Surface Hardening of Various Metals and Alloys with Boronizing Technique(Materials, Metallurgy & Weldability)
スポンサーリンク
概要
- 論文の詳細を見る
By means of boronizing technique in argon atmospheric furnace at 950-1000℃ with boron powder, probability of surface hardening has been investigated for various reactive, refractory, ferrous and nonferrous and heat-resistant metals and alloys in commercial use. Surface hardening was possible for all these metals and alloys used. Maximum hardness on surface of most metals and alloys represented more than VHN1000. Moreover hardness distribution and microstructure in crosssectional area, and X-ray analysis of boronized layer were investigated. These results indicated the introduction for further investigation for boronizing technique of various new alloys which will be developed.
- 大阪大学の論文
著者
-
NAKATA Kazuhiro
Osaka university
-
MATSUDA Fukuhisa
Osaka University
-
Nakata Kazuhiro
Osaka Univ. Ibaraki
-
TOHMOTO Kenji
Osaka University
-
Matsuda Fukuhisa
Osaka Univ.
関連論文
- Metal Vapor Behavior in GTA Welding of a Stainless Steel Considering the Marangoni Effect
- Visualization of fume generation process in arc welding with numerical simulation
- Effect of Hydrogen Content on Cold Crack Susceptibility of Various Steels with the Implant Test
- Fractography of Cold Crack of Various Carbon Steels and Alloy Steels by Means of the Implant Test : Studies on Fractography of Welded Zone (IV)
- Contraction Process and RRC Test of Nodular Graphite Cast Iron Weldments : Studies on the Weld Cracking of Nodular Graphite Cast Iron (Report 5)
- Preheating Effect on the Critical Rupture Stress of Nodular Graphite Cast Iron Welds : Study on the Weld Cracking of Nodular Graphite Cast Iron (Report 2)
- Estimation of Cracking Susceptibility of Nodular Graphite Cast Iron by the Implant Test : Study on the Weld Cracking of Nodular Graphite Cast Iron (Report 1)
- Toughness Improvement of the HAZ for Machine Structural Carbon and Low Alloy Steels (Report 4) : Effect of PWHT on the Absorbed Energy of HAZ for Medium, High Carbon Machine Structural Steels(Materials, Metallugy & Weldability)
- New Aspects of Sensitization Behavior in Recent 316 Type Austenitic Stainless SteelsAustenitic Stainless Steels(Materials, Metallurgy & Weldability)
- Microstructural Investigations on Decomposition Behaviour of M-A Constituent and Recovery of Ductility due to PWHT in Simulated HAZ of HSLA Steels(Materials, Metallugy & Weldability)
- Friction Stir Welding of Copper and Copper Alloys(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Mechanical Properties on Electron Beam Welds of Constructional High Tension Steels (Report V)
- Effect of Tool Plunging Downforce on Friction Stir Welding of ADC12 Die Cast Alloy(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Dissimilar Metal Joining of Steel to Aluminum by Lap Joint MIG Arc Brazing(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Pulsed GMAW : Spattering in Pulsed CO_2 Welding(Welding Physics, Process & Instrument)
- Metal Transfer Characteristics in Self-shielded Flux Cored Arc Welding for Mild Steel and 50kgf/mm^2 Class Tensile Steel (Report II) : Effects of Some Key Elements in Flux on Metal Transfer and Feasibility of Welding(Welding Physics, Process & Instrument)
- Metal Transfer Characteristics in Self Shielded Flux Cored Arc Welding for Mild Steel and 50kgf/mm^2 Class Tensile Steel (Report I) : Metal Transfer Mode and Feasibility of Welding(Welding Physics, Process & Instrument)
- GMA Welding of 9%Ni-Steel with Similarly Composed Nickel Alloy Wire in Helium Shielding
- Arc Characteristics and Metal Transfer for Flux-Cored Electrode in GMA Welding (Report II)(Welding Physics, Processes & Instruments)
- Arc Characteristics and Metal Transfer with Flux-Cored Electrode in CO_2 Shielding (Report I) : Effect of Geometrical Shape in Wire Cross-section on Metal Transfer in Stainless Steel Wire(Welding Physics, Processes & Instruments)
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report III) : Effect of Straining Rate on Crack Length in Weld Metal
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report II) : Effect of Straining Rate on Cracking Threshold in Weld Metal during Solidification
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report I) : Characteristics of Ductility Curves during Solidification by Means of the Trans-Varestraint Test
- Effect of Solidification Rate on Solidification Structure in Weld Metal
- Additional Note on the Report "Quench Hardening and Cracking in Electron Beam Weld Metal of Carbon and Low Alloy Hardenable Steels"
- Quench Hardening and Cracking in Electron Beam Weld Metal of Carbon and Low Alloy Hardenable Steels
