Tandem Electron Beam Welding (Report IX) : High Speed Tandem Electron Beam Welding(Physics, Process, Instrument & Measurement)
スポンサーリンク
概要
- 論文の詳細を見る
High speed wilding up to 15m/min on SUS304 steel of 3mmt was achieved by Tandem Electron Beam welding method. Sound bead without undercut, underfill, humping, overlap and spattering was obtained. Up to the welding speed of 15m/min, welding characteristics in single electron beam welding were revealed for SUS304 stainless steel of 3mmt. Welding defects such as undercut, underfill, humping and overlap occurred according to increasing welding speed. All defects were suppressed by Tandem Electron Beam welding with proper power ratio, Tandem Gap and oscillation of the second beam. Effect of Tandem parameters on bead appearance was investigated.
- 大阪大学の論文
著者
-
Arata Y
Osaka Univ. Osaka Jpn
-
TOMIE Michio
Osaka University
-
ABE Nobuyuki
Osaka University
-
ARATA Yoshiaki
Osaka University
-
Tomie Michio
Kinki University
-
Abe Nobuyuki
Osaka Univ. Osaka Jpn
-
Abe Nobuyuki
Joining And Welding Research Institute Osaka University
関連論文
- Crystal Growth of Rare Earth Pnictides and ZnSe in W and Mo Crucible closed by Electron Beam Welding(Physics, Process, Instruments & Measurements)
- High Speed Welding of Thick Plates using a Laser-Arc Combination System(Physics, Processes, Instruments & Measurements)
- Effect of Laser Beam Irradiation on CO_2 Gas Arc Welding
- Transient Arc Diagnosis with OMA(Welding Physics, Processes & Instruments)
- Pulsed High Current Heating of a Microwave Plasma at Atmospheric Pressure
- High Power Microwave Plasma Beam as a Heat Source (Report IV) : Application to Cutting
- Welding of Aluminum Alloy with High Power Direct Diode Laser(Physics, Processes, Instruments & Measurements)
- Effect of Neutron Irradiation on Strength of Electron Beam Welded Joint of JFMS Steel for Fusion Reactor(Materials, Metallurgy & Weldability)
- Strength of Candidate Materials for Nuclear Fusion Reactor and Their Electron Beam Welded Joint at Cryogenic Temperature(Mechanics, Strength & Structural Design)
- Effects of Horn Connected with Gas Tunnel Type Plasma Spraying Torch
- Gas Tunnel Type Plasma Spraying Apparatus(Welding Physics, Process & Instrument)
- Transferred Type Plasma Jet Using Gas Tunnel(Welding Physics, Process & Instrument)
- Production of ECR Mirror Plasma by High Power Millimeter-Wave Radiation : Nuclear Science, Plasmas and Electric Discharges
- ECR Plasma in a High Power Millimeter-Wave Beam (Report IV) : Contribution of Higher Harmonic Resonance Heating(Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report III) : Difference in Plasma Property by Axial and Radial Launches(Welding Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report II) : Time Variation of Electron Density(Welding Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report 1)(Welding Physics, Process & Instrument)
- Electron Beam Melting of Aluminum Alloy by Beam Oscillation(Physics, Process, Instrument & Measurement)
- 06-P-12 Effect of Electrical Properties and Microstructures of Pb(Zr, Ti)O_3 Thick Films Prepared by Aerosol Depoisition on CO_2 Laser Radiation
- Dynamic Observation of Beam Hole during Electron Beam Welding in Carbon Steel(Welding Physics, Process & Instrument)
- Tandem Electron Beam Welding (Report V)(Welding Physics, Processes & Instruments)
- Electric Field Assisted Treatment of Various Plasma Sprayed ZrO_2 Coatings(Physics, Process, Instruments & Measurements)
- Influence of Plasma Spray Conditions on the Structure of Al_2O_3 Coatings(Surface Processing)
- Porosity Measurement of Ceramic Coating by Image Processing Method(Physics, Process, Instrument & Measurement)
- Fracture Behavior of Plasma Sprayed Ceramic Coatings in Scratch Test(Physics, Process, Instrument & Measurement)
- Effect of Spraying Condition on Ceramic Coating Quality in Gas Tunnel Type Plasma Spraying(Physics, Process, Instrument & Measurement)
