Acceleration of curing of resin composite at the bottom surface using slow-start curing methods
スポンサーリンク
概要
- 論文の詳細を見る
The aim of this study was to evaluate the effect of two slow-start curing methods on acceleration of the curing of resin composite specimens at the bottom surface. The light-cured resin composite was polymerized using one of three curing techniques: (1) 600 mW/cm2 for 60 s, (2) 270 mW/cm2 for 10 s+0-s interval+600 mW/cm2 for 50 s, and (3) 270 mW/cm2 for 10 s+5-s interval+600 mW/cm2 for 50 s. After light curing, Knoop hardness number was measured at the top and bottom surfaces of the resin specimens. The slow-start curing method with the 5-s interval caused greater acceleration of curing of the resin composite at the bottom surface of the specimens than the slow-start curing method with the 0-s interval. The light-cured resin composite, which had increased contrast ratios during polymerization, showed acceleration of curing at the bottom surface.
- 日本歯科理工学会の論文
著者
-
Tagami Junji
Cariology & Operative Dentistry Department Of Restorative Dentistry Tokyo Medical And Dental Uni
-
Yoshikawa Takako
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
Morigami Makoto
Department Of Dentistry Toranomon Hospital
-
Sadr Alireza
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Of Medical And Dental Sciences Tokyo Medical And Dental University
-
TAGAMI Junji
Cariology and Operative Dentistry, Department of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University
関連論文
- Relationship between fluorescence loss of QLF and depth of demineralization in an enamel erosion model
- Effect of filler content of flowable composites on resin-cavity interface
- Influence of abrasive particle size on surface properties of flowable composites
- Effect of hybridization on bond strength and adhesive interface after acid-base challenge using 4-META/MMA-TBB resin
- Effects of coating root dentin surfaces with adhesive materials
- Microtensile Bond Strengths of Composite Cores to Pulpal Floor Dentin with Resin Coating
- Microtensile bond strengths of a dual-cure resin cement to dentin resin-coated with an all-in-one adhesive system using two curing modes
- The effect of the elastic modulus of low-viscosity resins on the microleakage of Class V resin composite restorations under occlusal loading
- Inhibition of Biofilm Formation using Newly Developed Coating Materials with Self-cleaning Properties
- Effect of Surface Characteristics on Adherence of S. mutans Biofilms to Indirect Resin Composites
- Surface Properties of Resin Composite Materials Relative to Biofilm Formation
- Effect of Resin Coating on Dentin Bonding of Resin Cement in Class II Cavities
- Dentin bond durability and water sorption/solubility of one-step self-etch adhesives
- Thin resin coating by dual-application of all-in-one adhesives improves dentin bond strength of resin cements for indirect restorations
- Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin
- Effect of PMMA filler particles addition on the physical properties of resin composite
- The acid-base resistant zone in three dentin bonding systems
- Evaluation of dentin bonding performance and acid-base resistance of the interface of two-step self-etching adhesive systems
- Effect of an internal coating technique on tensile bond strengths of resin cements to zirconia ceramics
- Effect of Pulse Duration of Er: YAG Laser on Dentin Ablation
- Dentin Bond Strengths of Three Adhesive/Composite Core Systems using Different Curing Units
- Effect of Light Irradiation Time on the Mechanical Properties of Two Flowable Composites with Different Initiation Systems in Bonded and Unbonded Cavities
- Enhancement of Adhesion between Resin Coating Materials and Resin Cements
- Enamel Bonding of Self-etch and Phosphoric Acid-etch Orthodontic Adhesive Systems
- Effect of Curing Method and Storage Condition on Fluoride Ion Release from a Fluoride-releasing Resin Cement
- Effect of Curing Method of a Dual-cure Resin Cement on Monkey Pulpal Reaction after Bonding of Tooth-colored Inlay
- Relationship between perception of difficulty and clinical experience of approximal composite restorations in final-year undergraduate students at Tokyo Medical and Dental University
- Analysis of Er:YAG Lased Dentin Using Attenuated Total Reflectance Fourier Transform Infrared and X-ray Diffraction Techniques
- Effects of One-year Storage in Water on Bond Strength of Self-etching Adhesives to Enamel and Dentin
- Shear Bond Strength of Tooth-colored Indirect Restorations Bonded to Mid-coronal and Cervical Dentin
- Effect of Pretreatment on Bonding of Resin Cements to Zirconia
- The effect of air-powder polishing on dentin adhesion of a self-etching primer bonding system
- Coronal Leakage Inhibition in Endodontically Treated Teeth Using Resin-coating Technique
- Shear Bond Strengths of Indirect Resin Composites to Hybrid Ceramic
- Influence of Curing Method and Storage Condition on Microhardness of Dual-cure Resin Cements
- Effect of various grit burs on marginal integrity of resin composite restorations
- Effects of light sources and visible light-activated titanium dioxide photocatalyst on bleaching
- Oral health status in relation to stimulated saliva buffering capacity among Japanese adults above or below 35 years of age
- Role of oral streptococci in the pH-dependent carious dentin
- In Vitro pH Analysis of Active and Arrested Dentinal Caries in Extracted Human Teeth Using a Micro pH Sensor
- Microtensile Bond Strength of Dual-cure Resin Cement to Root Canal Dentin with Different Curing Strategies
- Effects of photocuring strategy on bonding of dual-cure one-step self-etch adhesive to root canal dentin
- Regional Bond Strength of Four Self-etching Primer/Adhesive Systems to Root Canal Dentin
- Influence of Elasticity on Gap Formation in a Lining Technique with Flowable Composite
