1/3-Harmonic and Parametric Combination Resonance of a Roller Chain : Vibration, Control Engineering, Engineering for Industry
スポンサーリンク
概要
- 論文の詳細を見る
This paper reports on a comparison of the experimental and analytical results of the 1/3-harmonic and parametric combination resonance of a roller chain stretched vertically, which is regarded as a system with many degrees of freedom when the elongation of the chain during vibration is taken into account. A representative frictional coefficient is determined, and the influence of the phase angle between the forced displacement and the prescribed tension fluctuation on the combination resonance are examined using a chain with comparatively large friction. A comparison between characteristics of the combination resonances and the 1/3-harmonic vibration is also made. A good agreement between experimental and analytical results was confirmed.
- 一般社団法人日本機械学会の論文
著者
-
Sueoka Atsuo
Faculty Of Engineering Kyushu University
-
TAMURA Hideyuki
Faculty of Engineering, Kyushu University
-
Kondou Takahiro
Faculty Of Engineering Fukuoka Institute Of Technology
-
Tamura H
Department Of Intelligent Machinery And Systems Faculty Of Engineering Kyushu University
-
FURUKAWA Tomoyoshi
Nippon Kokan Ltd.
-
Tamura Hideyuki
Faculty Of Engineering Kyoto University
関連論文
- 集中系モデルによる非線形圧力波の解析 : 第3報,急拡大・急縮小要素のモデル化(機械力学,計測,自動制御)
- 102 楕円型平均法による2自由度非線形振動系の解析
- フレキシブル継手と剛体円板を用いたポンプ配管系の振動低減対策 : 直線状配管を対象とした検討(機械力学,計測,自動制御)
- 439 レンツの法則に基づいた磁気ダンパ
- 524 部分空間制御法による多重倒立振子の振り上げ制御
- 集中系モデルによる非線形圧力波の解析 : 第2報,分岐要素のモデル化とその妥当性の検証(機械力学,計測,自動制御)
- 部分空間制御法を用いた2リンクフレキシブルマニピュレータのCP制御(D&D 2008)
- 集中系モデルによる非線形圧力波の解析 : 第1報,解析モデルの提案とその妥当性の検証(D&D 2008)
- 大規模非線形系に対する高性能振動解析手法の開発 : 非線形支持された直線状はり構造物の曲げ振動への適用(機械力学,計測,自動制御)
- モード解析に基づく部分空間制御法に関する研究 : 第2報,非線形共振を利用した並列二重倒立振子の振り上げ制御(機械力学,計測,自動制御)
- 523 非線形共振を利用した振り子の振動制御
- 525 部分空間制御法を用いた2リンクフレキシブルマニピュレータのCP制御
- 206 疑似焼き鈍し法を援用した遺伝的アルゴリズムによる多目的最適化
- 124 フレキシブル継手と円板を用いたポンプ配管系の振動低減対策
- 140 大規模非線形系に対する高性能振動解析手法の開発 : 非線形支持された回転軸系への適用
- 440 動吸振器を用いたパターン形成現象の防止対策 : 多自由度系における効果的なモード毎設計法
- 円形コイルと円柱磁石で構成された磁気ダンパ(機械力学,計測,自動制御)
- ポンプ配管系の振動低減対策--フレキシブル継手と剛体円板を用いる方法について
- Free Vibration Analysis of a Tree Structure by the Transfer Influence Coefficient Method : 2nd Report, Treatment of a Three-Dimensional Tree Structure and Numerical Computational Results
- Free Vibration Analysis of a Tree Structure by the Transfer Influence Coefficient Method : 1st Report, Formulation for a Two-dimensional Tree Structure
- 405 疑似焼き鈍し法と遺伝的アルゴリズムを用いたハイブリッド最適化手法の提案
- Nonlinear Forced Vibration of Roller Chain
- Analysis of Coupled Vibration between Railway Vehicle Wheels and a Rail in Both Vertical and Horizontal Directions Using an Approximate Model with an Infinite Number of Vehicles
- Vibration Control of a Rotating Disk Subjected to a Periodic External Force by Dynamic Absorbers
- Nonlinear Response of Roller Chain to Combined Forcing and Parametric Excitations
- Vibrations of Nonlinear Systems with Discontinuities : The Case of a Preloaded Compliance System
- Nonlinear Free Vibration of Roller Chain Streched Vertically
- On the Static Running Accuracy of Cylindrical Roller Bearings
- Research on the Interaction between Power Source and Machinery : Part 3,Vibrating Lift Made by Utilizing the Principle of Self-Synchronization
- Nonlinear Harmonic and Parametric Resonances of a Roller Chain Stretched Horizontally
- Subharmonic Oscillation of Order 1/3 in Roller Chain : 1st Report, Theoretical Analysis of the System Having Multiple Degrees of Freedom
