On the Temperature Rise Caused by Moving Heat Sources : 2nd Report, Calculation of Temperature Considering Heat Radiation from Surface
スポンサーリンク
概要
- 論文の詳細を見る
The temperature rise caused by the moving heat sources of which the distributions of heat intensities are parabolic and uniform over the area of a rectangle was calculated in consideration of heat radiation from the surface under the assumption of a three-dimensional heat flow. Further, the flash temperature rise generated on the meshing faces of the gears was examined by estimating convective heat transfer coefficient between the tooth surface and a lubricating oil. From the calculated results it is seen that the difference between the maximum values of the temperature rise caused by the above-cited distributed heat sources decreases with an increasing heat transfer coefficient, and the effect of heat radiation on the flash temperature rise of the tooth surface is considered negligible.
- 一般社団法人日本機械学会の論文
著者
-
Kohno Masaki
Kure National College Of Technology
-
NADANO Hiromasa
Kure College of Technology
-
Terauchi Y
Faculty Of Engineering Fukuyama University
-
Nadano Hiromasa
Department of Mechanical Engineering ,Kure National College of Technology
-
Terauchi Yoshio
Faculty Of Engiineering Hiroshima University
-
Nadano H
Department Of Mechanical Engineering Kure National College Of Technology
-
Nadano Hiromasa
Kure National College Of Technology
関連論文
- A Study on the Dynamic Behavior of a Skew Bevel Gear : 1st Report, On Root Stress Ratio, Torsional Vibration, Bending Vibration of Gear Shaft, and Vibrating Displacements in Three Right-Angled Directions : Series C : Vibration, Control Engineering, Engine
- Study on Tooth Bearing of Bevel Gears : 2nd Report, Relation between Tooth Bearing and Assembly Error, Shaft Angle Error
- Study on Tooth Bearing of Bevel Gears : 1st Report, Theoretical Calculation of Tooth Bearing and Experiment
- Tribological Properties of Mechanical Seal in Thrust-Washer Test : Case of Refrigerating Machine Oil with Oiliness and Anti-Wear Additives
- Study on Friction Loss of Internal Gear Drives : Intluence of Pinion Surface Finishing, Gear Speed and Torque
- On the Heat Balance of Gear Equipment : On a Method for Predicting the Bulk Temperature Rise of Gears and Temperature Rise of Oil with Dip Cooling
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Prediction of Crack Propagation and Fatigue Life of MAC14 Supercarburized Steel Gear
- Effect of TiN-coated Film on Seizure in Four Ball Test
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Reliability Estimation of Bending Fatigue Strength of Supercarburized Steel Gear
- On Heat- Balance of Gear-Meshing Apparatus : Experimental and Analytical Heat Transfer Coefficient on Tooth Faces
- GSD-20 SCORING RESISTANCE OF AUSTENITIC STAINLESS STEEL GEARS WITH PLASMA DIFFUSION PROCESSING(GEAR STRENGTH AND DURABILITY)
- Scoring Resistance of Spur Gears with Various Coatings : 1st Report, Scoring Tests under Forced Lubrication
- Correlation of Cavitation Damage Tests with Residual Stress Measurements
- On the Relation between the Run-Out Errors and the Motion of the Center of Sun Gear In a Stoeckicht Planetary Gear
- On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
- Dynamic Behavior of Straight Bevel Gear : 1st Report, Dynamic Load Torque Variation and Bending Vibration of Gear Shaft
- Study on Deflection of Spur Gear Teeth : 2nd Report, Calculation of Tooth Deflection for Spur Gears with Various Tooth Profiles
- Study on Deflection of Spur Gear Teeth : last Report, Calculation of Tooth Deflection by Two-dimensional Elastic Theory
- Influence of EP Film Properties on Anti-scoring Performance of Gears
- ON THE EFFECT OF THE TOOTH PROFILE MODIFICATION ON THE DYNAMIC LOAD AND THE SOUND LEVEL OF THE SPUR GEAR
