On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
スポンサーリンク
概要
- 論文の詳細を見る
For the purpose of calculating the bending strength of the gear tooth in general use, the authors studied theoretically the position of the weakest section of a gear tooth and the point of the worst loading, and consequently defined the calculating method of nominal stress. Then by using the calculating equation of bending stress and stress concentration factor of gear teeth of various shapes in general use at present, they studied these relations.
- 一般社団法人日本機械学会の論文
著者
-
Aida Toshio
Faculty Of Engineering Kvoto University
-
Terauchi Yoshio
Faculty Of Engiineering Hiroshima University
関連論文
- A Study on the Dynamic Behavior of a Skew Bevel Gear : 1st Report, On Root Stress Ratio, Torsional Vibration, Bending Vibration of Gear Shaft, and Vibrating Displacements in Three Right-Angled Directions : Series C : Vibration, Control Engineering, Engine
- Study on Tooth Bearing of Bevel Gears : 2nd Report, Relation between Tooth Bearing and Assembly Error, Shaft Angle Error
- Study on Tooth Bearing of Bevel Gears : 1st Report, Theoretical Calculation of Tooth Bearing and Experiment
- On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
- On the Running Noise of Toothed Belt Drive : 1st Report, Mechanism of Noise Generation
- Distortions and Residual Stresses of Gears Caused by Hardening : 5th Report, Gear with Limited Face Width
- Distortions and Residual Stresses of Gears Caused by Hardening : 1st Report, Through-Hardening of Solid Cylinder Made of S45C Carbon Steel
- Influence of Impact Load on Fatigue Bending Strength of Case-Hardened Gears
- On the Durability of Gears for Machine Tools (the Journal and the Transactions of the Japan Society of Mechanical Engineers)
- Research on Force-Fitted Gear : Part 10-Deformation in each part of gear rim caused by force-fitting
- Study on Bending Fatigue Strength of Gears : 8th Report, Calculating Formula of True Stress at Compressive Side Tooth Fillet and Stresses in Operation
- Research on the Force-Fitted Gear : 9th Report, The Influence of Projections around a Cylinder, Repeated Numbers of Fitting and Extracting Processes on Fitting and Extracting Forces and Conditions of Fitting Surface
- Research of Force-Fitted Gear : 5th Report, On the Distribution of Stress along the Fillet Curve of Gears having Bosses on their Sides and Large Size Gear
- Research of Force-Fitted Gear : 6th Report, On the Distribution of Stress along the Fillet Curve in Case when Gear Rim and Boss are made of Different Materials
- Research on the Force-Fitted Gear : 8th Report, On the Fillet Stress of the Gear Tooth in Case when Hubs of Various Shapes are force-fitted and a Solid Shaft is double force-fitted in the Hollow Hub
- Research of Force-Fitted Gear : 4th Report, On the Improvement of Bending Fatigue Strength by Surface Rolling at the Root Fillet of the Force-Fitted Gear Tooth
- Study on the Stress at the Root Fillet and Safety for Slipping of Force-fitted Helical Gears
- Reserarch on the Force-Fitted Gear : 7th Report, On the Change of Stresses at the Circumference of the Force-Fitted Part in the Slipping Test
- Bending Strength Design of Gears
- Tooth Fillet Stresses of Gear with Thin rim : 2nd report, Approximation Formulae for Tooth Fillet Stresses
- Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation
- Bending Stresses of Internal Spur Gear
- Research of Force-Fitted Gear : 2nd Report, On the Bending Fatigue Strength of Force-Fitted Gear
- Research of Force-Fitted Gear : 1st Report, On the Distribution of Stress along the Fillet Curve of a Spur Gear
- Bending Fatigue Strength of Gears
- On the Stresses of Force-Fitted Gear and the Slipping at Force-Fitted Surface when the Influence of Centrifugal Force is considered
- Study on Friction Loss of Internal Gear Drives : Intluence of Pinion Surface Finishing, Gear Speed and Torque
- On the Heat Balance of Gear Equipment : On a Method for Predicting the Bulk Temperature Rise of Gears and Temperature Rise of Oil with Dip Cooling
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Prediction of Crack Propagation and Fatigue Life of MAC14 Supercarburized Steel Gear
- Distortions and Residual Stresses of Gears Caused by Hardening : 3rd Report, Induction-Hardening of Gears Made of S35C Carbon Steel
- Distortions and Residual Stresses of Gears Caused by Hardening : 2nd Report, Through-Hardening of Gear Made of S45C Carbon Steel
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Reliability Estimation of Bending Fatigue Strength of Supercarburized Steel Gear
- On Heat- Balance of Gear-Meshing Apparatus : Experimental and Analytical Heat Transfer Coefficient on Tooth Faces
- Scoring Resistance of Spur Gears with Various Coatings : 1st Report, Scoring Tests under Forced Lubrication
- Correlation of Cavitation Damage Tests with Residual Stress Measurements
- On the Relation between the Run-Out Errors and the Motion of the Center of Sun Gear In a Stoeckicht Planetary Gear
