Preparation of PbTi0_3 Thin Films by Screen Printing Method
スポンサーリンク
概要
- 論文の詳細を見る
PbTiO3 thin films were obtained by the screen printing method on Au bottom electrodes using Si(1OO) sub-strates. The screen-printable paste was synthesized from the Pb-Ti complex alkoxide and abietic acid. The optimum conditions of amount of PbO content in the paste and annealing temperature were investigated to prepare the ferroelectric thin film. The remanent polarization and coercive field of this thin film were 8 μC/cm^2 and 110kV/cm, respectively. Pyroelectric coefficient was 0.67 × 10^-8(C/am^2・K) after poling.
- 社団法人応用物理学会の論文
- 1994-12-15
著者
-
Tanino Katsumi
Toyama Industrial Technology Center
-
FUTAKUCHI Tomoaki
Toyama Industrial Technology Center
-
Futakuchi Tomoaki
Toyama Industrial Techcnology Center
関連論文
- Preparation of Ba(Ti, Zr)O_3 Thick Films by Screen Printing
- Preparation of Dielectric Thin Films of Pb[(Mg_Nb_)_Ti_]O_3 by Screen Printing Method
- Development of SnO_2-based Gas Sensors for Detection of Volatile Organic Compounds
- Migration of Conductive Ink using Silver-Cooper Solid Solution Powder
- Preparation of PbTi0_3 Thin Films by Screen Printing Method
- Low-Temperature Mixed Sintering of Pb(Zr_Ti_x)O_3-Pb(Zn_Nb_)O_3 Ceramics and Their Pyroelectric Properties
- Low-Temperature Sintering of Pb(Mg_Nb_)O_3-PbTiO_3 Ceramics with Addition of PbO-Bi_2O_3
- Simple and Low-Cost Fabrication of Flexible Capacitive Tactile Sensors
- Preparation of Textured BaTiO3 Thick Films by Screen Printing
- Preparation of (Ba,Sr)TiO3 Thick Films with Ni Electrodes by Screen Printing
- Preparation of PbZrO_3 -PbTiO_3 -Pb(Mg_Nb_)O_3 Thick Films by Screen Printing
- Preparation of Piezoelectric Ceramic Transformer Operating in Bending Vibration Mode
- Preparation of 0.92PbZrO_3-0.03PbTiO_3-0.05Pb(Zn_Nb_)O_3 Pyroelectric Thick Films by Screen Printing
- Preparation of Ferroelectric Thick Film Actuator on Silicon Substrate by Screen-Printing
- P2-66 Evaluation of Piezoelectric Power Generator using Barium Titanate Based Ceramics(Poster session 2)
- Low-Temperature Preparation of Lead-Based Ferroelectric Thick Films by Screen-Printing
- Preparation of BaTiO3 Thick Films by Inkjet Printing on Oxygen-Plasma-Modified Substrates
- Cross-Section Analysis by Electron Backscatter Diffraction of Textured BaTiO3 Thick Films Prepared by Screen Printing
- Trapping and Collection of Lymphocytes Using Microspot Array Chip and Magnetic Beads
- Preparation of Ba(Ti,Zr)O3 Thick Films on Silicon Substrate by Screen Printing
- Preparation of (Ba,Sr)TiO3 Thick Film on ZrO2 Substrates by Inkjet Printing
- Preparation of Ba(Ti,Zr)O3 Thick-Film Microactuators on Silicon Substrates by Screen Printing
- Electric Properties of [(BaO)1.00(XO)x](Ti0.95Zr0.05)O2 ($\textit{X} = \text{Ca}$, Sr, Ba) Ceramics Fired under Reduced Atmosphere
- Preparation of ($1-x$)(Ba,Sr)TiO3–$x$MgTiO3 Based Thick Films by Inkjet Printing
- Fabrication Technique for Preparing Nanogap Electrodes by Conventional Silicon Processes