Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation

スポンサーリンク

概要

• 論文の詳細を見る

• This paper introduces an Automatic Mesh Generator (AMG) for finite element method (FEM) to analyze tooth fillet stresses of gears with a thin rim. The AMG incorporates 'Basic Mesh', i.e., a set of regular meshes : Nodes and elements for the FEM calculation are efficiently decided on the basic mesh. Coordinates of nodes of the model are calculated by an imaginary elastic deformation of the basic mesh. By the selection of a proper form of the mesh and by changing the imaginary elastic characteristics of the basic mesh, a proper distribution of nodes on the model for FEM-analysis is obtained. The amount of input data to AMG is determined only by the complexity of the model shape. The input data for another similar model can be easily made by a little correction of the input data. The values of the gear tooth fillet stresses calculated by FEM using this AMG showed satisfactory results.

• 一般社団法人日本機械学会の論文

著者

• KUBO Aizoh

  Faculty of Engineering. Kyoto University.

• AIDA Toshio

  Faculty of Engineering, Kyoto University.

• Kubo Aizoh

  Faculty Of Engineering Kyoto University

• Chong Tae-hyong

  Dept. Of Mechanical Engineering College Of Engineering Hanyang University

• Aida Toshio

  Faculty Of Engineering Kvoto University

• Fujio Hiroshige

  Faculty Of Engineering Kyoto University

• SUZUKI Toshiyuki

  Process Engineering Section, Kyoto Works, Mitsubish Motors Corporation

• CHONG Tae-Hyong

  Graduate School of Engineering, Kyoto University

• Suzuki Toshiyuki

  Process Engineering Section Kyoto Works Mitsubishi Motors Corporation

• Kubo Aizoh

  Faculty Of Engineering Kyoto Univ.

• FUJIO Hiroshige

  Faculty of Engineering, Kyoto University

• AIDA Toshio

  Faculty of Engineering, Osaka Industrial University

関連論文

• On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
• On the Running Noise of Toothed Belt Drive : 1st Report, Mechanism of Noise Generation
• Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
• Development of a New Production System for High-precision, Low-cost Gears of Automobile Manual Transaxles under High-volume Production
• Distortions and Residual Stresses of Gears Caused by Hardening : 5th Report, Gear with Limited Face Width
• Distortions and Residual Stresses of Gears Caused by Hardening : 1st Report, Through-Hardening of Solid Cylinder Made of S45C Carbon Steel
• Influence of Impact Load on Fatigue Bending Strength of Case-Hardened Gears
• On the Durability of Gears for Machine Tools (the Journal and the Transactions of the Japan Society of Mechanical Engineers)
• Research on Force-Fitted Gear : Part 10-Deformation in each part of gear rim caused by force-fitting
• Study on Bending Fatigue Strength of Gears : 8th Report, Calculating Formula of True Stress at Compressive Side Tooth Fillet and Stresses in Operation
• Research on the Force-Fitted Gear : 9th Report, The Influence of Projections around a Cylinder, Repeated Numbers of Fitting and Extracting Processes on Fitting and Extracting Forces and Conditions of Fitting Surface
• Research of Force-Fitted Gear : 5th Report, On the Distribution of Stress along the Fillet Curve of Gears having Bosses on their Sides and Large Size Gear
• Research of Force-Fitted Gear : 6th Report, On the Distribution of Stress along the Fillet Curve in Case when Gear Rim and Boss are made of Different Materials
• Research on the Force-Fitted Gear : 8th Report, On the Fillet Stress of the Gear Tooth in Case when Hubs of Various Shapes are force-fitted and a Solid Shaft is double force-fitted in the Hollow Hub
• Research of Force-Fitted Gear : 4th Report, On the Improvement of Bending Fatigue Strength by Surface Rolling at the Root Fillet of the Force-Fitted Gear Tooth
• Study on the Stress at the Root Fillet and Safety for Slipping of Force-fitted Helical Gears
• Reserarch on the Force-Fitted Gear : 7th Report, On the Change of Stresses at the Circumference of the Force-Fitted Part in the Slipping Test
• Bending Strength Design of Gears
• Tooth Fillet Stresses of Gear with Thin Rim : 3rd report, Examination of Approximation Formulae for Gear Tooth Fillet Stresses
• Tooth Fillet Stresses of Gear with Thin rim : 2nd report, Approximation Formulae for Tooth Fillet Stresses
• Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation
• Bending Stresses of Internal Spur Gear
• Research of Force-Fitted Gear : 2nd Report, On the Bending Fatigue Strength of Force-Fitted Gear
• Research of Force-Fitted Gear : 1st Report, On the Distribution of Stress along the Fillet Curve of a Spur Gear
• A Computer Based Approach for Evaluation of Operating Performances of Bevel and Hypoid Gears
• Bending Fatigue Strength of Gears
• On the Stresses of Force-Fitted Gear and the Slipping at Force-Fitted Surface when the Influence of Centrifugal Force is considered
• GSD-17 A STUDY ON THE HEAT-TREATMENT TECHNIQUE FOR DEFORMATION CONTROL OF LANDING GEARS(GEAR STRENGTH AND DURABILITY)
• Distortions and Residual Stresses of Gears Caused by Hardening : 3rd Report, Induction-Hardening of Gears Made of S35C Carbon Steel
• Distortions and Residual Stresses of Gears Caused by Hardening : 2nd Report, Through-Hardening of Gear Made of S45C Carbon Steel
• Residual Stress of Case-Hafdened Splined Shaft with Straight-Sided Teeth
• Fundamental on Scoring Failure : 2nd report: A Model for Scoring and Critical Temperature
• Fundamental on Scoring Failure : 1st report, Initiation and Progress of Scoring on Gear Teeth
• Tooth Fillet Stresses of Gear with Thin Rim : 5th report, Tooth Fillet and Root Stresses of Internal Spur Gear Supported by Pinned Coupling
• Tooth Fillet Stresses of Gear with Thin Rim : 4th report, Approximation Formulae for Tooth Fillet and Root Stresses of Internal Spur Gear
• Fundamental on Scoring Failure : 3rd Report: Improvement of Scoring Model and Definition of Scoring Index
• A Method for Fast Estimation of the Vibration of Spur Gears : Series C : Vibration, Control Engineering, Engineering for Industry
• On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
• On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
• On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
• Bending Fatigue Strength of Case-Hardened Gears
• On the Creep and the Relaxation of Spiral Ropes
• Bending Fatigue Strength of Gears under Various Loading Conditions
• Influence of Hardenability on Helical Gear Distortions Caused by Hardening : 1st Report, Through-Hardening of Gears Made of Low Alloyed Steels
• Deflections and Moments of Wide Plate with Varying Thickness in Direction of Height
• Fundamental Research on Gear Noise and Vibration : (6th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears)
• Research on Bending Strength Properties of Spur Gears with a Thin Rim
• Distortions and Residual Stresses of Gears Caused by Hardening : 4th Report, Case-Hardening of Gears
• Research of Force-Fitted Gear : 3rd Report, On the Bending Fatigue Strength of Shrinkage-Fitted Gears
• Fundamental Research on Gear Noise and Vibration : 7th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears-II

もっと見る 閉じる

スポンサーリンク