Implementation of ASIC for Monitoring and Control Unit in Intelligent Electrical Apparatus (国際セッションIS-EMD2005) -- (Signal Transmission and Optical Connectors)
スポンサーリンク
概要
- 論文の詳細を見る
This paper presents the ASIC implementation for monitoring and control unit in intelligent electrical apparatus. Based on the analysis of its function, the parallel structure of ASIC is put forward. Function modules of ASIC are described and implemented using VHDL, which include data acquisition module, data processing module, protection module, and interface module utilizing address, data and control buses. On-chip bus is designed to connect all function modules. In order to improve the whole performance of the ASIC, optimizing methods are used. The result of hardware verification based on FPGA indicates that design is correct.
- 社団法人電子情報通信学会の論文
- 2005-11-11
著者
-
Wang Jing
The State Key Laboratory Of Electrical Insulation And Power Equipment Xi'an Jiaotong University
-
Geng Yingsan
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University
-
Geng Yingsan
State Key Laboratory Of Electrical Insulation And Power Equipment (xi'an Jiaotong University)
-
Wang Jianhua
State Key Laboratory Of Electrical Insulation And Power Equipment (xi'an Jiaotong University)
-
Song Zhengxiang
State Key Laboratory of Electrical Insulation and Power Equipment (Xi'an Jiaotong University)
-
Hu Xiaojing
State Key Laboratory of Electrical insulation and Power Equipment (Xi'an Jiaotong University)
-
Guo Jiajia
State Key Laboratory of Electrical insulation and Power Equipment (Xi'an Jiaotong University)
-
Song Zhengxiang
State Key Laboratory Of Electrical Insulation And Power Equipment Xi'an Jiaotong University
-
Hu Xiaojing
State Key Laboratory Of Electrical Insulation And Power Equipment (xi'an Jiaotong University)
-
Guo Jiajia
State Key Laboratory Of Electrical Insulation And Power Equipment (xi'an Jiaotong University)
-
Geng Yingsan
Xi'an Jiaotong Univ. Xi'an Chn
関連論文
- Modeling of the Combination Wave Generator and Simulation of the Surge Immunity Test
- A New Design of Arc Chamber to Improve the Interruption Performance
- Thermal Analysis of AC Contactor Using Thermal Network Finite Difference Analysis Method(Session 7 -Modeling-)
- Research on the Electrical Performance of CuCrTa and CuCr55 Contact Materials for 126kV Vacuum Interrupter
- Hybridized Time-Domain Macromodeling and Circuit Simulation for Signal Integrity Analysis of the High-Speed Interconnects On PCB (国際セッションIS-EMD2005) -- (Signal Transmission and Optical Connectors)
- A new method to calculate the frequency characteristics of the Rogowski coil based on the frequency simulation(Session 6 : Sensing Devices)
- Theoretical Investigation on the Interference Rejection for the Current Measurement Using Magnetic Sensor Arrays(IS-EMD2003 : Recent Technical Trend of Electro-Mechanical Devices)
- Theoretical investigation on the interference rejection for the current measurement using magnetic sensor arrays (国際セッションIS--EMD 2003) -- (Session 2 Measurements and evaluation)
- Theoretical investigation on the interference rejection for the current measurement using magnetic sensor arrays
- Three Dimensional Numerical Simulation of Various Thermo-mechanical Processes by FEM (Report IV) : Deformation Analysis of Pipe-Plate Joint with Holes by Multi-pass Welding(Mechanics, Strength & Structural Design)
- Three Dimensional Numerical Simulation of Various Thermo-mechanical Processes by FEM (Report III) : Deformation Analysis of Compressors under Assembly by Plug Welding(Mechanics, Strength & Structural Design)
- Three Dimensional Numerical Simulation of Various Thermo-mechanical Processes by FEM (Report II) : Deformation Analysis of Compressor under Assembly by Shrinkage Fit(Mechanics, Strength & Structural Design)
- Three Dimensional Numerical Simulation of Various Thermo-mechanical Processes by FEM (Report I) : Methods for Improving the convergence of 3-D Analysis of Welding(Mechanics, Strength & Structural Design)
- Research on Capacitive Divider with Symmetrical Low-Voltage Arms
- Thermal Analysis of AC Contactor Using Thermal Network Finite Difference Analysis Method
- New Method to Model the Equivalent Circuit of the Pulse Generator in Electrical Fast Transient/Burst Test
- New Method to Model the Equivalent Circuit of the Pulse Generator in EFT/B Test
- Implementation of ASIC for Monitoring and Control Unit in Intelligent Electrical Apparatus (国際セッションIS-EMD2005) -- (Signal Transmission and Optical Connectors)
- Criteria for Heated Band Width Based on Through-thickness Temperature Distribution - Numerical Study on Local PWHT of Butt Welded Pipe (Report 1) -
- Simulation of Permanent Magnetic Actuators with Multi-magnetic Circuit for High Voltage Vacuum Circuit Breakers
- Mechanical Behavior in Local Post Weld Heat Treatment (Report IV) : Influence of residual stress distribution in multi-pass welding(Mechanics, Strength & Structure Design)
- Mechanical Behavior in Local Postweld Heat Treatment (Report III) : Criteria for heated band width based on through-thickness temperature distribution(Mechanics, Strength & Structure Design)
- Mechanical Behavior in Local Postweld Heat Treatment (Report II) : Determination of Critical Heated Band during Local PWHT(Mechanics, Strength & Structure Design)
- Mechanical Behavior in Local Post Weld Heat Treatment (Report I) : Visco-Elastic-Plastic FEM Analysis of Local PWHT(Mechanics, Strength & Structure Design)
- A Control Method for Improving Performance of Permanent Magnetic Actuators in Vacuum Circuit Breakers
- Simulation of Permanent Magnetic Actuators with Multi-magnetic Circuit for High Voltage Vacuum Circuit Breakers
- Modeling of the Combination Wave Generator and Simulation of the Surge Immunity Test
- Heated Band Width Criterion Based on Stress Relief in Local Post Weld Heat Treatment of Concurrent Tubular Joint(Mechanics, Strength & Structure Design)
- Modeling of the Electrical Fast Transient/Burst Generator and the Standard Injection Clamp