Automatic Control of Arc Welding (Report IV) : Detection of Cold Lapping
スポンサーリンク
概要
- 論文の詳細を見る
On the so called cold lapping phenomenon which is caused by excessive heat input, the welding condition, the weld result and the mechanism are discussed. The optical method to sense this phenomenon is described.
- 大阪大学の論文
著者
-
ARATA Yoshiaki
Osaka University
-
Inoue Katsunori
Dept. Of Welding Engineering Faculty Of Engineering Osaka Univ.
関連論文
- Plasma Arc Welding of Centrifugal Cast Steel Pipe (HK-40) (Report III)
- High Rate Sputtering of Corrosion-Resistant Alloys(Welding Physics, Processes & Instruments)
- Mechanical Properties on Electron Beam Welds of Constructional High Tension Steels (Report V)
- Studies on Corrosion Behavior of Ceramic Sprayed Stainless Steels (Report II) : Utilization of Anodic Polarization Curves to Evaluate Corrosion Tendency(Materials, Metallurgy & Weldability)
- Studies on Corrosion Behavior of Ceramic Sprayed Stainless Steels (Report I) : Electrochemical Approach on Ceramic Sprayed Coatings(Materials, Metallurgy & Weldability)
- Transient Arc Diagnosis with OMA(Welding Physics, Processes & Instruments)
- High Power Microwave Plasma Beam as a Heat Source (Report IV) : Application to Cutting
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report III) : Effect of Straining Rate on Crack Length in Weld Metal
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report II) : Effect of Straining Rate on Cracking Threshold in Weld Metal during Solidification
- Solidification Crack Susceptibility of Aluminum Alloy Weld Metals (Report I) : Characteristics of Ductility Curves during Solidification by Means of the Trans-Varestraint Test
- Effect of Solidification Rate on Solidification Structure in Weld Metal
- Additional Note on the Report "Quench Hardening and Cracking in Electron Beam Weld Metal of Carbon and Low Alloy Hardenable Steels"
- Quench Hardening and Cracking in Electron Beam Weld Metal of Carbon and Low Alloy Hardenable Steels
- Automatic Control of Arc Welding (Report V) : Application of Digital Picture Processing Technique to Automatic Control
- Automatisierung beim LichtbogenschweiBen : Beobachtung fur kalte Uberlappungen
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report IX) : Effect of Titanium on Solidification Crack Resistance(Materials, Metallurgy & Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VIII) : Effect of Nitrogen on Cracking in SUS 304 Weld Metal(Materials, Metallurgy & Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VII) : Effect of Mn and N on Solidification Crack Resistance(Materials, Metallurgy & Weldability)
- Weld Metal Cracking and Improvements of 25%Cr-20%Ni (AISI 310S) Fully Austenitic Stainless Steel
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report VI) : Effect of La or REM Addition on Solidification Crack Resistance(MATERIALS METALLURGY AND WELDABILITY)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report V) : Solidification Crack Susceptibility and Amount of Phosphide and Sulphide in SUS 310S Weld Metals
- A New Explanation for Role of Delta-Ferrite Improving Weld Solidification Crack Susceptibility in Austenitic Stainless Steel(Materials, Metallurgy, Weldability)
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report IV) : Effect of Decreasing P and S on Solidification Crack Susceptibility of SUS 310S Austenitic Stainless Steel Weld Metals
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report III) : Effect of Strain Rate on Cracking Threshold in Weld Metal during Solidification
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report II) : Effect of Ferrite, P, S, C, Si and Mn on Ductility Properties of Solidification Brittleness
- Solidification Crack Susceptibility in Weld Metals of Fully Austenitic Stainless Steels (Report I) : Fundamental Investigation on Solidification Behavior of Fully Austenitic and Duplex Microstructures and Effect of Ferrite on Microsegregation
- Effects of Horn Connected with Gas Tunnel Type Plasma Spraying Torch
