On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
スポンサーリンク
概要
- 論文の詳細を見る
In this report the authors investigate the influence of the construction and the dimension of toothed belt and some running conditions on the noise of toothed belt drive, and show some running noise reduction methods and their effectiveness. The running noise level varies with belt speed, belt tension and polygon-effect of the wheel, but there is no difinite tendency between noise level and number of teeth and module of the wheel. The effective methods to reduce the meshing impact sound and to keep the toothed belt drive silent are: (1) to soften the bottom lands of toothed belt or the tooth tip lands of wheel, (2) to make belt width narrow, (3) to cant the belt of tension side with an idle pulley, (4) to make the wheel noncylindrical, especially as barreled-shape.
- 一般社団法人日本機械学会の論文
著者
-
Ando Toshiaki
Faculty Of Engineering. Kyoto University.
-
Aida Toshio
Osaka Industrial University
-
SATO Susumu
Faculty of Engineering,Kyoto University
-
SATO Susumu
Kyoto University
-
HOSHIRO Takeshi
Mitsuboshi Belting Ltd.
-
KUBO Aizoh
Faculty of Engineering. Kyoto University.
-
AIDA Toshio
Faculty of Engineering, Kyoto University.
-
HOSHIRO Takeshi
Chief Research Fellow, Mitsuboshi Belting Co., Ltd.
-
Kubo Aizoh
Faculty Of Engineering Kyoto University
-
Aida Toshio
Faculty Of Engineering Kvoto University
-
Sato Susumu
Faculty Of Engineering Kyoto University
-
Kubo Aizoh
Faculty Of Engineering Kyoto Univ.
-
Hoshino Takeshi
Mitsuboshi Belt. Co. Ltd.
関連論文
- Study on the Mechanism of Train Noise and its Countermeasures : Part11, The Effect of Velocity and Load, and the Characteristics of Sound Radiation
- Study on the Mechanism of Noise Generation of Railway Wheel and its Countermeasure : 5th Report, Flexural Vibration and Noise of a Spoke Type Wheel
- A Study on Transmission Characteristics of Toothed Belt Drives : 5th Report, Relative Shifting between Belt and Pulley in Normal and Reverse Revolutions under a State of Initial Tension
- A Study on Transmission Characteristics of Toothed Belt Drives : 4th report, Transmission Error at Normal and Reverse Revolution under a State of Initial Tension
- Load Distribution on Toothed Belt Drives under a State of Initial Tension
- A Study on Transmission Characteristics of Toothed Belt Drives : 3rd report, Transmission Error under a State of Applied Initial Tension, Experimental Results
- A Study on Transmission Characteristics of Toothed Belt Drives : 2nd report, Transmission Error under a State of Applied Initial Tension, Theoretical Analysis
- A Study on Transmission Characteristics of Toothed Belt Drives : 1st report, Effect of Initial Tension on Tight side and Slack Side Tensions
- Some Methods to Reduce Noise in Toothed Belt Drives
- A Study on Strength of Toothed Belt : 6th report, Behavior of Belt and Pulley Tooth at Incomplete Meshing Region
- A Study on Strength of Toothed Belt : 5th Report, Effect of Pitch Difference on Fatigue Strength of Toothed Belt
- A Study on Strength of Toothed Belt : 4th Report, Load Distribution in Case of Considering Incomplete Meshing
- A Study on Strength of Toothed Belt : 3rd Report, Fatigue Strength and Features of Fracture
- On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
- On the Running Noise of Toothed Belt Drive : 1st Report, Mechanism of Noise Generation
- Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
- Development of a New Production System for High-precision, Low-cost Gears of Automobile Manual Transaxles under High-volume Production
- A Study on Strength of Toothed Belt : 7th report, Wear of Polyurethane Belt under No Load
- A Study on Strength of Toothed Belt : 2nd Report, Influence of Pitch Difference on Load Distribution
- Distortions and Residual Stresses of Gears Caused by Hardening : 5th Report, Gear with Limited Face Width
- Distortions and Residual Stresses of Gears Caused by Hardening : 1st Report, Through-Hardening of Solid Cylinder Made of S45C Carbon Steel
- Influence of Impact Load on Fatigue Bending Strength of Case-Hardened Gears
- On the Durability of Gears for Machine Tools (the Journal and the Transactions of the Japan Society of Mechanical Engineers)