- C37 非線形共振を利用した並列多重倒立振子の振り上げ制御(OS13 機械における非線形振動2)
- C36 クーロン摩擦により生じる自己同期現象 : 2個の自励振動子を結合した場合(OS13 機械における非線形振動2)
- C31 多自由度非線形振動系に対する楕円型平均法について(OS13 機械における非線形振動1)
- C08 ヤコビの楕円関数に基づく振り子の振動制御 : 直列二重振り子への適用(OS7 機械・機械構造物の耐震・免震・振動制御(1))
- 652 部分空間制御法の応用に関する研究
- 651 並列二重倒立振子の高速移動制御に関する研究
- 331 動吸振器を用いたパターン形成現象の防止対策 : 粘弾性多自由度系に対する実験的検証
- 244 手持ち振動工具への応用に向けた同期振動発生機構の開発 : 4個の振動子を搭載したモデルについての検討
- 243 手持ち振動工具への応用に向けた同期振動発生機構の開発 : 断片線形ばねを用いた衝突モデルについての検討
- 240 大規模非線形系に対する高性能振動解析手法の開発 : 大域的非線形系への適用
- 239 大規模非線形系に対する高性能振動解析手法の開発 : 非比例減衰系への適用
- 220 拡張カルマンフィルタ理論を用いた複数損傷同定解析手法の提案
- 211 摩擦自励振動子群における自己同期現象
- 204 大規模非線形系の高性能振動解析法に対する計算効率・計算精度の検討
- 558 集中系モデルによる非線形圧力波の解析
- F41 集中系モデルによる非線形圧力波の解析 : 分岐管の取扱い及び非線形圧力波に対する低減効果(F4 機械力学(非線形振動・同期化現象))
- F44 自己同期現象を利用した手持ち振動工具の開発(F4 機械力学(非線形振動・同期化現象))
- F42 摩擦力が作用する結合自励振動子群の自己同期現象(F4 機械力学(非線形振動・同期化現象))
- E12 はり構造物に対するフィルタ理論を援用した複数損傷同定解析手法の提案(E1 機械力学(計測・評価))
- Quenching of Frictional Vibration of a Rotating Circular Plate by Dynamic Absorbers
- Self-Excited vibrations of a Rotating Circular Plate : 2nd Report, The Case of a Circular Plate with Internal Resonance : Series C : Vibration Control Engineering Engineering for Industry
- Self-Excited Vibrations of a Rotating Circular Plate : The Case of a Circular Plate without Internal Resonances : Vibration, Control Engineering, Engineering for Industry
- F45 大規模非線形系に対する高性能振動解析手法の開発 : 大域的非線形系への適用(F4 機械力学(非線形振動・同期化現象))
- F43 異なる二つの楕円関数の和を母解とする楕円型平均法(F4 機械力学(非線形振動・同期化現象))
- Vibrations of a Forced Self-excited System with a Retarded Argument : Subharmonic Vibrations of Order 1/2
- On the Subharmonic Vibrations of Order 1/2 of a Nonlinear Vibrating System with a Duffing Type Restoring Characteristic : 2nd Report, Case of Soft Spring
- On the 1/2-th Subharmonic Vibrations of a Non-linear Vibrating System with a Hard Duffing Type Restoring Characteristic
- On the Stability of a Rotating Elastic Shaft Supported by Journal Bearings
- Vibrations of a Forced Self-excited System with Time Lag
- Polygonal Deformation of Roll-Covering Rubber
- Transfer Stiffness Coefficient Method Combined with Concept of Substructure Synthesis Method : Linear Free and Forced Vibration Analyses of a Straight-Line Beam Structure
- An Approximate Model with an Infinite Number of Vehicles for Analysis of Coupled Vibrations Between Railway Vehicle Wheels and Rail in the Vertical Direction
- Coupled Vibrations Between Railway Vehicle Wheels and a Rail : Coupled Vibration Characteristics in the Horizontal Direction Taking Creep Forces into Account
- A Method of Vibrational Analysis Using a Personal Computer (Suggested Transfer Influence Coefficient Method) : Series C : Vibration, Control Engineering, Engineering for Industry
- A Method of Vibrational Analysis Using a Personal Computer (2nd Report, Application of the Transfer Influence Coefficient Method to a Distributed Flexural Vibrational System) : Series C : Vibration, Control Engineering, Engineering for Industry
- Coupled Vibrations between Railway Vehicle Wheels and a Rail : 2nd Report, Axial Steady-state Vibration of a Rotating Wheel
- Coupled Vibrations between Railway Vehicle Wheels and the Rail : 3rd Report, Analysis of Vertical Steady-state Vibrations
- On the Static Running Accuracy of Ball Bearings
- A Method of High Speed Structural Analysis Using a Personal Computer : Comparison with the Transfer Matrix Method
- On the Radial Vibration of Ball Bearings : Computer Simulation