- Gas Tunnel Type Plasma Spraying Apparatus(Welding Physics, Process & Instrument)
- Transferred Type Plasma Jet Using Gas Tunnel(Welding Physics, Process & Instrument)
- Influence of Brazing Condition on Shear Strength of Alumina-Kovar Joint Made with Amorphous Cu_Ti_ Filler Metal
- Corrosion Behavior of Amorphous Fe-Cr-Zr Alloys
- Effect of Chromium Addition on Corrosion Resistance of Amorphous Co-Zr Alloys
- ECR Plasma in a High Power Millimeter-Wave Beam (Report IV) : Contribution of Higher Harmonic Resonance Heating(Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report III) : Difference in Plasma Property by Axial and Radial Launches(Welding Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report II) : Time Variation of Electron Density(Welding Physics, Process & Instrument)
- ECR Plasma in a High Power Millimeter-Wave Beam (Report 1)(Welding Physics, Process & Instrument)
- Electron Beam Melting of Aluminum Alloy by Beam Oscillation(Physics, Process, Instrument & Measurement)
- Dynamic Observation of Beam Hole during Electron Beam Welding in Carbon Steel(Welding Physics, Process & Instrument)
- Tandem Electron Beam Welding (Report V)(Welding Physics, Processes & Instruments)
- Electric Field Assisted Treatment of Various Plasma Sprayed ZrO_2 Coatings(Physics, Process, Instruments & Measurements)
- Untersuchung zum MetallschmeltzprozeB im ElektronenstrahlschweiBen
- Influence of Plasma Spray Conditions on the Structure of Al_2O_3 Coatings(Surface Processing)
- Porosity Measurement of Ceramic Coating by Image Processing Method(Physics, Process, Instrument & Measurement)
- Fracture Behavior of Plasma Sprayed Ceramic Coatings in Scratch Test(Physics, Process, Instrument & Measurement)
- Effect of Spraying Condition on Ceramic Coating Quality in Gas Tunnel Type Plasma Spraying(Physics, Process, Instrument & Measurement)
- Study on the Strength of Explosive Plugged Part under the Environment of Steam Generator
- Uber Eigenschaften von Stopselteil Explosiver Haftung durch WarmestoB(Mechanics, Strength & Structural Design)
- Characteristics of Metal Electroplating to Plasma Sprayed Ceramic Coatings(Physics, Process, Instrument & Measurement)
- Struktur der Al_2O_3 Schichten nach dem Gas Tunnel Plasma-Spritzgerat(Physics, Process, Instrument & Measurement)
- Deposit Characteristics of Sprayed Powder by Gas Tunnel Type Plasma Spraying Apparatus(Physics, Process & Instrument)
- Basic Studies on Plasma Sprayed Ceramics Coatings (Report 1) : Erosion Mechanism at ACT-JP Process(Materials, Metallurgy & Weldability)
- Dynamic Characteristics of Variable Frequency Pulsed TIG Arc(Welding Physics, Process & Instrument)
- Experimental Study on Dynamic Properties of Power Sources for MIG/MAG Welding(Welding Physics, Process & Instrument)
- Pressure Distribution and Basic Properties of Gas Tunnel Type Plasma Jet Torch(Welding Physics, Process & Instrument)
- Study on Characteristics of Weld Defect and its Prevention in Electron Beam Welding (Report IV) : Relationship between Weld Defect and its Formation Phenomenon
- Study on Characteristics of Weld Defect and its Prevention in Electron Beam Welding (Report III) : Characteristics of Cold Shut
- Study on Characteristics of Weld Defect and Its Prevention in Electron Beam Welding (Report II) : Some Metallurgical Features of Weld Porosities
- Diffusion Welding of Titanium to Mild Steel
- Study on Characteristics of Weld Defect and Its Prevention in Electron Beam Welding (Report I) : Characteristics of Weld Porosities
- Effect of Assist Gas on Bead Formation in High Power Laser Welding(Welding Physics, Process & Instrument)
- High Power CO_2 Laser Welding of Thick Plate : Multipass Weding with Filler Wire(Welding Physics, Process & Instrument)
- Weldability of 18%Ni Maraging Steel (HT 210) by Ultra High Voltage Electron Beam Welding(Materials, Metallurgy & Weldability)
- Bonding of Al_2O_3 to SS41 Steel with LPC Plasma Sprayed Cu-Ti Two-layer Coatings(Surface Processing)
