OBSERVATION OF CAVITATION FORMATION IN A SUPERPLASTIC Si_3N_<4p>/Al-Mg-Si COMPOSITE AT HIGH STRAIN RATES
スポンサーリンク
概要
- 論文の詳細を見る
Cavitation formation in a high strain rate superplastic Al-Mg-Si composite, reinforced with 20 vol.% Si_3N_4 particulates, was observed by a high resolution scanning electron microscope. The composites were pulled by the tension test under steady true stress at an optimum superplastic deformation condition of 8 MPa and 833 K.Many cavities were formed at/near the interfaces between the matrix and particulates. The number of cavities increased slowly and the growth was so sluggish with increasing strain. The size of most cavities, up to strain of 1.0 at least, were the order of the particulate sizes at nearly 0.5 μM, whereas above strain of 1.4 a few large cavities almost equal to grain sizes appeared by growth and/or interlinkage of the cavities.The large cavities near the highly deformed tip of the failed specimens rapidly grew up and made alignments along the tensile axis.
- 社団法人日本材料学会の論文
- 1995-03-15
著者
-
Mabuchi M
Department Of Energy Science And Technology Graduate School Of Energy Science Kyoto University
-
谷村 眞治
愛知工科大学工学部
-
毛利 哲雄
北大
-
Higashi K
Department Of Metallurgy And Materials Science Graduate School Of Engineering Osaka Prefecture Unive
-
Mabuchi M
Department Of Energy Science And Technology Kyoto University
-
Mabuchi Mamoru
National Industrial Research Institute Of Nagoya
-
IWASAKI Hajime
College of Engineering, Department of Materials Science and Engineering, Himeji Institute of Technol
-
HIGASHI Kenji
College of Engineering, Department of Metallurgy and Materials Science, Osaka Prefecture University
-
TANIMURA Shinji
College of Engineering, Osaka Prefecture University
-
MORI Takasuke
College of Engineering, Department of Mateials Science and Engineering, Himeji Institute of Technolo
-
OHTANI Takuya
College of Engineering, Department of Materials Science and Engineering, Himeji Institute of Technol
-
Ohtani Takuya
College Of Engineering Department Of Materials Science And Engineering Himeji Institute Of Technolog
-
Mori Takasuke
College Of Engineering Department Of Mateials Science And Engineering Himeji Institute Of Technology
-
Mukai Toshiji
Research Center For Advanced Science And Technology University Of Tokyo
-
Tanimura Shinji
College Of Engineering Dept. Mech. Sys. Eng. University Of Osaka Prefecture
-
Higashi Kenji
College Of Engineering Osaka Prefecture University
-
Higashi Kenji
College Of Engineering Department Of Metallurgy And Metallurgy And Materials Science Osaka Prefectur
-
Tanimura Shinji
College of Engin, Dept. Mech. Sys. Engin, Uni, of Osaka Prefecture
関連論文
- 動的引張試験に適した丸棒試験片の形状・寸法に関する検討
- 329 制振部材用低降伏点鋼のひずみ速度およびひずみ経路依存性
- 検力ブロック式試験法による動荷重検出の適用範囲
- 中および高ひずみ速度域での材料試験用試験片の大きさについて
- 822 2,3 の新しい動的材料試験法に関する数値解析による検討
- 直下型地震による大型鋼構造物の過渡応答時における動的応力
- 812 中・高ひずみ速度材料試験における試験片の大きさについて
- 151 発泡ウレタン材充填円管の動的座屈挙動(OS5-4 動的材料変形)(OS5 材料の衝撃強度・損傷に関する最近の知見)
- 612 直下型地震による大型鋼構造物の過渡応答挙動に及ぼす地震記録波形の影響(GS-3 計測・動的問題)
- 29p-F-1 平衡状態図の理論I. 貴金属系合金に対する電子論
- Rh 基 L1_2 型金属間化合物の熱物性(熱膨張係数,熱伝導率)と機械的性質
- Ir,Rh基Ll2金属間化合物 熱膨張係数,熱伝導率 (特集 白金族金属の可能性)
- 金属間化合物NiAlの非化学量論組成における熱伝導度と電気伝導度
