have been experimentally performed. In the present paper, fundamental characteristics of the HCA in a vacuum chamber, such as volt-ampere characteristics, melting properties and plasma properties, have been investigated. Results show that, under the condition that the gas flowrate is low, the HCA column is concentrated under the cathode and the HCA is characterized by a high arc voltage and a high electron temperature. Regarding melting properties, penetration profiles for the HCA melting are sensitive to gas flowrate, and deep penetration can be formed if the gas flowrate is low.
- 大阪大学の論文
著者
-
TAKEMOTO Tadashi
Osaka University
-
Ohji T
Osaka University
-
Ohji Takayoshi
Osaka University
-
Nishikawa Hiroshi
Osaka University
関連論文
- Physical Meaning of Wetting Curve Traced by Meniscograph Wettability Tester (Report II) : Kinetic Consideration of Flux Action in Soldering(Welding Physics, Process & Instrument)
- Physical Meaning of Wetting Curve Traced by Meniscograph Wettability Tester(Welding Physics, Process & Instrument)
- Spreading of BAg-5 on Pre-Flux Coated Stainless Steel Plate : Function of Fluxes Mixed with NiCl_2 or FeCl_3
- Effect of Hole in Brazing Sheet on Vacuum Brazability of Aluminum Tubes
- Erosion of Pure Copper by Copper Phosphorus Brazing Filler Metals containing Tin and Silver : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report V)(Physics, Process, Instrument & Measurement)
- Spreading of Copper Phosphorus Brazing Filler Metals with Low Melting Temperature containing silver and/or Tin : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report IV)(Physics, Process, Instrument & Measurement)
- Liquidus Surface of Quaternary Copper Phosphorus Brazing Filler Metals with Silver and Tin : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature (Report III)(Materials, Metallurgy & Weldability)
- Phase Diagrams of Cu-Ag-P and Cu-Sn-P Ternary Brazing Filler Metals : Copper Phosphorus Brazing Filler Metals with Low Melting Temperature-Report II(Materials, Metallurgy & Weldability)
- High Temperature Corrosion of Nickel Based Heat Resistant Alloys and their Diffusion Brazed Parts(Materials, Metallurgy & Weldability)
- Reaction of Iron-based Alloys with Molten Lead-free Solder(Materials, Metallurgy & Weldability)
- Sacrificial Anode Type Al-10Si-1Mg Brazing Filler Metals for Suppression of Corrosion of Brazed 3003 Aluminum Alloy(Materials, Metallurgy & Weldability)
- Conditions for the Measurement of Surface Tension of Solders with a Wetting Balance Tester(Materials, Metallurgy & Weldability)
- Vacuum Brazing Tests on Powder Aluminum Brazing Filler Metals(Materials, Metallurgy & Weldability)
- Effect of Flux Composition on Wettability in Soldering of Aluminum(Materials, Metallurgy & Weldability)
- Effect of Curvature on Fillet Formation during Aluminum Brazing(Materials, Metallurgy & Weldability)
- Strength of Titanium Joints Brazed with Aluminum Filler Metals(Physics, Process, Instrument & Measurement)
- Aluminum Brazing Filler Metals for Making Aluminum to Titanium Joints in a Vacuum(Physics, Process, Instrument & Measurement)
- Spreading of BAg-5 on Pre-Flux Coated Stainless Steel Plate (Report II) : Function of Fluxes Mixed with CuCl or CoCl_2(Welding Physics, Processes & Instruments)
- Deposition of Hydroxyapatite Film on Titanium by Ultra-fine Particle Beam(Physics, Processes, Instruments & Measurements)
- H_2S Gas Corrosion Resistance of Copper Joints Brazed with Low Melting Temperature Copper Phosphorus Brazing Filler Metals(Mechanics, Strength & Structural Design)
- Copper Phosphorus Brazing Filler Alloys with Low Melting Temperature (Report I) : Effect of Tin Addition
- Stress Corrosion Cracking Mechanism of Cu-4% Ti Alloy(Welding Mechanics, Strength & Design)
- Vacuum Brazing of Aluminum Using Al-12%Si System Filler Alloy
- Vacuum Brazing of Aluminum Using Al-12%Si System Filler Alloy
- Stress Corrosion Cracking and Anodic Dissolution Behavior of 5083 Aluminum Alloy(Materials, Metallurgy & Weldability)
- Effect of Iron Content in Brazing Filler Metals on Corrosion of Brazed Aluminum(Materials, Metallurgy & Weldability)
- Corrosion Behaviour of Silver Brazed Stainless Steel in Chloride Solutions(Materials, Metallurgy, Weldability)
- Vacuum Brazing of Aluminum (Report-I) : Effect of Surface Treatment
- Corrosion Mechanism of Silver Brazed Stainless Steel Joint in Chloride Solutions(Materials, Metallurgy, Weldability)
- Vacuum Brazing of Aluminum (Report-II) : Effect of Emery Paper Grinding
- Fundamental Characteristics of the Hollow Cathode Arc as Welding Heat Source(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Brazability of Aluminum using Al-Si Filler Alloys with Different Compositions and Microstructures
- Effect of Bismuth Addition to Brazing Sheet Claddings on Fluxless Brazability of Aluminum(Welding Physics, Process & Instrument)
- Brazability and Erosion by Molten Filler Alloy of Aluminum Base Plates with Intermetallic Compounds(Materials, Metallurgy & Weldability)