コイルばねのたわみ係数に関する一実験
スポンサーリンク
概要
- 論文の詳細を見る
In the deflection formula of a coiled spring δ=η(8D Pn)/(Gd), the different values of correcting factor η have been obtained by several authors for the small values of index D/d. Authors made experiments in order to determine a dependable value of η using steel and piano wire helical springs. In the above formula, d, D and G are the constants determined uniquely if the type and the dimension of the spring are given as to the material. The number of effective coils n is N-2, N being the total number of coils, and δ is the deflection of the helical spring obtained under the action of axial load P. Two correcting factors were considered as follows : η_t is the correcting factor for the case where the total deflection of the spring is considered. η_1 is the correcting factor when only one coil in the middle section of the spring is considered in relation to deflection. We conducted some experiments on helical springs with various materials, types and dimensions. First, the modulus of rigidity G of the wire was measured. Then the relation between load and deflection were obtained for the whole coils of spring and for the middle one coil with no effect of the ends. The changes of the diameter D of the coil under various loads were also measured. The results obtained are as follows : (1) η_t is smaller than unity for small values of D/d, but it become larger than unity for larger values of D/d. (2) η_1 is smaller than η_t by about 0.02. And they all tend to become constant for large values of D/d. (3) The manner in which the values of η_1 change matches well with the result given by Gohner. (4) It is concluded that as the deflection factor for small helical springs, Gohner's one may be properly used.
- 社団法人日本材料学会の論文
- 1958-10-15
著者
関連論文
- 日本材料学会疲労試験方法規約および同規格解説について : 規格作成のいきさつ
- 不銹鋼の繰返し応力による発熱と強度
- 18-8系ステンレス鋼の切欠クリープ破断強度について
- 17-7PHステンレス鋼の応用時効処理による強度変化について
- ねじり加工による残留応力と疲労変形
- 不銹鋼の応力腐食割れに及ぼす加工の影響
- オーステナイト系不銹鋼の高温における二,三の強度特性と組織の変化
- 鋼の応力におよぼす炭素量の影響について
- 炭素鋼の低速捩り疲労変形に及ぼす温度の影響
- 低温焼入による鋼の材質の変化について : 第8報 鋼の時効硬化能と切欠疲労強度
- 低温焼入による鋼の材質の変化について : (第5報)鋼の時効硬化能と疲れ強さ
- 低温焼入による鋼の材質の変化について : (第5報)鋼の時効硬化能と疲れ強さ
- 調質圧延板における不均一形について
- 捩り加工とその恢復 : 第2報 炭素鋼の捩り応力時効処理による機械的性質の変化について
- 深絞り用薄鋼板の調質圧延質下率選定に関する一寄与
- 低温焼入れによる鋼の材質の変化について : (第4報)切欠き疲れ強さの改善
- 低温焼入による鋼の材質の変化について(第3報) : 疲労および衝撃強度の改善
- 調質圧延軟鋼板の圧下率と残留応力とに関する一考察
- 低温焼入による鋼の材質の変化について : (第4報)切欠疲れ強さの改善
- 常温以上の温度で加工した軟鋼の低温焼鈍の影響 (続報)
- 低温焼入による鋼の材質の変化について (第2報) : 中炭素鋼の疲れ強度および衝撃強度
- コイルばねの変形および強度に及ぼす高温セッチング処理の影響
- 繰返圧縮荷重を受けるコイルばねの変形および強さ(第3報) : ピアノ線の場合
- 繰辺圧縮荷重を受けるコイルばねの変形および強さ : 第2報 鋼線ばねについて平均応力の影響
- コイルばねのたわみ係数に関する一実験
- 鋼および鋳鉄の繰返し引張荷重に対する時間強度について
- 銅および鋳鉄の繰返し引張荷重に対する時間強度について
- S45C鋼のねじり塑性疲労寿命に及ぼす平均ひずみの影響
- ひずみ制御下の炭素鋼の重複繰返しねじり塑性疲労 : S45Cの場合
- 重複繰返し荷重下での炭素鋼のねじり塑性疲労 : S45Cの場合
- スポット溶接継手の疲労寿命分布に関する統計的研究(信頼性工学小特集)
- 121 スポット溶接継手の疲労寿命分布に関する統計的一研究(疲労強度)
- 回転曲げ繰返し荷重下におけるアルミナ・セラミックスの確率疲労特性について
- 122 回転曲げ繰返し荷重下におけるアルミナ・セラミックスの確率疲労特性について(疲労・確率疲労特性)
- 表面微小欠陥をもつSCM435丸棒試験片の疲労寿命分布に関する統計的研究
- 高強度鋼の耐久限度線図について
- 122 表面微小欠陥をもつSCM435丸棒試験片の疲労寿命分布に関する統計的研究(疲労寿命)
- 高強度材料の疲労き裂進展に及ぼす板厚効果
- 124 突合せ溶接継手の疲労寿命の分布特性について
- 軸荷重下における S15CK タフトライド処理材の疲労強度
- 軟鋼の応力時効に就いて
- 多層複合板における残留応力測定について(ひずみ法)
- 多層複合板の残留応力測定方法の理論
- 多段重複繰返し応力疲労試験機の試作
- 18-8ステンレス鋼の機械加工層が疲労強度に及ぼす影響について
- 炭素鋼の点溶接継手の両振疲労強度と疲労破壊に関する実験
- サブゼロ引張加工および加工後熱処理による304型18-8不銹鋼の疲労強度改善について
- セラミック-金属接着強度試験片における残留応力の算定式について(比較的厚肉の円筒殻の軸対称曲げ理論の一応用)
- 18-8不銹鋼の高温疲労強度における切欠効果について
- 荷重制御ねじり塑性疲労試験下の塑性ひずみと疲労寿命との関係について
- 新しい塑性ねじり疲労試験機の試作と二段多重重複式試験結果について
- 18%Niマルエージング鋼の疲労強度に及ぼす平均応力の影響
- 鋼線の漸増および漸減応力疲労試験
- 実働荷重疲労試験装置と累積ひん度曲線による二,三の実験
- 繰返し変動ひずみ下でのピアノ線のねじり塑性疲労
- ピアノ線のねじり塑性疲労寿命に及ぼす平均応力の影響
- 重複繰返し荷重下での高炭素のねじり塑性疲労
- 高温における線材の定ひずみ塑性ねじり疲労
- (1-2) 線材の重複荷重ねじり塑性疲労について