- レーザーフラッシュ法による熱伝導率データの信頼性におよぼす試験片の状態の影響
- 29p-N-13 CsCl型2元合金の熱伝導率
- 現象論的計算によるFe-Pt2元系FePt_3及びFePt規則相平衡状態図の評価
- 108 拡散-反応方程式による二重すべり条件下での転位組織の形成過程の解析
- 546 拡散-反応方程式を用いた塑性変形挙動の解析(OS7-7 微視的挙動・効果II)(OS7 微視構造を有する材料の力学)
- 新規化合物探索のための電子論計算に基づくAB二元系化合物の安定性評価と四元系金属間化合物への拡張
- Critical Estimation of Relaxation Coefficient in TDGL Equation Based on Path Probability Method
- Fe-Ni, Fe-Pd, Fe-PtのL1_0相の相安定性、相平衡、相転移の理論
- Kinetics of Glass Transition Simulated by Path Probability Method
- クラスター変分法とフェーズフィールド法の混成化による組織形成の第一原理計算(熱・流体力学・工学におけるマルチスケールモデリング,理学と工学,科学と技術をつなぐマルチスケールモデリング)
- Effect of Annealing on Mechanical Properties and Nanoscale Lamellar Structure in Co-Cu Alloy
- New Step of Ecomaterial to Break through the Barrier between Ecomaterial-Selection and Eco-Design
- Barrier-Free Processing of Materials for Environmentally Benign Life-Cycle Design
- Effects of Pore Characteristics Finely-Controlled by Spacer Method on Damping Capacity of Porous Aluminum
- Ferromagnetic Properties of Co-Cu Alloy with Nanoscale Lamellar Structure
- Effects of Vacancies on Deformation Behavior in Nanocrystalline Nickel
- Comparison of Mechanical Properties of Thin Copper Films Processed by Electrodeposition and Rolling
- Influence of Porosity and Pore Size on Electrical Resistivity of Porous Aluminum Produced by Spacer Method
- Fluid Conductivity of Porous Aluminum Fabricated by Powder-Metallurgical Spacer Method
- Fabrication of Porous Aluminum by Spacer Method Consisting of Spark Plasma Sintering and Sodium Chloride Dissolution
- Effect of Sintering Temperature on Compressive Properties of Porous Aluminum Produced by Spark Plasma Sintering
- Effect of Reduction Ratio of Hot-Extrusion on Microstructures of Superplastic Si_3N_4whisker/Al-Mg-Si Alloy Composites Studied by Transmission Electron Microscopy
- The Effect of Deformation Temperature on Microstructure and Superplastic Flow in Al-Cu-Mg/Si_3N_4p Composites
- Tensile Properties and Blow Forming of 5083 Aluminum Alloy Recycled by Solid-State Recycling
- Blow Forming of Mg Alloy Recycled by Solid-State Recycling
- Corrosion and Mechanical Properties of Recycled 5083 Aluminum Alloy by Solid State Recycling
- An Experimental Investigation of Effects of Specimen Size Parameters on Compressive and Tensile Properties in a Closed Cell Al Foam
- Solid Recycling of an AZ31 Mg Alloy with a Vapor Deposition Coating Layer of High Purity Mg
- Influence of Grain Size on Elongation at Elevated Temperatures in AZ31 Mg Alloy
- Mechanical Properties and Blow Forming of Rolled AZ31 Mg Alloy Sheet
- Tensile Properties of Directionally Solidified AZ91 Mg Alloy
- Tensile Properties from Room Temperature to 673K of Mg-0.9mass%Ca Alloy Containing Lamella Mg_2Ca
- Mechanical Properties and Press Formability at Room Temperature of AZ31 Mg Alloy Processed by Single Roller Drive Rolling
- Superplasticity and Cavitation of Recycled AZ31 Magnesium Alloy Fabricated by Solid Recycling Process
- The Critical Stress at the Interface for Cavity Nucleation in Superplastic Aluminum Matrix Composites Reinforced with Si_3N_4 Particles
- Tensile Properties at Room Temperature to 823K of Mg-4Y-3RE Alloy
