On Design Performance of Involute-cycloid Composite Tooth Profile Gear
スポンサーリンク
概要
- 論文の詳細を見る
Involute gears have been widely used because of their many advantageous properties. However, involute gears have a drawback that their tooth contact strength is weak, because the convex tooth surfaces contact each other in meshing. In the present study, the authors designed an involute-cycloid composite tooth profile gear having higher bending and contact strengths than those of an involute gear, and confirmed experimentally the superiority of this gear.
- 一般社団法人日本機械学会の論文
著者
-
NAGAMURA Kazuteru
Faculty of Engineering, Hiroshima University
-
Nagamura Kazuteru
Faculty Of Engineering Hiroshima University
-
Terauchi Yoshio
Faculty Of Engiineering Hiroshima University
-
SAIJO Hiromitsu
Minolta Camera Co., Ltd., Toyokawa BM Factory
-
Saijo Hiromitsu
Minolta Camera Co. Ltd. Toyokawa Bm Factory
関連論文
- A Study on the Dynamic Behavior of a Skew Bevel Gear : 1st Report, On Root Stress Ratio, Torsional Vibration, Bending Vibration of Gear Shaft, and Vibrating Displacements in Three Right-Angled Directions : Series C : Vibration, Control Engineering, Engine
- Study on Tooth Bearing of Bevel Gears : 2nd Report, Relation between Tooth Bearing and Assembly Error, Shaft Angle Error
- Study on Tooth Bearing of Bevel Gears : 1st Report, Theoretical Calculation of Tooth Bearing and Experiment
- Study on Friction Loss of Internal Gear Drives : Intluence of Pinion Surface Finishing, Gear Speed and Torque
- On the Heat Balance of Gear Equipment : On a Method for Predicting the Bulk Temperature Rise of Gears and Temperature Rise of Oil with Dip Cooling
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Prediction of Crack Propagation and Fatigue Life of MAC14 Supercarburized Steel Gear
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Reliability Estimation of Bending Fatigue Strength of Supercarburized Steel Gear
- On Heat- Balance of Gear-Meshing Apparatus : Experimental and Analytical Heat Transfer Coefficient on Tooth Faces
- Scoring Resistance of Spur Gears with Various Coatings : 1st Report, Scoring Tests under Forced Lubrication
- Correlation of Cavitation Damage Tests with Residual Stress Measurements
- On the Relation between the Run-Out Errors and the Motion of the Center of Sun Gear In a Stoeckicht Planetary Gear
- On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
- Dynamic Behavior of Straight Bevel Gear : 1st Report, Dynamic Load Torque Variation and Bending Vibration of Gear Shaft
- Study on Deflection of Spur Gear Teeth : 2nd Report, Calculation of Tooth Deflection for Spur Gears with Various Tooth Profiles
- Study on Deflection of Spur Gear Teeth : last Report, Calculation of Tooth Deflection by Two-dimensional Elastic Theory
- Influence of EP Film Properties on Anti-scoring Performance of Gears
- ON THE EFFECT OF THE TOOTH PROFILE MODIFICATION ON THE DYNAMIC LOAD AND THE SOUND LEVEL OF THE SPUR GEAR
- ON THE SURFACE TEMPERATURE RISE AT THE FOUR-BALL TESTS
- On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
- Basic Studies on Scoring of Spur Gears : 4th Report, Effect of Module on Scoring Resistance
- On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
- STUDIES ON SCORING OF SPUR GEARS : 3RD REPORT, EFFECT OF THE COEFFICIENT OF ADDENDUM MODIFICATION ON SCORING RESISTANCE
- Dynamic Behavior of Planetary Gear : 1st Report Load Distribution in Planetary Gear
- Studies on the Scoring by Using a Crossed Cylinders Friction Machine : 1st Report, On the Initial Situation of Scoring
- BASIC STUDIES ON SCORING OF SPUR GEARS : 2ND REPORT, EXPERIMENTAL RESULTS USING POWER CIRCULATING GEAR TEST RIG
- Dynamic Behavior of Straight Bevel Gear : 2nd Report, Vibration of Bevel Gears on Rectangular-coordinate
- Analysis of Dynamic Tooth Load on Planetary Gear
- Study on Rippling Failure by the Roller Test : 1st Report, On the Progress and Limit of Rippling Failure
- Effect of Lubricating Oil on Rippling Failure
- Dynamic Behavior of Planetary Gear : 7th Report, Influence of the Thickness of the Ring Gear
- Dynamic Behavior of Planetary Gear : 6th Report, Influence of Meshing-Phase
- Dynamic Behavior of Planetary Gear : 5th report, Dynamic Increment of Torque
- On Surface Durability of Involute-cycloid Composite Tooth Profile Gear
- On Design Performance of Involute-cycloid Composite Tooth Profile Gear
- Stress Analysis of Thin Rim Spur Gears by Finite Element Method
- Study on Load-carrying Capacities of Tip-chamfered Gears
- STUDY ON LOAD-CARRYING CAPACITIES OF CARBURIZED GEARS OF BEADED FREE-CUTTING STEEL
- The Mechanism of Seizure in Two-Roller Tests : Vibration, Control Engineering, Engineering for Industry
- Seizure Resistance of Coatings in Four Ball Tests, Two Roller Tests and Gear Tests : Vibration, Control Engineering, Engineering for Industry
- Scoring Resistance of Spur Gears with Various Coatings : 2nd Report, Scoring Tests under Dry Friction
- On the Temperature Rise Caused by Moving Heat Sources : 2nd Report, Calculation of Temperature Considering Heat Radiation from Surface
- Scoring Resistance of Copper-plated Gears
- On the Temperature Rise Caused by Moving Heat Sources : 1st Report, Calculation of the Temperature under Three-dimensional Heat Flow
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 1st Report, The Case of Meshing with a Pair of Ground Standard Gears
- On the Flash Temperature Rise of the Tooth Surface of Surface-Hardened Gear : 1 st Report, Effect of Thermal Conductivity in the Surface Layers of Surface-Hardened Gears
- Basic Studies on Scoring of Spur Gears : 1st Report, On the Seizure under a Pure Sliding Condition and a Sliding-Rolling Condition
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 2nd Report, The Effects of the Amount of Addendum Modification and the Accuracy of Gears on the Tooth Surface Temperature
- Dynamic Behavior of Straight Bevel Gear : 3rd Report, On the Effect of Preloading on Bearing
- A Study on Rolling Finish of Gear : Theoretical Analysis of Number of Contact Points and Plastic Deformations
- A Study on Rolling Finish of Gear : End Effects
- Dynamic Behavior of Planetary Gear : 4th Report, Influence of the Transmitted Tooth Load on the Dynamic Increment Load
- Dynamic Behavior of Planetary Gear : 2nd Report, Displacement of Sun Gear and Ring Gear
- Dynamic Behavior of Planetary Gear : 3rd Report, Displacement of Ring Gear in Direction of Line of Action
- A Study on Rolling Finish of Gear : Plastic Deformations by Rolling Experiment of Rollers