- Effect of Incremental Filling Technique on Adhesion of Light-cured Resin Composite to Cavity Floor
- Effect of Resin Coating on Adhesion of Composite Crown Restoration
- Hardness and Young's Modulus of Transparent Dentin Associated with Aging and Carious Disease
- Effect of Air-powder Polishing on Dentin Adhesion of a Self-etching Primer Bonding System
- Surface Analysis of Dentinal Caries in Primary Teeth using a pH-imaging Microscope
- Effect of composite post placement on bonding to root canal dentin using 1-step self-etch dual-cure adhesive with chemical activation mode
- Effects of water-storage on the physical and ultramorphological features of adhesives and primer/adhesive mixtures
- Effects of Enterococcus faecium on Streptococcus mutans Biofilm Formation Using Flow Cell System
- Human Papillomavirus in Oral Cancer from Sri Lanka : Prevalence and relationship with clinico-pathological parameters
- Retrospective Study of Five-year Clinical Performance of Direct Composite Restorations Using a Self-etching Primer Adhesive System
- The Effect of Thermal Stress on Bonding Durability of Resin Composite Adaptation to the Cavity Wall
- The Effect of Bonding System and Composite Type on Adaptation of Different C-factor Restorations
- Micro-shear Bond Strength of Two All-in-one Adhesive Systems to Unground Fluorosed Enamel
- Evaluation of Antibacterial and Fluoride-releasing Adhesive System on Dentin : Microtensile Bond Strength and Acid-base Challenge
- Effect of Fluoride in Phosphate Buffer Solution on Bonding to Artificially Carious Enamel
- Pulpal Response to a Hybrid Composite Resin Inlay Bonded with a Newly Developed Resin-modified Glass Ionomer Luting Cement
- Effects of Smear Layer and Surface Moisture on Dentin Bond Strength of a Waterless All-in-one Adhesive
- Bonding of Resin to Carious-liked Demineralized Dentin
- New strategy to create "Super Dentin" using adhesive technology : Reinforcement of adhesive-dentin interface and protection of tooth structures
- Studies on the Management of Patients with Xerostomia : Clinical Classification and the Caries Susceptibility of Patients with Xerostomia
- Effect of curing depth of composites on four curing light sources.
- In vivo Dentin Caries Model using Rat Molars
- The influence of light intensities irradiated directly and indirectly through resin composite to self-etch adhesives on dentin bonding
- Roughness and pH changes of enamel surface induced by soft drinks in vitro-applications of stylus profilometry, focus variation 3D scanning microscopy and micro pH sensor
- Effect of smear layer characteristics on dentin bonding durability of HEMA-free and HEMA-containing one-step self-etch adhesives
- Ten-year observation of dentin bonding durability of 4-META/MMA-TBB resin cement-a SEM and TEM study
- Non-destructive assessment of cavity wall adaptation of class V composite restoration using swept-source optical coherence tomography
- Effect of light units on tooth bleaching with visible-light activating titanium dioxide photocatalyst
- Long-term regional bond strength of three MMA-based adhesive resins in simulated vertical root fracture
- Effect of functional monomers in all-in-one adhesive systems on formation of enamel/dentin acid-base resistant zone
- Bonding to caries-affected dentin
- Influence of etching ability of one-step self-etch adhesives on bonding to sound and non-carious cervical sclerotic dentin
- Morphological categorization of acid-base resistant zones with self-etching primer adhesive systems
- 3D evaluation of composite resin restoration at practical training using swept-source optical coherence tomography SS-OCT)
- In vitro effect of hesperidin on root dentin collagen and de/re-mineralization
- Pre-etching vs. grinding in promotion of adhesion to intact enamel using self-etch adhesives
- Effect of lining with a flowable composite on internal adaptation of direct composite restorations using all-in-one adhesive systems
- Effect of air-drying dentin surfaces on dentin bond strength of a solvent-free one-step adhesive
- An approach to normalizing micro-CT depth profiles of mineral density for monitoring enamel remineralization progress
- Effect of remaining dentin thickness on bond strength of various adhesive systems to dentin
- Effect of smear layer treatment on dentin bond of self-adhesive cements
- Development and evaluation of a low-erosive apple juice drink with Phosphoryl-Oligosaccharides of Calcium
- Cariotester, a new device for assessment of dentin lesion remineralization in vitro
- Effect of fluoride concentration in adhesives on morphology of acid-base resistant zones
- Effect of a calcium-phosphate based desensitizer on dentin surface characteristics
- Mineral density, morphology and bond strength of natural versus artificial caries-affected dentin
- Casein phosphopeptide-amorphous calcium phosphate and glass ionomer show distinct effects in the remineralization of proximal artificial caries lesion in situ
- Polymerization behavior within adhesive layer of one- and two-step self-etch adhesives: A micro-Raman spectroscopic study
- Acceleration of curing of resin composite at the bottom surface using slow-start curing methods
- Mineral density, morphology and bond strength of natural versus artificial caries-affected dentin
- Surface characterization of current composites after toothbrush abrasion
- Resistance of dentin coating materials against abrasion by toothbrush
- Cariotester, a new device for assessment of dentin lesion remineralization in vitro
- Development and evaluation of a low-erosive apple juice drink with Phosphoryl-Oligosaccharides of Calcium
- Effects of light curing method and resin composite composition on composite adaptation to the cavity wall
- Effect of fluoride concentration in adhesives on morphology of acid-base resistant zones