- Research on Force-Fitted Gear : Part 10-Deformation in each part of gear rim caused by force-fitting
- Study on Bending Fatigue Strength of Gears : 8th Report, Calculating Formula of True Stress at Compressive Side Tooth Fillet and Stresses in Operation
- Research on the Force-Fitted Gear : 9th Report, The Influence of Projections around a Cylinder, Repeated Numbers of Fitting and Extracting Processes on Fitting and Extracting Forces and Conditions of Fitting Surface
- Research of Force-Fitted Gear : 5th Report, On the Distribution of Stress along the Fillet Curve of Gears having Bosses on their Sides and Large Size Gear
- Research of Force-Fitted Gear : 6th Report, On the Distribution of Stress along the Fillet Curve in Case when Gear Rim and Boss are made of Different Materials
- Research on the Force-Fitted Gear : 8th Report, On the Fillet Stress of the Gear Tooth in Case when Hubs of Various Shapes are force-fitted and a Solid Shaft is double force-fitted in the Hollow Hub
- Research of Force-Fitted Gear : 4th Report, On the Improvement of Bending Fatigue Strength by Surface Rolling at the Root Fillet of the Force-Fitted Gear Tooth
- Study on the Stress at the Root Fillet and Safety for Slipping of Force-fitted Helical Gears
- Reserarch on the Force-Fitted Gear : 7th Report, On the Change of Stresses at the Circumference of the Force-Fitted Part in the Slipping Test
- Bending Strength Design of Gears
- Tooth Fillet Stresses of Gear with Thin Rim : 3rd report, Examination of Approximation Formulae for Gear Tooth Fillet Stresses
- Tooth Fillet Stresses of Gear with Thin rim : 2nd report, Approximation Formulae for Tooth Fillet Stresses
- Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation
- Bending Stresses of Internal Spur Gear
- Research of Force-Fitted Gear : 2nd Report, On the Bending Fatigue Strength of Force-Fitted Gear
- Research of Force-Fitted Gear : 1st Report, On the Distribution of Stress along the Fillet Curve of a Spur Gear
- A Computer Based Approach for Evaluation of Operating Performances of Bevel and Hypoid Gears
- Bending Fatigue Strength of Gears
- On the Stresses of Force-Fitted Gear and the Slipping at Force-Fitted Surface when the Influence of Centrifugal Force is considered
- Distortions and Residual Stresses of Gears Caused by Hardening : 3rd Report, Induction-Hardening of Gears Made of S35C Carbon Steel
- Distortions and Residual Stresses of Gears Caused by Hardening : 2nd Report, Through-Hardening of Gear Made of S45C Carbon Steel
- Fundamental on Scoring Failure : 2nd report: A Model for Scoring and Critical Temperature
- Fundamental on Scoring Failure : 1st report, Initiation and Progress of Scoring on Gear Teeth
- Tooth Fillet Stresses of Gear with Thin Rim : 5th report, Tooth Fillet and Root Stresses of Internal Spur Gear Supported by Pinned Coupling
- Tooth Fillet Stresses of Gear with Thin Rim : 4th report, Approximation Formulae for Tooth Fillet and Root Stresses of Internal Spur Gear
- Fundamental on Scoring Failure : 3rd Report: Improvement of Scoring Model and Definition of Scoring Index
- A Method for Fast Estimation of the Vibration of Spur Gears : Series C : Vibration, Control Engineering, Engineering for Industry
- On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
- On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
- On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
- Bending Fatigue Strength of Case-Hardened Gears
- On the Creep and the Relaxation of Spiral Ropes
- Bending Fatigue Strength of Gears under Various Loading Conditions
- Deflections and Moments of Wide Plate with Varying Thickness in Direction of Height
- Fundamental Research on Gear Noise and Vibration : (6th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears)
- Research on Bending Strength Properties of Spur Gears with a Thin Rim
- Distortions and Residual Stresses of Gears Caused by Hardening : 4th Report, Case-Hardening of Gears
- Research of Force-Fitted Gear : 3rd Report, On the Bending Fatigue Strength of Shrinkage-Fitted Gears
- Fundamental Research on Gear Noise and Vibration : 7th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears-II