吸音ダクトの減衰量特性について
スポンサーリンク
概要
- 論文の詳細を見る
This paper presents the experimental results of attenuation(ATT)characteristics of some lined and splitter ducts. A rectangular air passage with one or more inner surfaces covered with a fibrous acoustical material is used for the mesurements of ATT. The experimental apparatus is schematically shown in Fig. 1 and 2. The flow resistance of some acoustical materials versus volumetric density is given in Fig. 3. Typical distribution of local sound pressure intensity in a cross section is shown in Fig. 4. The noise reduction rate for the distance along the axis of the duct can be calculated from the integrated mean value of the sound pressure distribution for each section plotted against the distance as shown in Fig. 5. It is shown that the sound pressure linearly decreases with logarithmic distance Z. Fig. 6 to 8 show the experimental results of ATT for various thicknesses of acoustical material, where a dotted line shows the calculated value from the Bruel's formula. The ATT of a lined duct depends primarily on the thickness and the flow resistance value. It is also shown that the peak value of ATT moves to the side of lower frequency with increase of the thickness and flow resistance of the acoustical material. The number of sound waves in an acoustical material can be determined theoretically from the flow resistance value, showing that the number is larger than that of sound in air, because the velocity of sound decreases in the acoustical material. Fig. 9 and 10 show the reduction of wave length in the material as a function of fill-up ratio multiplied by the flow resistance value. The ATT of a lined duct can be expressed by Eq. 3, in which K is defined as the absorption coefficient of the acoustic material. Fig. 11 shows the variation of K with the flow resistance of the acoustical material. Similar experiments were performed for a splitter duct by varying the thickness of acoustical material. A peak of ATT also exists at the wave length of sound nearly equal to the interval of arrangement of the acoustical material as shown in Fig. 14. Fig. 15 and 16 show the variation of the coefficient K of a splitter duct of types D_A and D_B with the flow resistance of acoustial material. Again, the ATT can be estimated from the flow resistance of the acoustical material. The coefficient K are compared in Fig. 17 for lined duct, splitter duct of type D_A and D_<A′> in which each duct is divided by a steel plate along the center line. A practical dissipative type muffler for a boiler fan was designed and constructed based on these results as shown in Fig. 18. The attenuation characteristics of muffler were measured as shown in Fig. 19, where a dotted line shows the designed value. (A chain line and points show the attenuation characteristics of the muffler for an induction fan. ) It is shown that the attenuation characteristics of the dissipative type mufflers can be estimated well by the method described here.
- 社団法人日本音響学会の論文
- 1975-08-01
著者
関連論文
- 噴流の衝突により発生する直管共鳴音に対する低減法
- 417 曲がり管内の流動解析と発生騒音に関する研究(流体工学I)
- 内燃機関の騒音と消音器に関する調査研究分科会報告