- Solid recycling process for magnesium alloys
- Effects of Temperature and Strain Rate on Elongation at Elevated Temperature in Al-4.5Mg Alloy
- Compressive Deformation Behavior at Elevated Temperatures in a Closed-Cell Aluminum Foam
- Elevated Temperature Deformation and Fracture Mechanisms in High-Strain-Rate-Superplastic Si_3 N_/Al-Cu-Mg Composite
- OBSERVATION OF CAVITATION FORMATION IN A SUPERPLASTIC Si_3N_/Al-Mg-Si COMPOSITE AT HIGH STRAIN RATES
- Stress Exponent and Activation Energy in Titanium Aluminides with Different Grain Sizes
- 衝撃摩擦係数測定法とその応用
- 材料の臨界衝撃速度の評価とその薄板加工への応用(衝撃)
- 臨界衝撃速度の応用 : 高速打抜き加工法
- アルミニウム合金の衝撃特性に及ぼす組織的影響因子 : 溶質原子の影響
- 610 ウレタンならびにウレタン充填部材の動的変形特性(GS-3 計測・動的問題)
- Surface Evolution during Focused Iron Beam Micro-Machining in (001) Plane of Single-Crystalline Ni and Amorphous Nickel Alloy
- Bending Properties of Nanocrystalline Ni-18at% W Alloy Produced by Electrodeposition
- Role of the Co Phase in Superplasticity for WC-Co Cemented Carbides
- Effects of the Density on Compressive Properties in Cellular Aluminum Produced by the Sintering Method
- Fabrication of Porous TiAl Intermetallic Compound by Self -propagating High Temperature Synthesis
- Mechanical Properties of Binder-free WC Fabricated by PCS Process
- Compressive Deformation Characteristics of Open-Cell Mg Alloys with Controlled Cell Structure
- Compression Test Simulation of Controlled Cell Shape Open Cellular Magnesium Alloy under Dynamic Loading
- The Grain Size and Texture Dependence of Tensile Properties in Extruded Mg-9Al-lZn
- Forging Characteristics of AZ31 Mg Alloy
- 自動車用衝撃吸収高張力鋼板の開発
- ねじり衝撃を受ける弾性/粘塑性段付棒の動的挙動
- アルミニウム合金の衝撃特性に及ぼす組織的影響因子 : 第二相粒子の分布状態の影響
- Wave Propagation in Transversely Isotropic Fluid-Saturated Poroelastic Media(Solid Mechanics)
- Effects of the WC Grain Size on the Surface Roughness of WC-10%Co Cemented Carbide Micro-Die Machined by FIB
- Superplasticity of a Particle-Strengthened WE43 Magnesium Alloy
- 146 板状溶接試験片の動的引張強度(OS5-3 動的材料強度と構造最適化)(OS5 材料の衝撃強度・損傷に関する最近の知見)
- 611 中・高ひずみ速度域での材料試験用試験片の大きさについて(GS-3 計測・動的問題)
- 609 溶接部材(鋼材)の動的引張強度(GS-3 計測・動的問題)
- 広ひずみ速度域を対象とした各種材料グループに適用し得る実用構成式(衝撃)
- 532 検力ブロック式動的荷重測定法の測定精度
- 531 非共軸ホプキンソン棒衝撃引張試験法における軸力の測定精度の検討
- 検力ブロック式動的負荷試験装置の開発とその実験的検証
- 半無限板の三次元動的熱応力
- 化成皮膜を用いた超塑性・拡散接合プロセスの接合形成挙動の観察
- 斜め衝撃を受ける厚板の動的挙動 : 三次元弾性/粘塑性波動伝ぱ解析
- 衝撃端力検出装置の改良とその応用
- 高速変形特性と材料のミクロ組織
- 結晶粒径の温度依存性を考慮した超塑性変形の構成式の決定
- 331 逆変態により超微細結晶粒化したオーステナイト系ステンレス鋼の高温変形特性(高温変形)
- 228 Al-Ni-Mm-Zr合金の超塑性特性に及ぼす結晶粒径の影響(組織と変形I)
- アルミニウム単結晶の変形挙動に及ぼすひずみ速度の影響
- 電磁軟鉄棒の凸状端変形挙動と発生衝撃力
- Improvement of Crashworthiness in Ultra Lightweight Metallic Foam by Heat-Treatment for Microstructural Modification of Base Material
- Application of Discrete Element Method in Impact Problems
- Newly Developed Testing Techniques to Obtain Dynamic Stress-Strain Curves for a Wide Rnage of Strain Rates
- 3-Dimensional Analysis of Dynamic Behavior of Bearing of Nielsen Bridge(Stress Analysis)
- Effects of Heat Treatment on the Compressive Properties of AZ91 Mg Foam
- Microstructure and Tensile Properties of Rolled Mg-5.5 mass% Zn-0.6 mass% Zr Alloy
- Effects of Cell Geometry on the Compressive Properties of Nickel Foams