Distortions and Residual Stresses of Gears Caused by Hardening : 1st Report, Through-Hardening of Solid Cylinder Made of S45C Carbon Steel

スポンサーリンク

概要

• 論文の詳細を見る

• Distortions of gear tooth caused by hardening decrease gear accuracies, and residual stresses due to hradening influence considerably the bending fatigue strength of gear tooth. But few papers are concerned with distortions and residual stresses of gears. In this report as the first step to studying the distortions and the residual stresses of gears caused by hardening, those of a cylinder caused by water quenching are studied theoretically and experimentally. Coefficient of thermal expansion during martensite transformation and heat transfer coefficient of water during cooling for the cylinders with various diameters, were obtained experimentally. The yield stresses of a cylinder during the martensite transformation were assumed from some of authors' measurements. The residual stresses were calculated applying these data by the elastic-plastic finite element method, and they were also measured experimentally by Sachs' method. Results of the numerical calculations and experiments showed good coincidence qualitatively and quantitatively. Consequently, availability of calculation was confirmed.

著者

• Aida Toshio

  Faculty Of Engineering Osaka Industrial University

• Aida Toshio

  Faculty Of Engineering Kvoto University

• Fujio Hiroshige

  Faculty Of Engineering Kyoto University

• Masumoto Yuji

  Ishikawajima-harima Heavy Industries Co. Ltd.

関連論文

• On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
• On the Running Noise of Toothed Belt Drive : 1st Report, Mechanism of Noise Generation
• Distortions and Residual Stresses of Gears Caused by Hardening : 5th Report, Gear with Limited Face Width
• Distortions and Residual Stresses of Gears Caused by Hardening : 1st Report, Through-Hardening of Solid Cylinder Made of S45C Carbon Steel
• Influence of Impact Load on Fatigue Bending Strength of Case-Hardened Gears
• On the Durability of Gears for Machine Tools (the Journal and the Transactions of the Japan Society of Mechanical Engineers)
• Research on Force-Fitted Gear : Part 10-Deformation in each part of gear rim caused by force-fitting
• Study on Bending Fatigue Strength of Gears : 8th Report, Calculating Formula of True Stress at Compressive Side Tooth Fillet and Stresses in Operation
• Research on the Force-Fitted Gear : 9th Report, The Influence of Projections around a Cylinder, Repeated Numbers of Fitting and Extracting Processes on Fitting and Extracting Forces and Conditions of Fitting Surface
• Research of Force-Fitted Gear : 5th Report, On the Distribution of Stress along the Fillet Curve of Gears having Bosses on their Sides and Large Size Gear
• Research of Force-Fitted Gear : 6th Report, On the Distribution of Stress along the Fillet Curve in Case when Gear Rim and Boss are made of Different Materials
• Research on the Force-Fitted Gear : 8th Report, On the Fillet Stress of the Gear Tooth in Case when Hubs of Various Shapes are force-fitted and a Solid Shaft is double force-fitted in the Hollow Hub
• Research of Force-Fitted Gear : 4th Report, On the Improvement of Bending Fatigue Strength by Surface Rolling at the Root Fillet of the Force-Fitted Gear Tooth
• Study on the Stress at the Root Fillet and Safety for Slipping of Force-fitted Helical Gears
• Reserarch on the Force-Fitted Gear : 7th Report, On the Change of Stresses at the Circumference of the Force-Fitted Part in the Slipping Test
• Bending Strength Design of Gears
• Tooth Fillet Stresses of Gear with Thin Rim : 3rd report, Examination of Approximation Formulae for Gear Tooth Fillet Stresses
• Tooth Fillet Stresses of Gear with Thin rim : 2nd report, Approximation Formulae for Tooth Fillet Stresses
• Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation
• Bending Stresses of Internal Spur Gear
• Research of Force-Fitted Gear : 2nd Report, On the Bending Fatigue Strength of Force-Fitted Gear
• Research of Force-Fitted Gear : 1st Report, On the Distribution of Stress along the Fillet Curve of a Spur Gear
• Bending Fatigue Strength of Gears
• On the Stresses of Force-Fitted Gear and the Slipping at Force-Fitted Surface when the Influence of Centrifugal Force is considered
• Distortions and Residual Stresses of Gears Caused by Hardening : 3rd Report, Induction-Hardening of Gears Made of S35C Carbon Steel
• Distortions and Residual Stresses of Gears Caused by Hardening : 2nd Report, Through-Hardening of Gear Made of S45C Carbon Steel
• Residual Stress of Case-Hafdened Splined Shaft with Straight-Sided Teeth
• On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
• On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
• On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
• Bending Fatigue Strength of Case-Hardened Gears
• On the Creep and the Relaxation of Spiral Ropes
• Bending Fatigue Strength of Gears under Various Loading Conditions
• Influence of Hardenability on Helical Gear Distortions Caused by Hardening : 1st Report, Through-Hardening of Gears Made of Low Alloyed Steels
• Deflections and Moments of Wide Plate with Varying Thickness in Direction of Height
• Fundamental Research on Gear Noise and Vibration : (6th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears)
• Research on Bending Strength Properties of Spur Gears with a Thin Rim
• Distortions and Residual Stresses of Gears Caused by Hardening : 4th Report, Case-Hardening of Gears
• Research of Force-Fitted Gear : 3rd Report, On the Bending Fatigue Strength of Shrinkage-Fitted Gears
• Fundamental Research on Gear Noise and Vibration : 7th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears-II

もっと見る 閉じる

スポンサーリンク