Mechanism of the Formation of Slag Particles by the Rotary Cylinder Atomization

スポンサーリンク

概要

• 論文の詳細を見る

• Slag is a potential resource of energy and materials because it contains a lot of elements and is at the high temperature of around 1500°C when exhausted.In the previous study, we developed a rotary cylinder atomizing (RCLA) method that can efficiently use the rotation energy for atomizing the molten slag. The minimum diameter of the slag particle was from 10 to 50% of the nozzle diameter. The obtained slag particles were amorphous spheres with high aspect ratios. The higher rotation speed and smaller nozzle diameter could make smaller particles. In the present study, the mechanism of slag particle formation from spouting slag string through the nozzle was investigated using the high-speed camera and the theoretical approach was performed.The slag was string-shaped when spouted from the nozzle. The relationship between the particle diameter (d) and nozzle diameter (2a) was derived as follows:<center>[<a href="http://ess.jstage.jst.go.jp/preview/article/isijinternational/50/9/50_1252/_appendix/1">Equation</a>]</center>Where ρ is density, L is the distance from the center of rotation to the tip of the slag string, Z is rotation speed and γ is surface tension of slag.The flow rate of slag was evaluated using Hagen–Poiseuilles equation and the relationship between the particle diameter and the slag string diameter was obtained using Webers equation. By comparison between the experimental and calculated results, we concluded that a string diameter of 0.2 mm for a 1.3mm nozzle diameter was adequate in this experiment.

• 2010-09-15

著者

• Akiyama Tomohiro

  Center for Advanced Research of Energy Conversion Materials, Hokkaido University

• In-nami Yutaro

  Graduate Student Graduate School Of Engineering Hokkaido Univ.

• Akiyama Tomohiro

  Center For Advanced Research Of Energy Conversion Materials Hokkaido University

• Kashiwaya Yoshiaki

  Graduate School Of Engineering Hokkaido University

• Kashiwaya Yoshiaki

  Faculty Of Engineering Hokkaido University

• Kashiwaya Yoshiaki

  Div. Of Materials Sci. Graduate School Of Engineering Hokkaido Univ.

• Akiyama Tomohiro

  Center For Advanced Research Of Energy And Materials Faculty Of Engineering Hokkaido University