- Study on the Strength of Explosive Plugged Part under the Environment of Steam Generator
- Uber Eigenschaften von Stopselteil Explosiver Haftung durch WarmestoB(Mechanics, Strength & Structural Design)
- Research on Characteristics of Filler Metal and Flux Influencing on the Toughness of a Carbon Steel Weld : Minor Elements and Alloying Elements Influencing on the Toughness of Weld(Materials, Metallurgy & Weldability)
- Characteristics of Metal Electroplating to Plasma Sprayed Ceramic Coatings(Physics, Process, Instrument & Measurement)
- Struktur der Al_2O_3 Schichten nach dem Gas Tunnel Plasma-Spritzgerat(Physics, Process, Instrument & Measurement)
- Untersuchungen der SchweiBguteigenschaften in Abhangigkeiten vom Basizitatsgrad der 50kg/mm^2 Grad agglomerierten UP-SchweiBpulver(Materials, Metallurgy & Weldability)
- Deposit Characteristics of Sprayed Powder by Gas Tunnel Type Plasma Spraying Apparatus(Physics, Process & Instrument)
- Basic Studies on Plasma Sprayed Ceramics Coatings (Report 1) : Erosion Mechanism at ACT-JP Process(Materials, Metallurgy & Weldability)
- Dynamic Characteristics of Variable Frequency Pulsed TIG Arc(Welding Physics, Process & Instrument)
- Basic Characteristics of Gas Tunnel Type Plasma Jet Torch
- Experimental Study on Dynamic Properties of Power Sources for MIG/MAG Welding(Welding Physics, Process & Instrument)
- Pressure Distribution and Basic Properties of Gas Tunnel Type Plasma Jet Torch(Welding Physics, Process & Instrument)
- Saturation Behavior of Balmer-Line Fluorescences in a Hydrogen Plasma
- Impact Property at Cryogenic Temperature of Candidate Materials for Fusion Reactor and Their Electron Beam Welded Joints(Materials, Metallurgy & Weldability)
- Effect of Neutron Irradiation on Cryogenic Temperature Strength of Aluminum Alloys and Their Electron Beam Welded Joints(Mechanics, Strength & Structural Design)
- Hydroxyapatite Film Formation by Aerosol Deposition Method(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Formation of Functional Ceramic Films with Ultrafine Particle Beams
- Weldability of 18%Ni Maraging Steel (HT 210) by Ultra High Voltage Electron Beam Welding(Materials, Metallurgy & Weldability)
- Bonding of Al_2O_3 to SS41 Steel with LPC Plasma Sprayed Cu-Ti Two-layer Coatings(Surface Processing)
- Suppression Mechanism of Overlapping Defects in High Speed TEB Welding
- High Speed Welding of Thin Stainless Steel Plates by Tandem Electron Beam
- Bending Strength of CO_2 Laser Welded Joints of 87-0X1.20980BFF1F4DP+0l_2O_3 Ceramics
- High Power CO_2 Laser Welding of Al_2O_3 Ceramics(Physics, Process, Instruments & Measurements)
- Photoresponse of Plasma Sprayed TiO_2-Rutile Semiconductor(Physics, Process, Instruments & Measurements)
- Formation of YBaCu-O System Superconductor by Thermal Spraying(Materials, Metallugy & Weldability)
- Photoanodic Properties of Plasma Sprayed TiO_2 Coatings(Surface Processing)
- Characteristics of 500kV Ultra-High Voltage Electron Beam Heat Source (Report II) : Deep Penetration by Flat Position Welding(Physics, Process, Instruments & Measurement)
- Electrical Conductivity of Titanium Oxide (Rutile) Plasma Sprayed Coatings(Physics, Process, Instrument & Measurement)
- Tandem Electron Beam Welding (Report IX) : High Speed Tandem Electron Beam Welding(Physics, Process, Instrument & Measurement)
- High Power CO_2 Laser Cutting and Welding of Ceramics(Physics, Process, Instrument & Measurement)
- Characteristics of 600kV Class Ultra High Voltage Electron Beam Heat Source(Physics, Process, Instrument & Measurement)
- Plasma Sprayed Y-Ba-Cu-O System Superconductor
- Solid-State Reaction Bonding of Alumina to Cu-4Ti Alloy(Materials, Metallurgy & Weldability)
- Shape Decision of High Energy Density Beam
- Das Laser-Schweissen von Aluminium und Alu-Legierungen
- Some Problems on Laser Plasma Control with Argon Assist Gas
