Dynamic Behavior of Straight Bevel Gear : 2nd Report, Vibration of Bevel Gears on Rectangular-coordinate
スポンサーリンク
概要
- 論文の詳細を見る
Using an inductance type vibrometer for shaft, the displacement of bevel gears is measured on a rectangular-coordinate, and the results are discussed. The results are as follows : The displacements of three directions perpendicularly intersecting each other are influenced by the bending stiffness of gear shaft and the stiffness of bearings. The displacements of three directions are influenced by the natural frequencies for torsional vibration of a gearing system and the natural frequency for bending vibration of a gear shaft. The vibration of high frequencies of 2fz, 3fz, 4fz etc. appears in the axial displacement of bevel gears. The vibration of low frequency is considerable influenced by the stiffness of bearing materials.
- 一般社団法人日本機械学会の論文
著者
-
Terauchi Yoshio
Faculty Of Engiineering Hiroshima University
-
FUJII Makoto
Faculty of Engineering, Hiroshima University
-
HOTO Hisao
Komatsu Works, Co. Ltd.
-
Fujii Makoto
Faculty Of Engineering Kinki University
-
Fujii Makoto
Faculty Of Engineering Hiroshima University
-
Hoto Hisao
Komatsu Works Co. Ltd.
関連論文
- A Study on the Dynamic Behavior of a Skew Bevel Gear : 1st Report, On Root Stress Ratio, Torsional Vibration, Bending Vibration of Gear Shaft, and Vibrating Displacements in Three Right-Angled Directions : Series C : Vibration, Control Engineering, Engine
- Study on Tooth Bearing of Bevel Gears : 2nd Report, Relation between Tooth Bearing and Assembly Error, Shaft Angle Error
- Study on Tooth Bearing of Bevel Gears : 1st Report, Theoretical Calculation of Tooth Bearing and Experiment
- Study on Friction Loss of Internal Gear Drives : Intluence of Pinion Surface Finishing, Gear Speed and Torque
- On the Heat Balance of Gear Equipment : On a Method for Predicting the Bulk Temperature Rise of Gears and Temperature Rise of Oil with Dip Cooling
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Prediction of Crack Propagation and Fatigue Life of MAC14 Supercarburized Steel Gear
- Study on Gear Bending Fatigue Strength Design Based on Reliability Engineering : Reliability Estimation of Bending Fatigue Strength of Supercarburized Steel Gear
- On Heat- Balance of Gear-Meshing Apparatus : Experimental and Analytical Heat Transfer Coefficient on Tooth Faces
- Scoring Resistance of Spur Gears with Various Coatings : 1st Report, Scoring Tests under Forced Lubrication
- Correlation of Cavitation Damage Tests with Residual Stress Measurements
- On the Relation between the Run-Out Errors and the Motion of the Center of Sun Gear In a Stoeckicht Planetary Gear
- On the Bending Stress of a Spur Gear : 3rd Report, On the Calculation Results of Bending Stress of a Gear Tooth
- Dynamic Behavior of Straight Bevel Gear : 1st Report, Dynamic Load Torque Variation and Bending Vibration of Gear Shaft
- Study on Deflection of Spur Gear Teeth : 2nd Report, Calculation of Tooth Deflection for Spur Gears with Various Tooth Profiles
- Study on Deflection of Spur Gear Teeth : last Report, Calculation of Tooth Deflection by Two-dimensional Elastic Theory
- Influence of EP Film Properties on Anti-scoring Performance of Gears
- ON THE EFFECT OF THE TOOTH PROFILE MODIFICATION ON THE DYNAMIC LOAD AND THE SOUND LEVEL OF THE SPUR GEAR
- ON THE SURFACE TEMPERATURE RISE AT THE FOUR-BALL TESTS
- On the Bending Stress of a Spur Gear : 2nd Report, The Stress Concentration Factor and the Equation for the Calculation of Bending Stress of a Gear Tooth