• In-nami Yutaro

  Graduate School Of Engineering Hokkaido University

• Kashiwaya Yoshiaki

  Graduate School Of Energy Science And Technology Kyoto University

関連論文

• Feasibility of an Advanced Waste Heat Transportation System Using High-temperature Phase Change Material (PCM)
• Development of PCM Reactor for Methane Steam Reforming
• Latent Heat of Amorphous Slags and Their Utilization as a High Temperature PCM
• Technology of Latent Heat Storage for High Temperature Application: A Review
• Mechanism of the Formation of Slag Particles by the Rotary Cylinder Atomization
• Development of a Rotary Cylinder Atomizing Method of Slag for the Production of Amorphous Slag Particles
• Technical Feasibility Study of Waste Heat Transportation System Using Phase Change Material from Industry to City
• Vickers hardness of β-SiAlON prepared by a combination of combustion synthesis and spark plasma sintering
• Thermoelectric Properties of Rare Earth-doped SrTiO3 Using Combination of Combustion Synthesis (CS) and Spark Plasma Sintering (SPS)
• Effects of Sintering Temperature on Thermoelectric Device of La-Doped Strontium Titanate in the Combination of Combustion Synthesis and Spark Plasma Sintering
• Thermoelectric Properties of Solution Combustion Synthesized Al-Doped ZnO
• Design of Cascaded Oxide Thermoelectric Generator
• Thermoelectric Properties of Combustion Synthesized and Spark Plasma Sintered Sr_R_xTiO_3 (R = Y, La, Sm, Gd, Dy, 0 < x ≦ 0.1)
• Thermoelectric Properties of Combustion-Synthesized Lanthanum-Doped Strontium Titanate
• Exergy Analysis of Hydriding Combustion Synthesis
• Combustion Synthesis of Doped Lanthanum Gallate as an Electrolyte for Solid Oxide Fuel Cells
• Exergy, CO_2 and Economical Analyses of the Hydrogen Production Using Waste Heat from Molten Slag in the Steel Industry
• Prediction of Granulated Slag Properties Produced from Spinning Disk Atomizer by Mathematical Model
• Characteristics of Glass Beads from Molten Slag Produced by Rotary Cup Atomizer
• Feasibility Study for Recovering Waste Heat in the Steelmaking Industry Using a Chemical Recuperator
• Effect of diluents on high purity β-SiAlONs by mechanically activated combustion synthesis
• Optimization of Sintering Temperature for Maximizing Dimensionless Figure of Merit of La-Doped Strontium Titanate Thermoelectric Material in the Combination of Combustion Synthesis with Post Spark Plasma Sintering
• An Investigation of the Crystallization of a Continuous Casting Mold Slag Using the Single Hot Thermocouple Technique
• Development of Double and Single Hot Thermocouple Technique for in situ Observation and Measurement of Mold Slag Crystallization
• Analysis of the Transition State of the Carbon and Iron Oxide Mixture Activated by Mechanical Milling
• Phosphorous Partition in Dephosphorization Slag Occurring with Crystallization at Initial Stage of Solidification
• Crystallization Behaviors Concerned with TTT and CCT Diagrams of Blast Furnace Slag Using Hot Thermocouple Technique
• Quantitative Estimation of Coupling Phenomenon between Reduction and Gasification on the Facing Pair of Iron Oxide and Graphite
• Characteristics of Nano-reactor and Phenomena during Mechanical Milling of Hematite-Graphite Mixture
• Gas Evolution during Mechanical Milling of Hematite-Graphite Mixture
• Intensive Improvement of Reduction Rate of Hematite-Graphite Mixture by Mechanical Milling
• Reaction Behavior of Facing Pair Between Hematite and Graphite: A Coupling Phenomenon of Reduction and Gasification
• Hydrogen Production from Waste Aluminum at Different Temperatures, with LCA
• In Situ Observation of Reduction Behavior of Hematite with Solid Carbon and Crystallographic Orientation between Hematite and Magnetite
• Simulation Test for Crystallization of Inclusions in Semi-killed Steels during Heat Treatment Prior to Hot Rolling
• Technical Feasibility Study of Waste Heat Transportation System Using Phase Change Material from Industry to City
• Latent Property of Defect-Controlled Metal Oxide : Nonstoichiometric Titanium Oxides as Prospective Material for High-Temperature Thermoelectric Conversion
• Synthesis of Zeolite-X from Waste Metals
• Catalytic Effect of Slags on the Formation of Biodiesel Fuel
• Hydriding Chemical Vapor Deposition of Metal Hydride Nano-Fibers
• In Situ Observation of Diamond Gasification and the Crystallographic Relationship of Graphite Formed on the Surface of Diamond
• Kinetic Analysis of the Gasification of Diamond
• Microstructure Evolution of Iron Carbide during Reaction with Steam at Elevated Temperatures
• Materialographic Investigation on the Mechanism of Hydrogen Production through the Reaction between Iron Carbide and Steam at a Temperature of 673K
• Reduction of Iron Oxides by Nano-Sized Graphite Particles Observed in Pre-Oxidized Iron Carbide at Temperatures around 873K
• Exergy Analysis of Steel Production Processes
• Feasibility of an Advanced Waste Heat Transportation System Using High-temperature Phase Change Material (PCM)
• Development of PCM Reactor for Methane Steam Reforming
• Latent Heat of Amorphous Slags and Their Utilization as a High Temperature PCM
• Technology of Latent Heat Storage for High Temperature Application : A Review
• Effect of Oxides and Carbonate on the Reaction of Hematite and Graphite Mixture Obtained by the Mechanical Milling
• Mechanism of the Formation of Slag Particles by the Rotary Cylinder Atomization
• Development of a Rotary Cylinder Atomizing Method of Slag for the Production of Amorphous Slag Particles
• Exergy Analysis of Methane Steam Reformer Utilizing Steelmaking Waste Heat
• Process Analysis of the Effective Utilization of Molten Slag Heat by Direct Blast Furnace Cement Production System
• Thermodynamic Analysis on the Dust Generation from EAF for the Recycling of Dust
• Thermoelectric Properties of Rare Earth-doped SrTiO_3 Using Combination of Combustion Synthesis (CS) and Spark Plasma Sintering (SPS)
• Glassification and heat recovery system for molten slag
• Decomposition of Biogas into Hydrogen on Hot Slag
• Preface to the "Special Issue on Science and Technologies for the Effective Use of Unrecovered Energy in Steelworks"
• Thermoelectric Properties of Non-stoichiometric Titanium Oxides for Waste Heat Recovery in Steelworks
• Binding Energy of Carbon Implanted into Hematite and in situ Observation of Reaction Behavior during Heating Up Experiment
• Effect of Sulfur on the TTT Diagram of CaO–Al2O3 Slag at Eutectic Composition
• Atmosphere Controlled Hot Thermocouple Method and Crystallization Phenomenon of CaO–Al2O3 Eutectic Slag
• Novel Combustion Route for SrTiO_3 Powders
• Kinetic Analysis of the Decomposition Reaction of CH4 Injecting into Molten Slag
• Latent Property of Defect-Controlled Metal Oxide: Nonstoichiometric Titanium Oxides as Prospective Material for High-Temperature Thermoelectric Conversion
• Size-controlled Ni nanoparticles formation by solution glow discharge
• Thermodynamics of Impurities in Pure Iron Obtained by Hydrogen Reduction
• Simulation of Blast Furnace Operation with Intensive Hydrogen Injection
• A New Route to Synthesize β-SiAION:Eu²⁺ Phosphors for White Light-Emitting Diodes
• Thermodynamics of Impurities in Pure Iron Obtained by Hydrogen Reduction
• Preface to the Special Issue on "Green Energy Ironmaking and Steelmaking –Production of Green Energy and Its Use in Ironmaking and Steelmaking–"

もっと見る 閉じる

スポンサーリンク