- Coupled Lateral Vibrations between Rail and Railway Vehicle's Wheels Part 1,Equations of Motion of Rail and Its Characteristics
- Method of Preventing Unstable Vibration Caused by Time Delays in Contact Rotating Systems : Application of New Stability Analysis
- Free Vibration Analysis of a Multiple Straight-Line Structure Regarded as a Distributed Mass System by the Transfer Influence Coeflicient Method
- Free Vibration Analysis of a Multiple Straight Line Structure Regarded as a Discrete System by the Transfer Influence Coefficient Method
- Exact Solutions of the Autonomous Duffing Equation and Their Computation : Expression of Solutions and Trial Calculation of a Characteristic Parameter) : Vibration, Control Engineering, Engineering for Industry
- Higher Approximate Solutions of the Duffing Equation : Primary Resonance in the Soft Spring System
- Vibrations of a Forced Self-Excited System with a Retarded Argument : Influence of Initial Conditions
- Nonlinear Response of a Roller Chain to Combined Forcing and Parametric Excitations (4 th Report, Experiment of 1/3-Harmonic and Parametric Combination Resonance -No.2) : Series C : Vibration, Control Engineering, Engineering for Industry
- 1/3-Harmonic and Parametric Combination Resonance of a Roller Chain : Vibration, Control Engineering, Engineering for Industry
- Higher Approximate Solutions of the Duffing Equation : Odd Order Superharmonic Resonances in the Hard Spring System
- On a Method of Higher Approximation and Determination of Stability Criterion for Steady Oscillations in Nonlinear Systems
- Polygonal Wear of Automobile Tire
- Polygonal Wear of Work Rolls in a Hot Leveler of Steel Making Machine
- Vibration of Rotor Based on Ball Bearing : 1st Report, Static Stiffness of Ball Bearing
- Self-excited Vibration of a Circular Plate Subjected to Frictional Forces Exerted in Two Regions on Its Outer Circumference : Part 2, The Case of a Circular Plate with a Effect of Internal Resonances
- Self-excited Vibration of a Circular Plate Subjected to Frictional Forces Exerted in Two Regions on Its Outer Circumference : Part 1, The Case of a Circular Plate without Effect of Internal Resonances
- Self-excited Vibration of a Circular Plate Subjected to Frictional Forces Exerted in Two Regions on Its Outer Circumference : The Case of a Circular Plate Subjected to Distributed Frictional Forces without the Effect of Internal Resonances
- Pattern Formation Generated in a Winder System of Textile Machine(Special Issue on Nonlinear Dynamics)
- 221 摩擦力が作用する自励振動子群に生じる自己同期現象 : 振動子間のエネルギーの授受に関する検討(自励・鳴き振動,OS-1 振動基礎,総合テーマ「伝統を,未来へ!」)
- 118 ハイブリッド手法による骨組構造物の位相と形状の同時最適化
- 547 パレート最適解のグループ化を用いたハイブリッド最適化手法(動力学問題の最適設計とその周辺技術と応用,OS-14 動力学問題の最適設計・制御とその周辺技術と応用,総合テーマ「伝統を,未来へ!」)
- 356 動吸振器を用いたパターン形成現象に対する防止対策 : 構造変更を考慮した設計法(パターン形成現象,OS-20 パターン形成現象と複雑性,総合テーマ「伝統を,未来へ!」)
- 355 動吸振器を用いたパターン形成現象に対する防止対策の実験的検証(パターン形成現象,OS-20 パターン形成現象と複雑性,総合テーマ「伝統を,未来へ!」)
- 271 集中系モデルによる弾性管内非線形圧力波の解析(圧力脈動・燃焼振動のメカニズム,OS-22 流体関連振動・音響メカニズムと計測制御,総合テーマ「伝統を,未来へ!」)
- 241 大規模非線形系に対する高性能振動解析手法の開発 : 効率的な高次モード消去法(解析,OS-21 機械・構造物における非線形振動とその応用,総合テーマ「伝統を,未来へ!」)
- 238 手持ち振動工具に向けた同期振動発生機構の開発 : 4振動子衝突モデルによる実験的検討(衝突(2),OS-21 機械・構造物における非線形振動とその応用,総合テーマ「伝統を,未来へ!」)
- On the Static Running Accuracy of Ball Bearings : 2nd Report, Results and Discussion
- Optimum Design of Rotating Machine with Overhung Weight : Part 2, Numerical and Experimental Results
- Optimum Design of Rotating Machines with Overhung Weight : Part 1, Formulation of Optimum Problems