低熱伝導率難削材のエンドミル加工におけるMQLの工具温度への影響
スポンサーリンク
概要
- 論文の詳細を見る
The effect of minimum quantity lubrication (MQL) method in end milling of stainless steel and titanium alloy that are typical difficult-to-cut materials with coated carbide tool is investigated. The effect is mainly evaluated by tool flank temperature, cutting force and tool wear behavior. The tool flank temperature is measured using a two-color pyrometer with an optical fiber having small measurement area and high response speed under non-contact condition with tool. In MQL cutting of SUS304 and Ti-6Al-4V at cutting speed v=25m/min, the tool flank temperature decreases approximately 50°C and 100°C than the case of dry cutting respectively, and the effect of MQL on tool flank temperature is especially obtained in low-speed cutting. On the other hand, the tool flank temperature in MQL cutting of Ti-6Al-4V is higher than the case of dry cutting in cutting speed v=100m/min or more. In the high-speed cutting of Ti-6Al-4V, it is observed that the several chips adhere on the rake face of cutting edge. In addition, the output voltages from detector are obtained when the adhesion chips on the cutting edge pass through the measurement area of two-color pyrometer. In the case of the SUS304, the feed and thrust force are decreased by the supplying oil mist in high speed cutting. The generation of micro-crack at cutting edge is contained by applying MQL even high speed cutting of Ti-6Al-4V that is not obtained the effect of temperature decreasing.
著者
-
細川 晃
金沢大学理工研究域
-
上田 隆司
金沢大学理工研究域
-
浅川 直紀
金沢大学理工研究域機械工学系
-
岡田 将人
金沢大学理工研究域
-
藤田 祐介
福井工業高等専門学校 教育研究支援センター
-
浅川 直紀
金沢大学理工研究域
関連論文
- レーザ熱処理と切削の複合加工による創生面の摩擦特性 : 静止摩擦特性へおよぼす影響
- cBN工具によるハードミリング : 高速エンドミル加工に関する研究(第2報)
- Ybファイバーレーザによる混合金属粉末の焼結特性に関する研究(第2報) : —焼結状態の定量評価手法の提案—
- 長棒を用いたレーザ誘起衝撃応力の測定 : 歯質の窩洞形成時に生じる衝撃応力(機械要素,潤滑,設計,生産加工,生産システムなど)
- 炭素鋼の正面フライス加工におけるバリの抑制におよぼす被削材のレーザ熱処理の効果
- 旋削加工におけるMQLの効果 : 工具すくい面および逃げ面に供給されるオイルミストの作用機構
- レーザ光を用いたハイブリッド歯科治療--レーザ治療の安全で効率的な臨床応用に向けて
- レーザ光を用いた金属粉末の焼結技術--ラピッドツーリングによる高精度金型の製作に向けて (特集 変わりゆくレーザ・ビーム加工)
- 金属粉末光造形複合加工における小径ボールエンドミルの切削性能
- 旋削加工におけるMQLの効果 : ファイバ連結型2色温度計を用いた工具刃先温度の測定