GI-1 TRANSMISSION ERROR ANALYSIS WITH ECCENTRICITY OF INVOLUTE CYLINDRICAL GEARS(GEAR INSPECTION)
スポンサーリンク
概要
- 論文の詳細を見る
Exact analytical solutions of transmission errors with eccentricities of involute cylindrical gears are proposed. Analytical equations to obtain transmission errors with eccentricities are derived shortly. The influence of the center distance errors, the ratio of eccentricities and phase differences is investigated under no load. In addition, transmission errors including eccentricities of a pair of spur gear are measured under no loading condition. The results show that the measured and calculated transmission errors agree with each other and the analysis is verified accurately. The influence of center distance errors is so little as to be neglected comparing to the amount of transmission errors. The sum of eccentricities is related to the peak-to-valley value of transmission errors and the ratio of eccentricities is related to waveforms of transmission error curves. Phase difference of eccentricities has a little influence on transmission errors, but it is not negligible comparing to the amount of transmission error caused by tooth flank topography and tooth deflections. For further applications, the analysis can be used to remove waviness from transmission error curves as the filtering technique.
- 一般社団法人日本機械学会の論文
- 2001-11-15
著者
-
Kurokawa Syuhei
Department of Mechanical Engineering, Graduate School of Engineering,Kyushu University
-
Ariura Yasutsune
Department Of Intelligent Machinery And Systems Kyushu University
-
Kurokawa Syuhei
Department Of Intelligent Machinery And Systems Kyushu University
-
ARIURA Yasutsune
Department of Intelligent Machinery and Systems, Kyushu University
関連論文
- GM-06 TRANSIENT PHENOMENON OF CHIP GENERATION AND ITS MOVEMENT IN HOBBING : JAMMING OF CHIP FORMED IN GENERATING ON FINISHED SURFACE IN FLYTOOL SIMULATION TESTS(MANUFACTURING OF GEARS)
- GM-4 TRANSIENT PHENOMENON OF CHIP GENERATIONS AND MOVEMENTS IN HOBBING(GEAR MANUFACTURING)
- GSD-21 A FUNDAMENTAL STUDY ON THE SURFACE DURABILITY OF AUSTEMPERED DUCTILE IRON (ADI) GEARS IN LONG LIFE REGION(GEAR STRENGTH AND DURABILITY, INCLUDING GEAR MATERIALS AND HEAT TREATMENT TECHNIQUES)
- A Tooth Surface Finishing Method with a New Tool of a Vitrified Cubic Boron Nitride Wheel for Involute Internal Spline
- Tungsten Film Chemical Mechanical Polishing Using MnO2 Slurry
- GM-7 A TOOTH SURFACE FINISHING METHOD WITH A NEW TOOL OF A VITRIFIED CUBIC BORON NITRIDE WHEEL FOR INVOLUTE INTERNAL SPLINE(GEAR MANUFACTURING)
- GDN-01 INFLUENCE OF GEAR ECCENTRICITY ON SIDEBANDS OF MESH FREQUENCY : DERIVATION AND DETECTION OF AMPLITUDE MODULATION BY TRANSMISSION ERROR MEASUREMENT(DYNAMICS AND NOISE PROBLEMS OF GEARS AND GEAR BOXES)
- GI-1 TRANSMISSION ERROR ANALYSIS WITH ECCENTRICITY OF INVOLUTE CYLINDRICAL GEARS(GEAR INSPECTION)
- Dielectric SiO Planarization Using MnO Slurry
- Frictional Characterization of Chemical–Mechanical Polishing Pad Surface and Diamond Conditioner Wear
- Fast Diffusion of Water Molecules into Chemically Modified SiO_2 Films Formed by Chemical Vapor Deposition
- Real-Time Evaluation of Tool Flank Wear by In-Process Contact Resistance Measurement in Face Milling
- Performance Evaluation Method of Chemical Mechanical Polishing Pad Conditioner Using Digital Image Correlation Processing
- Effect of Groove Pattern of Chemical Mechanical Polishing Pad on Slurry Flow Behavior
- Study on Factors in Time-Dependent Dielectric Breakdown Degradation of Cu/Low-$k$ Integration Related to Cu Chemical–Mechanical Polishing
- Derivation of Path of Contact and Tooth Flank Modification by Minimizing Transmission Error on Face Gear