Fundamental on Scoring Failure : 1st report, Initiation and Progress of Scoring on Gear Teeth
スポンサーリンク
概要
- 論文の詳細を見る
In order to clarify the initiation and progress of scoring failure on gear tooth flank, scoring tests were carried out using a gear pair of gear ratio 1. The scoring initiates on one tooth pair and then it proceeds or spreads onto successive tooth pairs and finally it covers all the teeth of the gear. The tooth temperature in relation with the driving time takes a steady, saturated value, when no scoring occurs. But when a scoring occurs, the temperature-time curve shows a point of inflection and diverges. These features of scoring phenomena indicate that the analysis of scoring is to be dealt with as a thermal-stability problem.
- 一般社団法人日本機械学会の論文
著者
-
Kubo Aizoh
Faculty Of Engineering Kyoto University
-
Kubo Aizoh
Faculty Of Engn. Kyoto Univ.
-
Yabe Hiroshi
Faculty Of Engineering Kyoto University
-
Yabe Hiroshi
Faculty Of Engn. Kyoto Univ.
-
Nonaka Tetsuya
Division Of Precision Mechanics Graduate School Of Engn. Kyoto University
-
IWAI Ritsuya
Sumitomo Steel Co. Ltd.
-
Kubo Aizoh
Faculty Of Engineering Kyoto Univ.
関連論文
- On the Running Noise of Toothed Belt Drive : 2nd Report, Influence of Running Condition and Some Noise Reduction Methods
- On the Running Noise of Toothed Belt Drive : 1st Report, Mechanism of Noise Generation
- Effects of Tooth Form on Stresses in Helical Gears : 1st Report, Effects of Convex and Concave Tooth Profiles
- On the Behavior of Magnetic Tape in Self-Acting Foil Bearings
- Development of a New Production System for High-precision, Low-cost Gears of Automobile Manual Transaxles under High-volume Production
- Tooth Fillet Stresses of Gear with Thin Rim : 3rd report, Examination of Approximation Formulae for Gear Tooth Fillet Stresses
- Tooth Fillet Stresses of Gear with Thin rim : 2nd report, Approximation Formulae for Tooth Fillet Stresses
- Tooth Fillet Stresses of Gear with Thin Rim : 1st report, Automatic Meshing for FEM Calculation
- A Computer Based Approach for Evaluation of Operating Performances of Bevel and Hypoid Gears
- Fundamental on Scoring Failure : 2nd report: A Model for Scoring and Critical Temperature
- Fundamental on Scoring Failure : 1st report, Initiation and Progress of Scoring on Gear Teeth
- Tooth Fillet Stresses of Gear with Thin Rim : 5th report, Tooth Fillet and Root Stresses of Internal Spur Gear Supported by Pinned Coupling
- Tooth Fillet Stresses of Gear with Thin Rim : 4th report, Approximation Formulae for Tooth Fillet and Root Stresses of Internal Spur Gear
- Fundamental on Scoring Failure : 3rd Report: Improvement of Scoring Model and Definition of Scoring Index
- A Method for Fast Estimation of the Vibration of Spur Gears : Series C : Vibration, Control Engineering, Engineering for Industry
- A Study on Run-Out Characteristics of Externally Pressurized Gas Journal Bearing : Rotor Run-Out Characteristics
- Theoretical Analysis of Externally Pressurized Porous Journal Gas Bearings : 2nd Report, Journal Bearing with Solid Sleeve Parts
- Theoretical Analysis of Externally Pressurized Porous Journal Gas Bearings : 1st Report
- A Study on Running Accuracy of an Externally Pressurized Gas Thrust Bearing : Load Capacity Fluctuation Due to Machining Errors of the Bearing
- A Study on the Running Accuracy of an Externally Pressurized Gas Thrust Bearing : Bearing Stiffness and Damping Coefficient
- A Study on Characteristics of Externally Pressurized Gas Thrust Bearings with Surface-restriction Compensation : Continued Report ; Dynamic Bearing Characteristics
- A Study on Characteristics of Externally Pressurized Gas Thrust Bearing with Surface-restriction Compensation
- Analysis of Externally Pressurized Thrust Collar Bearings with Slit-Supplies
- Fundamental Characteristics of an Externally Pressurized Gas-lubricated Journal Bearing with Surface-restriction Compensation
- Fundamental Characteristics of an Externally Pressurized Thrust Gas Bearing with Surface-Restriction Compensation through Triangular Restricting Grooves
- Analysis of an Externally Pressurized Thrust Collar Gas-Bearing with Multiple Supply Holes
- A Study on Angular Stiffness and Damping Properties of Externally Pressurized Gas Thrust Bearing with Surface-restriction Compensation
- A Theoretical Investigation on Hydrostatic Bearing
- NUMERICAL COMPARISON AMONG STRUCTURED QUASI-NEWTON METHODS FOR NONLINEAR LEAST SQUARES PROBLEMS
- A Study on the Running Accuracy of an Externally Pressurized Gas Thrust Bearing : Rotor Run-Out Characteristics
- A Study on Run-Out Characteristics of Externally Pressurized Gas Journal Bearing : Modified DF Method for Point-Source Solution
- Current Research on Externally Pressurized Gas-Lubricated Bearings