- ON THE SURFACE TEMPERATURE RISE AT THE FOUR-BALL TESTS
- On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
- Basic Studies on Scoring of Spur Gears : 4th Report, Effect of Module on Scoring Resistance
- On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
- STUDIES ON SCORING OF SPUR GEARS : 3RD REPORT, EFFECT OF THE COEFFICIENT OF ADDENDUM MODIFICATION ON SCORING RESISTANCE
- Dynamic Behavior of Planetary Gear : 1st Report Load Distribution in Planetary Gear
- Studies on the Scoring by Using a Crossed Cylinders Friction Machine : 1st Report, On the Initial Situation of Scoring
- BASIC STUDIES ON SCORING OF SPUR GEARS : 2ND REPORT, EXPERIMENTAL RESULTS USING POWER CIRCULATING GEAR TEST RIG
- Dynamic Behavior of Straight Bevel Gear : 2nd Report, Vibration of Bevel Gears on Rectangular-coordinate
- Analysis of Dynamic Tooth Load on Planetary Gear
- Study on Rippling Failure by the Roller Test : 1st Report, On the Progress and Limit of Rippling Failure
- Effect of Lubricating Oil on Rippling Failure
- Dynamic Behavior of Planetary Gear : 7th Report, Influence of the Thickness of the Ring Gear
- Dynamic Behavior of Planetary Gear : 6th Report, Influence of Meshing-Phase
- Dynamic Behavior of Planetary Gear : 5th report, Dynamic Increment of Torque
- On Surface Durability of Involute-cycloid Composite Tooth Profile Gear
- On Design Performance of Involute-cycloid Composite Tooth Profile Gear
- Study on Load-carrying Capacities of Tip-chamfered Gears
- STUDY ON LOAD-CARRYING CAPACITIES OF CARBURIZED GEARS OF BEADED FREE-CUTTING STEEL
- The Mechanism of Seizure in Two-Roller Tests : Vibration, Control Engineering, Engineering for Industry
- Seizure Resistance of Coatings in Four Ball Tests, Two Roller Tests and Gear Tests : Vibration, Control Engineering, Engineering for Industry
- Scoring Resistance of Spur Gears with Various Coatings : 2nd Report, Scoring Tests under Dry Friction
- On the Temperature Rise Caused by Moving Heat Sources : 2nd Report, Calculation of Temperature Considering Heat Radiation from Surface
- Scoring Resistance of Copper-plated Gears
- On the Temperature Rise Caused by Moving Heat Sources : 1st Report, Calculation of the Temperature under Three-dimensional Heat Flow
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 1st Report, The Case of Meshing with a Pair of Ground Standard Gears
- On the Flash Temperature Rise of the Tooth Surface of Surface-Hardened Gear : 1 st Report, Effect of Thermal Conductivity in the Surface Layers of Surface-Hardened Gears
- Basic Studies on Scoring of Spur Gears : 1st Report, On the Seizure under a Pure Sliding Condition and a Sliding-Rolling Condition
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 2nd Report, The Effects of the Amount of Addendum Modification and the Accuracy of Gears on the Tooth Surface Temperature
- Dynamic Behavior of Straight Bevel Gear : 3rd Report, On the Effect of Preloading on Bearing
- A Study on Rolling Finish of Gear : Theoretical Analysis of Number of Contact Points and Plastic Deformations
- A Study on Rolling Finish of Gear : End Effects
- Dynamic Behavior of Planetary Gear : 4th Report, Influence of the Transmitted Tooth Load on the Dynamic Increment Load
- Dynamic Behavior of Planetary Gear : 2nd Report, Displacement of Sun Gear and Ring Gear
- Dynamic Behavior of Planetary Gear : 3rd Report, Displacement of Ring Gear in Direction of Line of Action
- A Study on Rolling Finish of Gear : Plastic Deformations by Rolling Experiment of Rollers
- The Effect of the Hardness of Tooth Material on the Scoring Resistance of Gears : Vibration, Control Engineering, and Engineering for Industry, New materials, new energy, biotechnology, electronics, etc.