- Quantitative Evaluation of Solidification Brittleness of Weld Metal during Solidification by In-Situ Observation and Measurement (Report II) : Solidification Ductility Curves for Steels with the MISO Technique(Materials, Metallurgy & Weldability)
- Quantitative Evaluation of Solidification Brittleness of Weld Metal during Solidification by Means of In-Situ Observation and Measurement (Report I) : Development of the MISO Technique(Materials, Metallurgy & Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report IX) : Effect of Titanium on Solidification Crack Resistance(Materials, Metallurgy & Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VIII) : Effect of Nitrogen on Cracking in SUS 304 Weld Metal(Materials, Metallurgy & Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VII) : Effect of Mn and N on Solidification Crack Resistance(Materials, Metallurgy & Weldability)
- Weld Metal Cracking and Improvements of 25%Cr-20%Ni (AISI 310S) Fully Austenitic Stainless Steel
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VI) : Effect of La or REM Addition on Solidification Crack Resistance(MATERIALS METALLURGY AND WELDABILITY)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report V) : Solidification Crack Susceptibility and Amount of Phosphide and Sulphide in SUS 310S Weld Metals
- A New Explanation for Role of Delta-Ferrite Improving Weld Solidification Crack Susceptibility in Austenitic Stainless Steel(Materials, Metallurgy, Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report IV) : Effect of Decreasing P and S on Solidification Crack Susceptibility of SUS 310S Austenitic Stainless Steel Weld Metals
- Fractographic Investigation on Solidification Crack in the Varestraint Test of Fully Austenitic Stainless Steel : Studies on Fractography of Welded Zone (III)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report III) : Effect of Strain Rate on Cracking Threshold in Weld Metal during Solidification
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report II) : Effect of Ferrite, P, S, C, Si and Mn on Ductility Properties of Solidification Brittleness
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report I) : Fundamental Investigation on Solidification Behavior of Fully Austenitic and Duplex Microstructures and Effect of Ferrite on Microsegregation
- Effect of Grain Morphology on Consumption of GTA Electrode(Physics, Process, Instruments & Measurements)
- Gas-Tungsten-Electrode (Report 4) : Measurement of Cathode Temperature(Physics, Process, Instrument & Measurement)
- Gas-Tungsten-Electrode (Report 5) : Effect of Combined Additives of Rare Earth Metal Oxides on Arc Characteristics of Tungsten Electrode(Physics, Process, Instrument & Measurement)
- Behavior of Rare Earth Metal Oxides during Arcing(Physics, Process, Instrument & Measurement)
- Direct Observation of Cathode Surface : Gas-Tungsten-Arc Electrode (3)(Physics, Process, Instrument & Measurement)
- Oxidation Behaviour and Rim Formation Mechanism of Tungsten Electrode(Physics, Process, Instrument & Measurement)
- Gas-Tungsten-Arc Cathode and Related Phenomena
- The VDR Cracking Test for Solidification Crack Susceptibility on Weld Metals and Its Application to Aluminum Alloys(Materials, Metallurgy, Weldability)
- Effect of Electromagnetic Stirring on Weld Solidification Structure of Aluminum Alloys (Report I) : Investigation on GTA Weld Metal of Thin Sheet
- Combined Effect of Current Pulsation and Zr Addition on Improvement of Solidification Cracking of Al-Zn-Mg Alloy Weld Metal : Effect of Additional Element on Weld Solidification Crack Susceptibility of Al-Zn-Mg Alloy (Report IV)(Materials, Metallurgy & We
- Hydrogen Embrittlement of SUS 316 Austenitic Stainless Steel Weldments(Materials, Metallurgy & Weldability)
- Effect of Additional Element on Weld Solidification Crack Susceptibility of Al-Zn-Mg Alloy (Report III) : Enhancement of Beneficial Effect of Zirconium on Improvement of crack susceptibility by Application of Electromagnetic Stirring(Materials, Metallurgy
- Effect of Additional Element on Weld Solidification Crack Susceptibility of Al-Zn-Mg Alloy (Report II) : Results of Weld Crater and Bead Cracking Tests(Materials, Metallurgy & Weldability)
- Effect of Additional Element on Weld Solidification Crack Susceptibility of Al-Zn-Mg Alloy (Report I) : Results of Ring Casting Cracking Test(Materials, Metallurgy & Weldability)
- Assessment of Solidification Cracking Test for Aluminum Alloy Welds(MATERIALS METALLURGY AND WELDABILITY)
- Comparison of Weld Crack Susceptibility of Recent Aluminum Alloys
- New Al-7%Mg Welding Electrode for Crackles Welding of Al-Zn-Mg(7NO1) High Strength Aluminum Alloy (Report I) : Investigation on Weld Solidification Crack Susceptibility(Materials, Metallurgy, Weldability)
- Weldability of Molybdenum and Its Alloy Sheet (Report II) : Ductility of EB and GTA Welds(Materials, Metallurgy, Weldability)