- Fundamental Phenomena in High Power CO_2 Laser (Report II) : Vacuum Laser Welding(Welding Physics, Process & Instrument)
- Fundamental Phenomena in High Power CO_2 Laser Welding (Report I) : Atmospheric Laser Welding(Welding Physics, Process & Instrument)
- Surface Modification of TiO_2-ZrO_2 Layers with Direct Diode Laser(Physics, Processes, Instruments & Measurements)
- Deposition of Hydroxyapatite Film on Titanium by Ultra-fine Particle Beam(Physics, Processes, Instruments & Measurements)
- Materials Processing with High Power Diode Lasers(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Laser Forming of Thick Steel Plates by a 2kW Diode laser with a Kaleidoscope(Physics, Processes, Instruments & Measurements)
- 100KW Klasse-Elektronenstrahlen-SchweiBtechnologie (Bericht II) : Charakterristik der SchweiBraupen und deren Analyse
- Some Properties of 30KW-Class Electron Beam for Welding
- Interfacial Phenomena During Field Assisted Bonding of Zirconia to Metals
- Electron Beam Welding of Zirconium Plate
- Effect of Beam Oscillation on Electron Beam Melting
- Improvement of Sprayed Coatings with Ultra High Voltage EB Melting
- Properties of ECR Plasma in a Simple Mirror Field II : Spatial Structure of the Plasma
- Properties of ECR Plasma in a Simple Mirror Field I : Correlation in Cold and Hot Electron Production
- Effect of Plasma Opacify on the Doppler-Free Polarization Spectrum in a Hydrogen Plasma
- Laser-Induced Fluorescence and Doppler-Free Polarization Spectra in a Low Density Hydrogen Plasma
- Structure of ECR Mirror Plasma(Welding Physics, Process & Instrument)
- Measurement of Soft X-ray from Hot Electron Plasma in a Magnetic Field(Welding Physics, Process & Instrument)
- Thermal Plasma Diagnostics Using Tunable Dye Laser (Report III)(Welding Physics, Process & Instrument)
- Thermal Plasma Diagnostics Using Tunable Dye Laser (Report II)(Welding Physics, Process & Instrument)
- Multichannel Measurement of Soft X-ray with MCP and OMA System(Welding Physics, Process & Instrument)
- Thermal Plasma Diagnostics Using Tunable Dye Laser (Report I) : Resonance Fluorescence in a High Power Microwave Discharge(Welding Physics, Process & Instrument)
- Two-Dimensional Multichannel Spectroscopy of a Pulsed Arc
- Tandem Electron Beam Welding (Report VII)(Welding Physics, Process & Instrument)
- Tandem Electron Beam Welding (Report VI) : Spatterless Welding of SUS 304(Welding Physics, Process & Instrument)
- 100KW Class Electron Beam Welding Technology (Report III) : Characteristics of Deep Penetration Bead and its Analysis
- Tandem Electron Beam Welding (Report VIII) : Control of Molten Metal Flow(Physics, Process, Instrument & Measurement)
- Electron Beam Cladding of Cu Foil on Carbon Steel Plates
- 100-KW Class Electron Beam Welding Technology (Report I) : Welding Apparatus and Some Aspects as A Heat Source
- 100kW Class Electron Beam Welding Technology (Report IV) : Fundamental Research on Horizontal Electron Beam Welding(Welding Physics, Processes & Instruments)
- Formation of Fine Particles of Tungsten by Electron Beam
- Mechanical Properties of Electron Beam Welds of Heavy Section Steel Plates(Materials, Metallurgy & Weldability)
- Some Problems of the Weldability of High Strength Thick Plate Steels Subjected to Electron Beam Welding(Materials, Metallurgy & Weldability)
- Mechanical Properties of Electron Beam Welds of Centrifugal Casting Steel Plates(Materials, Metallurgy & Weldability)
- Crystal Growth of Rare-Earth Compounds with Tungsten Crucible Welding by Electron Beam(Physics, Process, Instrument & Measurement)
- Electron Beam Cladding of Titanium on Stainless Steel Plate(Physics, Process, Instrument & Measurement)
- Laser Surface Modification of Stainless Steel : Alloying with Molybdenum(Physics, Process, Instruments & Measurements)
- Observation of Molten Metal Flow during EB Welding(Physics, Process & Instrument)