- 軸対称噴流 : 直管系で生じる自励音の金網による抑制効果(液体工学III)
- 金網に衝突する噴流せん断層の自励振動
- 直管前縁に衝突する円形噴流せん断層の自励振動 : 自励音の特性に及ぼす初期条件の影響 : 流体工学,流体機械
- 134 斜めに切断した直管に衝突する軸対称噴流せん断層の自励振動(流体解析)
- 噴流せん断層の衝突による直管の自励音特性
- 有限長直管前縁に衝突する軸対称噴流せん断層の自励振動現象(オフセットによる効果)
- 噴流せん断層に直交して置かれた矩形管の自励音の特性
- 2410 流れに直交しておかれたフィン付円柱の抗力特性(OS15 流体工学(衝撃波、液体微粒化など))
- 思いつくままに
- ガスタービンの発展を願って
- 吹き出しのあるはく離域における熱伝達--フェンス後方のはく離域
- 吹き出しのあるはく離域における熱伝達--円柱背面のはく離域
- 重畳磁場レビテーションにおける柱状晶/等軸晶組織の遷移
- 介在物近傍における凝固界面変形のX線による観察
- 216 直管に衝突する軸対称噴流せん断層の自励振動現象 : 直管径がノズル径と異なる場合の自励振動現象
- 215 平頭物体に衝突する軸対称噴流せん断層の自励振動現象 : 第二報 物体前縁部形状の及ぼす影響
- 223 平頭物体に衝突する軸対称噴流せん断層の自励振動現象(噴流・火災)
- 日米機械学会原子動力懇談会
- 重力鋳造の湯流れシミュレーションにおける湯口境界条件の設定
- 217 音波励起された円形衝突噴流の流動特性 : 第二報音波ノズル位置の影響
- 222 音波励起された円形衝突噴流の流動特性(噴流・火災)
- 113 熱による気柱の振動現象(伝熱・シミュレーション)
- 416 曲がり管における気流音特性(流体工学I)
- 気液二相境界層の壁面摩擦に関する研究
- 気液二相境界層の壁面摩擦に関する研究
- 円形噴流せん断層の自励振動に伴うロックイン現象(流体工学, 流体機械)
- 1109 溝付き管内の流れにより生じる空力音について(G.S.9 流体工学II)
- 溝付き棒を有する管内空気流れで発生する音に関する研究
- 円形噴流・直管系での自励振動および共鳴に対する金網の影響
- 円形噴流の衝突による共鳴発生に関する一考察
- 金網に衝突する噴流せん断層の自励振動
- 円形噴流の金網への衝突時における自励振動に関する研究(第2報)速度変動のスペクトル成分に関する分析
- リングに衝突する軸対称噴流せん断層の自励振動
- 円管内乱流伝熱に対する脈動の影響に関する実験的研究 : 第2報,位相平均特性
- 円管内乱流伝熱に対する脈動の影響に関する実験的研究 : 第1報,時間平均特性
- 噴流せん断層の衝突による直管共鳴音に対する低減法
- 軸対称噴流-直管系の自励振動現象--かく乱の周波数の固定化と共鳴現象の関係
- 超臨界圧流体における強制対流層流熱伝達へ及ぼす浮力の影響
- 超臨界圧流体の強制対流層流熱伝達に及ぼす浮力の影響(第2報:垂直平板における実験的考察)
- 吸収形消音器の消音特性 : 第1報, 繊維状吸音材の音響特性について
- 2206 リターン形消音器で発生する気流音特性(OS3 流れの実験解析(2))
- (7)臨界点付近の流体の管内強制対流熱伝達 : (a)第1報,超臨界圧流体の場合,(b)第2報,亜臨界圧流体の場合,(c)第3報,第2の伝熱形態について(日本機械学会賞(昭和50年度)審査経過報告)
- 回転円板式人工肺に関する研究 : 第2報, 静脈血液層への酸素ガス吸収について
- 回転円板式人工肺に関する研究 : 第1報, 回転円板上に形成される液膜の性質, およびこの液膜によるガス吸収について
- 音波で励起された円形衝突噴流の円板熱伝達特性 : 熱工学,内燃機関,動力など
- 124 音波励起された円形衝突噴流の平板熱伝達特性(熱移動II)
- 収縮路内での流れのはくり域における熱伝達
- 突起物のある壁面の乱流熱伝達-第2報:突起物後方の流れと熱伝達率について-
- 拡大路における熱伝達現象
- 凸起部のある壁面の乱流熱伝熱(第1報:平板乱流の場合)
- 波型加熱板の熱伝達
- 超臨界圧流体の強制対流層流熱伝熱に及ぼす浮力の影響(第1報:垂直平板の場合の理論解析)
- 臨界点付近の流体の管内強制対流熱伝達 : 第3報, 第2の伝熱形態について
- 臨界点付近の流体の管内強制対流熱伝達 : 第2報, 亜臨界圧流体の場合
- 臨界点付近の流体の管内強制対流熱伝達 : 第1報, 超臨界圧流体の場合
- 鉛直円管内強制対流乱流熱伝達における自然対流および加熱熱膨張による加速の影響 : 影響の発生限界および影響発生後の速度・温度分布
- 空気膜熱しゃ断に関する研究
- 軸対称噴流-有限長直管の自励振動現象
- 軸対称せん断層の衝突に伴う自励振動現象
- 伝熱の研究に魅せられて
- 耳に聞こえぬ音による公害 : 超低周波騒音のことなど(機械工業の展望)
- 吸音ダクトの減衰量特性について
- 第5回国際伝熱会議が終わって(伝熱小特集号)
- はく離流の熱伝達に関する研究 : 第1報, 一様流中に傾斜して置かれた平板背面の熱伝達
- 垂直平板からの自然対流乱流熱伝達について
- 垂直平板からの自然対流乱流熱伝達について
- 超臨界圧流体の熱伝達に関する研究 : 第1報, 炭酸ガスによる実験と簡易計算法の提案
- 超臨界圧流体の熱伝達に関する研究 : 第1報,炭酸ガスによる実験と簡易計算法の提案
- 114 密閉容器内で生じる自然対流の振動現象 : 線熱源がオフセットされた場合(伝熱・シミュレーション)
- 音波で励起した衝突噴流による平板熱伝達の増進(熱工学II)
- スリットを有する物体の抗力特性に関する研究
- 113 線熱源を有する密閉容器内の自然対流のゆらぎ現象 : 第一報, 壁の熱的境界条件が振動に及ぼす影響
- 111 スリットを有する物体の抗力特性に関する研究
- 205 流れ方向に Y 字形スリットを有する円柱の抗力特性
- 112 病院のコージェネレーションシステムに関する一考察
- 164 製鉄所における騒音とその対策(計測・試験・分析, 加工・性質, 日本鉄鋼協会 第 83 回(春季)講演大会)
- 固体触媒面における熱および物質伝達 : 高速触媒反応の新しい測定法
- 固体触媒面における熱および物質伝達 : 高速触媒反応の新しい測定法
- 凸起部のある壁面の乱流熱伝達
- 軸対称噴流-直管系の自励振動現象
- 消音器における気流音と損失水頭の予測
- 吸収形消音器の消音特性 : 第2報, 複素伝搬定数を利用した考察
- 機械工学の国際交流について
- 伝熱工学の国際交流によせて(熱工学小特集号)
- 昭和41年度日本機械学会賞審査経過報告
- 昭和41年度日本機械学会賞審査経過報告
- 炭酸ガスと水蒸気のバンドふく射率
- 炭酸ガスと水蒸気のバンドのふく射率
- 輝炎のふく射機構に関する研究
- 第43期会長退任のあいさつ
- 輝炎のふく射機構に関する研究
- 弔辞
- 第43期会長就任の辞
- 機械から出る騒音の軽減(空気機械の騒音防止)
- 高温ガスタービン蒸気タービン複合サイクル機関
- 大気汚染の問題(大気汚染とその対策)
- 高温ガスタービン機関の研究