- On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
- Dynamic Behavior of Straight Bevel Gear : 1st Report, Dynamic Load Torque Variation and Bending Vibration of Gear Shaft
- Study on Deflection of Spur Gear Teeth : 2nd Report, Calculation of Tooth Deflection for Spur Gears with Various Tooth Profiles
- Study on Deflection of Spur Gear Teeth : last Report, Calculation of Tooth Deflection by Two-dimensional Elastic Theory
- Influence of EP Film Properties on Anti-scoring Performance of Gears
- ON THE EFFECT OF THE TOOTH PROFILE MODIFICATION ON THE DYNAMIC LOAD AND THE SOUND LEVEL OF THE SPUR GEAR
- ON THE SURFACE TEMPERATURE RISE AT THE FOUR-BALL TESTS
- On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
- Basic Studies on Scoring of Spur Gears : 4th Report, Effect of Module on Scoring Resistance
- On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
- STUDIES ON SCORING OF SPUR GEARS : 3RD REPORT, EFFECT OF THE COEFFICIENT OF ADDENDUM MODIFICATION ON SCORING RESISTANCE
- Dynamic Behavior of Planetary Gear : 1st Report Load Distribution in Planetary Gear
- Studies on the Scoring by Using a Crossed Cylinders Friction Machine : 1st Report, On the Initial Situation of Scoring
- BASIC STUDIES ON SCORING OF SPUR GEARS : 2ND REPORT, EXPERIMENTAL RESULTS USING POWER CIRCULATING GEAR TEST RIG
- Dynamic Behavior of Straight Bevel Gear : 2nd Report, Vibration of Bevel Gears on Rectangular-coordinate
- Analysis of Dynamic Tooth Load on Planetary Gear
- Bending Fatigue Strength of Case-Hardened Gears
- On the Creep and the Relaxation of Spiral Ropes
- Bending Fatigue Strength of Gears under Various Loading Conditions
- Study on Rippling Failure by the Roller Test : 1st Report, On the Progress and Limit of Rippling Failure
- Effect of Lubricating Oil on Rippling Failure
- Dynamic Behavior of Planetary Gear : 7th Report, Influence of the Thickness of the Ring Gear
- Dynamic Behavior of Planetary Gear : 6th Report, Influence of Meshing-Phase
- Dynamic Behavior of Planetary Gear : 5th report, Dynamic Increment of Torque
- On Surface Durability of Involute-cycloid Composite Tooth Profile Gear
- On Design Performance of Involute-cycloid Composite Tooth Profile Gear
- Study on Load-carrying Capacities of Tip-chamfered Gears
- STUDY ON LOAD-CARRYING CAPACITIES OF CARBURIZED GEARS OF BEADED FREE-CUTTING STEEL
- The Mechanism of Seizure in Two-Roller Tests : Vibration, Control Engineering, Engineering for Industry
- Seizure Resistance of Coatings in Four Ball Tests, Two Roller Tests and Gear Tests : Vibration, Control Engineering, Engineering for Industry
- Scoring Resistance of Spur Gears with Various Coatings : 2nd Report, Scoring Tests under Dry Friction
- On the Temperature Rise Caused by Moving Heat Sources : 2nd Report, Calculation of Temperature Considering Heat Radiation from Surface
- Scoring Resistance of Copper-plated Gears
- On the Temperature Rise Caused by Moving Heat Sources : 1st Report, Calculation of the Temperature under Three-dimensional Heat Flow
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 1st Report, The Case of Meshing with a Pair of Ground Standard Gears
- On the Flash Temperature Rise of the Tooth Surface of Surface-Hardened Gear : 1 st Report, Effect of Thermal Conductivity in the Surface Layers of Surface-Hardened Gears
- Basic Studies on Scoring of Spur Gears : 1st Report, On the Seizure under a Pure Sliding Condition and a Sliding-Rolling Condition
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 2nd Report, The Effects of the Amount of Addendum Modification and the Accuracy of Gears on the Tooth Surface Temperature
- Dynamic Behavior of Straight Bevel Gear : 3rd Report, On the Effect of Preloading on Bearing
- Deflections and Moments of Wide Plate with Varying Thickness in Direction of Height
- A Study on Rolling Finish of Gear : Theoretical Analysis of Number of Contact Points and Plastic Deformations
- A Study on Rolling Finish of Gear : End Effects
- Dynamic Behavior of Planetary Gear : 4th Report, Influence of the Transmitted Tooth Load on the Dynamic Increment Load
- Dynamic Behavior of Planetary Gear : 2nd Report, Displacement of Sun Gear and Ring Gear
- Dynamic Behavior of Planetary Gear : 3rd Report, Displacement of Ring Gear in Direction of Line of Action
- Fundamental Research on Gear Noise and Vibration : (6th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears)
- Research on Bending Strength Properties of Spur Gears with a Thin Rim
- Distortions and Residual Stresses of Gears Caused by Hardening : 4th Report, Case-Hardening of Gears
- Research of Force-Fitted Gear : 3rd Report, On the Bending Fatigue Strength of Shrinkage-Fitted Gears
- Fundamental Research on Gear Noise and Vibration : 7th Report, Generation Mechanism of Radial and Axial Vibration of Spur Gears-II
- A Study on Rolling Finish of Gear : Plastic Deformations by Rolling Experiment of Rollers