- Weldability of Molybdenum and Its Alloy Sheet (Report I)(Materials, Metallurgy, Weldability)
- Effects of Current Pulsation on Weld Solidification Structure of Aluminum Alloys
- Effect of Electromagnetic Stirring on Weld Solidification Structure of Aluminum Alloys (Report II) : Investigation on GTA in DCSP Weld Metal of 8mm Thick Plate
- Surface Hardening of Various Metals and Alloys with Boronizing Technique(Materials, Metallurgy & Weldability)
- Surface Hardening of Gold with Boronizing Technique(Materials, Metallurgy & Weldability)
- Ion Nitriding Hardening of Non Ferrous Alloys (Report I)(Materials, Metallurgy & Weldability)
- Surface Hardening of Copper-Nickel Alloys with Boronizing(Materials, Metallurgy & Weldability)
- Pulsed CO_2 Arc Welding
- Corrosion Behavior of Tentative Nickel Binary and Ternary Alloys after Plasma Ion Nitriding Treatment : Studies on Surface Modification of Non Ferrous Metals by means of Plasma Ion Nitriding (PIN) Process (Report 3)(Materials, Metallurgy & Weldability)
- Surface Hardening of Ni Alloys by Means of Plasma Ion Nitriding (PIN) Process (Report II) : Effect of Alloying Elements on Surface Hardening(Materials, Metallurgy & Weldability)
- Surface Hardening of Ni Alloys by Means of Plasma Ion Nitriding (PIN) Process (Report 1)(Materials, Metallurgy & Weldability)
- Surface Hardening of Ni-base Alloys with Boronizing Technique(Materials, Metallurgy & Weldability)
- Rapid Plasma Nitriding Process by Means of Hollow Cathode Glow Discharge(Materials, Metallurgy & Weldability)
- Feasibility Study of Ferrous Powder Thermal Spray Coatings on Cylinder Bores in Diesel Engines
- MIG Arc Welding of Magnesium Alloy(Physics, Processes, Instruments & Measurements, INTERNATIONAL SYMPOSIUM OF JWRI 30TH ANNIVERSARY)
- Friction Stir Welding of Mg-Al-Zn Alloys(Physics, Processes, Instruments & Measurements)
- Friction Stir Welding of 6061 Metal-Matrix Composite
- Weldability of High Strength Aluminum Alloys by Friction Stir Welding
- Laser Cladding of TiC Dispersed Ni-Cr Composite Layer on Carbon Steel
- Numerical Computation of Arc Pressure Distribution(Welding Physics, Process & Instrument)
- Melting Phenomena of Flux Cored Wire(Welding Physics, Process & Instrument)
- Effect of Surface Coating around Tungsten Electrode on Formation of "Rim"
- Gas-Tungsten-Arc Electrode (Report 2) : Measurement of cathode temperature(Welding Physics, Process & Instrument)
- New Sintered Electrode of Ir-Y_2O_3 System for Air-Plasma Cutting(Materials, Metallurgy & Weldability)
- New Cathode Material for Air-Plasma Cutting (Report IV) : Direct Observation of Cathode Surface Erosion Process(Physics, Process, Instrument & Measurement)
- New Cathode Material for Air-Plasma Cutting (Report III) : Effect of Thermal and Electric Properties of Ru-Y_2O_3 on Electrode Consumption(Physics, Process, Instruments & Measurement)
- New Cathode Material for Air-Plasma Cutting (Report II) : Effect of Sintering Temperature on Electrode Consumption(Physics, Process, Instrument & Measurement)
- New Cathode Materials for Air-Plasma Cutting(Materials, Metallurgy & Weldability)
- Evaluation of Transformation Expansion and Its Beneficial Effect on Cold Crack Susceptibility Using y-Slit Crack Test Instrumend with Strain Gauge(Materials, Metallurgy & Weldability)
- Observations of Cathode Spot Movement in AC-GTA Welding of Aluminum Alloy(Physics, Process, Instrument & Measurements)
- Plasma Nitriding Behavior on Surface Hardening of Copper-Contained High Tensile Steel(Physics, Processes, Instruments & Measurements)
- Evaluations of Ductility Characteristics and Cracking Susceptibility of Al Alloys during Welding(Materials, Metallurgy & Weldability)
- Carbide Addition on Aluminum Alloy Surface by Plasma Transferred Arc Welding Process(Surface Processing)
- Plasma Carburizing of Tungsten(Physics, Processes, Instruments & Measurements)
- Nd: YAG Laser Weldability of Al-Cu-Si-Mg High Strength Al Alloy(Physics, Processes, Instruments & Measurements)
- Surface Hardening Technology for Aluminum Alloy by Plasma Arc Alloying Process
- Improvement of Wear Resistance of Aluminum Alloy Surface by Forming Si Alloyed Layer with PTA Process(Physics, Process, Instruments & Measurements)
- Ion-Nitriding after Welding Improves SCC (Stress Corrosion Cracking) Resistance of Stainless Steel Weldments
- A New Self-Restrained Solidification Crack Susceptibility Test for Electron-Beam Welding of Aluminum Alloys : Taper-Shaped Hot Cracking Test
- Effect of Rhenium and Niobium on Weld Metal Ductility of Molybdenum by EB Welding : Weldability of Molybdenum and Its Alloy Sheet (Report III)(Materials, Metallurgy & Weldability)
- Observation of arc phenomena in plasma GMA welding process
- Numerical Analysis of Metal Vapor Behavior with Multi-diffusion System in TIG Welding of Stainless Steel