Latent Heat of Amorphous Slags and Their Utilization as a High Temperature PCM
スポンサーリンク
概要
- 論文の詳細を見る
In a previous study, a rotary cylinder atomizing (RCLA) method for slag was developed and the slag spouting behavior from a nozzle was investigated. The theoretical approach of the previous study agreed well with the observed result.In this study, the potential of slag particles obtained by RCLA method as a phase changing material (PCM) was investigated.The latent heats and the temperature ranges of heat generation were measured for two kinds of amorphous slags (slag particles and water granulated-slag from blast furnace) using DTA (differential thermal analysis).Mathematical simulation of a countercurrent heat exchanger was performed and the effect of slag latent heat on gas temperature was estimated. The temperature range of the latent heat of amorphous slag was estimated to range from 800 to 950°C. The values of latent heat for slag particles and the water-granulated slag were 294 kJ/kg and 235 kJ/kg, respectively.Simulation results indicated that the latent heat of slag can decrease the temperature of waste gas which might increased the usable kind of waste gas.
著者
-
Kashiwaya Yoshiaki
Graduate School of Engineering, Hokkaido University
-
Akiyama Tomohiro
Center for Advanced Research of Energy Conversion Materials, Hokkaido University
-
In-Nami Yutaro
Graduate Student, Graduate School of Engineering, Hokkaido University
関連論文
- Feasibility of an Advanced Waste Heat Transportation System Using High-temperature Phase Change Material (PCM)
- Development of PCM Reactor for Methane Steam Reforming
- Latent Heat of Amorphous Slags and Their Utilization as a High Temperature PCM
- Technology of Latent Heat Storage for High Temperature Application: A Review
- Mechanism of the Formation of Slag Particles by the Rotary Cylinder Atomization
- Development of a Rotary Cylinder Atomizing Method of Slag for the Production of Amorphous Slag Particles
- Technical Feasibility Study of Waste Heat Transportation System Using Phase Change Material from Industry to City
- Vickers hardness of β-SiAlON prepared by a combination of combustion synthesis and spark plasma sintering
- Crystallization Behaviors Concerned with TTT and CCT Diagrams of Blast Furnace Slag Using Hot Thermocouple Technique
- Thermoelectric Properties of Rare Earth-doped SrTiO3 Using Combination of Combustion Synthesis (CS) and Spark Plasma Sintering (SPS)
- Effects of Sintering Temperature on Thermoelectric Device of La-Doped Strontium Titanate in the Combination of Combustion Synthesis and Spark Plasma Sintering
- Thermoelectric Properties of Solution Combustion Synthesized Al-Doped ZnO
- Design of Cascaded Oxide Thermoelectric Generator
- Thermoelectric Properties of Combustion Synthesized and Spark Plasma Sintered Sr_R_xTiO_3 (R = Y, La, Sm, Gd, Dy, 0 < x ≦ 0.1)
- Thermoelectric Properties of Combustion-Synthesized Lanthanum-Doped Strontium Titanate
- Exergy Analysis of Hydriding Combustion Synthesis
- Combustion Synthesis of Doped Lanthanum Gallate as an Electrolyte for Solid Oxide Fuel Cells
- Exergy, CO_2 and Economical Analyses of the Hydrogen Production Using Waste Heat from Molten Slag in the Steel Industry
- Prediction of Granulated Slag Properties Produced from Spinning Disk Atomizer by Mathematical Model
- Characteristics of Glass Beads from Molten Slag Produced by Rotary Cup Atomizer
- Feasibility Study for Recovering Waste Heat in the Steelmaking Industry Using a Chemical Recuperator
- Effect of diluents on high purity β-SiAlONs by mechanically activated combustion synthesis
- Optimization of Sintering Temperature for Maximizing Dimensionless Figure of Merit of La-Doped Strontium Titanate Thermoelectric Material in the Combination of Combustion Synthesis with Post Spark Plasma Sintering
- Analysis of the Transition State of the Carbon and Iron Oxide Mixture Activated by Mechanical Milling
- Phosphorous Partition in Dephosphorization Slag Occurring with Crystallization at Initial Stage of Solidification
- Crystallization Behaviors Concerned with TTT and CCT Diagrams of Blast Furnace Slag Using Hot Thermocouple Technique
- Quantitative Estimation of Coupling Phenomenon between Reduction and Gasification on the Facing Pair of Iron Oxide and Graphite
- Characteristics of Nano-reactor and Phenomena during Mechanical Milling of Hematite-Graphite Mixture
- Gas Evolution during Mechanical Milling of Hematite-Graphite Mixture
- Intensive Improvement of Reduction Rate of Hematite-Graphite Mixture by Mechanical Milling
- Reaction Behavior of Facing Pair Between Hematite and Graphite: A Coupling Phenomenon of Reduction and Gasification
- Hydrogen Production from Waste Aluminum at Different Temperatures, with LCA
- In Situ Observation of Reduction Behavior of Hematite with Solid Carbon and Crystallographic Orientation between Hematite and Magnetite
- Simulation Test for Crystallization of Inclusions in Semi-killed Steels during Heat Treatment Prior to Hot Rolling
- Technical Feasibility Study of Waste Heat Transportation System Using Phase Change Material from Industry to City
- Latent Property of Defect-Controlled Metal Oxide : Nonstoichiometric Titanium Oxides as Prospective Material for High-Temperature Thermoelectric Conversion
- Synthesis of Zeolite-X from Waste Metals
- Catalytic Effect of Slags on the Formation of Biodiesel Fuel
- Hydriding Chemical Vapor Deposition of Metal Hydride Nano-Fibers
- In Situ Observation of Diamond Gasification and the Crystallographic Relationship of Graphite Formed on the Surface of Diamond
- Kinetic Analysis of the Gasification of Diamond
- Microstructure Evolution of Iron Carbide during Reaction with Steam at Elevated Temperatures
- Materialographic Investigation on the Mechanism of Hydrogen Production through the Reaction between Iron Carbide and Steam at a Temperature of 673K
- Reduction of Iron Oxides by Nano-Sized Graphite Particles Observed in Pre-Oxidized Iron Carbide at Temperatures around 873K
- Exergy Analysis of Steel Production Processes
- Latent Heat of Amorphous Slags and Their Utilization as a High Temperature PCM
- Mechanism of the Formation of Slag Particles by the Rotary Cylinder Atomization
- Development of a Rotary Cylinder Atomizing Method of Slag for the Production of Amorphous Slag Particles
- Exergy Analysis of Methane Steam Reformer Utilizing Steelmaking Waste Heat
- Thermodynamic Analysis on the Dust Generation from EAF for the Recycling of Dust