- Fundamental Studies on Electron Beam Welding of Heat resistant Superalloys for Nuclear Plants (Report IV) : Effect of High Temperature He on the Properties of Weld Joints(Materials, Metallurgy, Weldability)
- Fundamental Studies of Electron Beam Welding of Heat-resistant Superalloys for Nuclear Plants (Report 5) : Mechanical Properties of Welded Joint
- Fundamental Studies on Electron Beam Welding of Heat-resistant Superalloys for Nuclear Plants (Report 4) : Temperature and Stress Distribution during Welding
- Fundamentale Studien zum ElektronenstrahlschweiBen von Hitzebestandigen Legierungen fur Kernkraftanlagen (Bericht 3) : Metallurgische Betrachtungen uber MikroriB
- Fundamental Studies on Electron Beam Welding of Heat-resistant Superalloys for Nuclear Plants (Report II) : Correlation between Susceptibility to Weld Cracking and Characteristics in Hot Ductility and Trans-Varestraint Test
- Fundamental Studies on Electron Beam Welding of Heat-resistant Superalloys for Nuclear Plants (Report I) : Effect of Welding Conditions on Some Characteristics of Weld Bead
- Study on Electron Beam Welding of Dissimilar Materials for Nuclear Plant (Report I) : Effect of Welding Conditions on Weld Defects(Welding Physics, Process & Instrument)
- Suppression Mechanism of Overlapping Defects in High Speed TEB Welding
- High Speed Welding of Thin Stainless Steel Plates by Tandem Electron Beam
- Bending Strength of CO_2 Laser Welded Joints of 87-0X1.20980BFF1F4DP+0l_2O_3 Ceramics
- High Power CO_2 Laser Welding of Al_2O_3 Ceramics(Physics, Process, Instruments & Measurements)
- Photoresponse of Plasma Sprayed TiO_2-Rutile Semiconductor(Physics, Process, Instruments & Measurements)
- Formation of YBaCu-O System Superconductor by Thermal Spraying(Materials, Metallugy & Weldability)
- Photoanodic Properties of Plasma Sprayed TiO_2 Coatings(Surface Processing)
- Characteristics of 500kV Ultra-High Voltage Electron Beam Heat Source (Report II) : Deep Penetration by Flat Position Welding(Physics, Process, Instruments & Measurement)
- Electrical Conductivity of Titanium Oxide (Rutile) Plasma Sprayed Coatings(Physics, Process, Instrument & Measurement)
- Tandem Electron Beam Welding (Report IX) : High Speed Tandem Electron Beam Welding(Physics, Process, Instrument & Measurement)
- High Power CO_2 Laser Cutting and Welding of Ceramics(Physics, Process, Instrument & Measurement)
- Characteristics of 600kV Class Ultra High Voltage Electron Beam Heat Source(Physics, Process, Instrument & Measurement)
- Plasma Sprayed Y-Ba-Cu-O System Superconductor
- Solid-State Reaction Bonding of Alumina to Cu-4Ti Alloy(Materials, Metallurgy & Weldability)
- Diffusion Welding of Ti-15%Mo-5%Zr Alloy to Mild Steel (0.06%C)
- Diffusion Welding of Molybdenum to Hastelloy Alloy X
- Shape Decision of High Energy Density Beam
- Das Laser-Schweissen von Aluminium und Alu-Legierungen
- Some Problems on Laser Plasma Control with Argon Assist Gas
- Fundamental Phenomena in High Power CO_2 Laser (Report II) : Vacuum Laser Welding(Welding Physics, Process & Instrument)
- Fundamental Phenomena in High Power CO_2 Laser Welding (Report I) : Atmospheric Laser Welding(Welding Physics, Process & Instrument)
- Intermediary Layer of Titanium Oxide in Al_2O_3/Cu Joint Using Amorphous Cu-Ti Filler Metals
- Non-oxide Ceramics (Si_3N_4, SiC) Joint Made with Amorphous Cu_Ti_ and Ni_Ti_ Filler Metals
- Magnetic Control of Plasma Arc Welding (Report III) : On the Pressure Distribution of Plasma and its Effect on Key-Hole Action
- 100KW Klasse-Elektronenstrahlen-SchweiBtechnologie (Bericht II) : Charakterristik der SchweiBraupen und deren Analyse
- Some Properties of 30KW-Class Electron Beam for Welding
- High Power Microwave Plasma Beam as a Heat Source (Report III) : Energy Absorption Process
- High Power Microwave Plasma Beam as a Heat Source (Report II) : Characteristics of 30kW Plasmatron
- High Power Microwave Plasma Beam as A Heat Source (Report I) : Microwave Plasmotron in Nitrogen Gas
- Some Fundamental Characteristics of Microwave Plasma Beam as a Heat Source (1)