- Basic Studies on Scoring of Spur Gears : 4th Report, Effect of Module on Scoring Resistance
- On the Bending Stress of a Spur Gear : 1 st Report, Stress at the Fillet Curve and Inner Stress at the Root of Gear Tooth
- STUDIES ON SCORING OF SPUR GEARS : 3RD REPORT, EFFECT OF THE COEFFICIENT OF ADDENDUM MODIFICATION ON SCORING RESISTANCE
- Dynamic Behavior of Planetary Gear : 1st Report Load Distribution in Planetary Gear
- Studies on the Scoring by Using a Crossed Cylinders Friction Machine : 1st Report, On the Initial Situation of Scoring
- BASIC STUDIES ON SCORING OF SPUR GEARS : 2ND REPORT, EXPERIMENTAL RESULTS USING POWER CIRCULATING GEAR TEST RIG
- Dynamic Behavior of Straight Bevel Gear : 2nd Report, Vibration of Bevel Gears on Rectangular-coordinate
- Analysis of Dynamic Tooth Load on Planetary Gear
- Study on Rippling Failure by the Roller Test : 1st Report, On the Progress and Limit of Rippling Failure
- Effect of Lubricating Oil on Rippling Failure
- Dynamic Behavior of Planetary Gear : 7th Report, Influence of the Thickness of the Ring Gear
- Dynamic Behavior of Planetary Gear : 6th Report, Influence of Meshing-Phase
- Dynamic Behavior of Planetary Gear : 5th report, Dynamic Increment of Torque
- On Surface Durability of Involute-cycloid Composite Tooth Profile Gear
- On Design Performance of Involute-cycloid Composite Tooth Profile Gear
- Study on Load-carrying Capacities of Tip-chamfered Gears
- STUDY ON LOAD-CARRYING CAPACITIES OF CARBURIZED GEARS OF BEADED FREE-CUTTING STEEL
- The Mechanism of Seizure in Two-Roller Tests : Vibration, Control Engineering, Engineering for Industry
- Seizure Resistance of Coatings in Four Ball Tests, Two Roller Tests and Gear Tests : Vibration, Control Engineering, Engineering for Industry
- Scoring Resistance of Spur Gears with Various Coatings : 2nd Report, Scoring Tests under Dry Friction
- On the Temperature Rise Caused by Moving Heat Sources : 2nd Report, Calculation of Temperature Considering Heat Radiation from Surface
- Scoring Resistance of Copper-plated Gears
- On the Temperature Rise Caused by Moving Heat Sources : 1st Report, Calculation of the Temperature under Three-dimensional Heat Flow
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 1st Report, The Case of Meshing with a Pair of Ground Standard Gears
- On the Flash Temperature Rise of the Tooth Surface of Surface-Hardened Gear : 1 st Report, Effect of Thermal Conductivity in the Surface Layers of Surface-Hardened Gears
- Basic Studies on Scoring of Spur Gears : 1st Report, On the Seizure under a Pure Sliding Condition and a Sliding-Rolling Condition
- On the Measurement of Temperature Flashes on Spur Gear Teeth : 2nd Report, The Effects of the Amount of Addendum Modification and the Accuracy of Gears on the Tooth Surface Temperature
- Dynamic Behavior of Straight Bevel Gear : 3rd Report, On the Effect of Preloading on Bearing
- A Study on Rolling Finish of Gear : Theoretical Analysis of Number of Contact Points and Plastic Deformations
- A Study on Rolling Finish of Gear : End Effects
- Dynamic Behavior of Planetary Gear : 4th Report, Influence of the Transmitted Tooth Load on the Dynamic Increment Load
- Dynamic Behavior of Planetary Gear : 2nd Report, Displacement of Sun Gear and Ring Gear
- Dynamic Behavior of Planetary Gear : 3rd Report, Displacement of Ring Gear in Direction of Line of Action
- A Study on Rolling Finish of Gear : Plastic Deformations by Rolling Experiment of Rollers