切りくずかみこみによるホブ切れ刃損傷と対策(機械要素,潤滑,工作,生産管理など)
スポンサーリンク
概要
- 論文の詳細を見る
The simulation program developed in the former report that calculates the clearance between cutting edge of hob and tooth flank of gear blank is applied to some practical industrial problems of dry hob cutting, i.e. chipping failure of cutting edge of carbide hob and bad coarse surface finish of hobbed tooth flank of product gears. The output of the simulation explains the mechanism of such actual failures in detail. The "Distance of Single Edge Cutting" of a hob tooth is proposed to be an index of pinching and crushing of chips intruded into the clearance between hob cutting edge and tooth flank of gear blank. Influencing factors on it is investigated and the bases for finding countermeasures are shown. This method has been applied to some practical cases of problem in mass-production of automotive gears, and good result was confirmed.
- 一般社団法人日本機械学会の論文
- 2003-05-25
著者
-
小森 雅晴
京都大学大学院工学研究科
-
小森 雅晴
京都大学 大学院工学研究科 機械理工学専攻
-
久保 愛三
京都大学大学院工学研究科
-
角 昌興
岐阜ギヤー工業(株)
-
角 昌興
京都大学大学院工学研究科
-
Kubo Akihiko
Department Of Mechanical Engineering Kitami Institute Of Technology
-
小森 雅晴
京都大学大学院 工学研究科
関連論文
- 3136 ウェッジアーティファクトを用いたギヤチェッカー検査法(S34-4 伝動装置の基礎と応用(4) 歯車の形状解析,ラック&ピニオン,その他,21世紀地球環境革命の機械工学:人・マイクロナノ・エネルギー・環境)
- 2209 検査校正用高精度ピッチアーティファクトの開発(歯車の設計・性能評価,一般講演)
- (15)中凸形に歯面形状を修整した歯車の振動の一般特性 : 第1報,かみあいの一般化モデルの提案(論文,日本機械学会賞〔2008年度(平成20年度)審査経過報告〕)
- 歯車の歯の側端や歯先稜の接触による損傷 : 第4報,歯の弾性変形に起因するトロコイド干渉による損傷(機械要素,潤滑,工作,生産管理など)
- 歯車の歯の弾性変形に起因するトロコイド干渉による損傷(O.S.02-4 歯車の強度(4))
- 歯車計測と標準
- 歯車運動伝達 : 伝達誤差とその低減(はじめての精密工学)
- 歯車・動力運動伝達装置における日本の有力技術(これが世界一!日本の技術力)
- 314 検査校正用高精度ピッチアーティファクトの研究(OS05-1 歯車の検査I)
- 中凸形に歯面形状を修整した歯車の振動の一般特性 : 第2報,歯面形状偏差の影響(機械要素,潤滑,工作,生産管理など)