Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin
スポンサーリンク
概要
- 論文の詳細を見る
This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal floor dentin were restored with a two-step self-etch adhesive system, Clearfil Liner Bond 2V and a composite core, Clearfil DC Core Automix, using different filling techniques and curing strategies. A flowable resin composite, Clearfil Flow FX was placed on the cured adhesive resin prior to restoration with a composite core. Packing the composite in the access cavity was performed in bulk with or without light curing or using an incremental technique with light curing. Microtensile bond strengths to pulpal floor dentin were measured after 24 hours storage in water. Light curing and incremental technique had positive effects on the MTBSs. Lining with a flowable resin composite did not significantly improve the MTBSs, however, influenced the failure mode after debonding. Non-lining and bulk filling with chemical curing strategy provided the lowest MTBS.
- 2010-09-01
著者
-
TAGAMI Junji
Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and
-
FOXTON Richard
Department of Conservative Dentistry, King's College London Dental Institute at Guy's, King's and St
-
ARIYOSHI Meu
Cariology and Operative Dentistry, Department of Restorative Sciences, Graduate School of Medical an
-
NIKAIDO Toru
Cariology and Operative Dentistry, Department of Restorative Sciences, Graduate School of Medical an
-
Foxton Richard
Department Of Conservative Dentistry King's College London Dental Institute At Guy's King&
-
Nikaido Toru
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Of Medical And
-
Nikaido Toru
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
Nikaido Toru
Cariology And Operative Dentistry Graduate School Tokyo Medical And Dental University
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Of Medical And
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
Tagami Junji
Cariology And Operative Dentistry Tokyo Medical And Dental University
-
Tagami Junji
Cariology & Operative Dentistry Department Of Restorative Dentistry Tokyo Medical And Dental Uni
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
Foxton Richard
Clinical Lecturer Department Of Conservative Dentistry Guy's King's And St. Thomas' D
-
Foxton Richard
Department Of Conservative Dentistry King's College London Dental Institute At Guy's King&
-
Foxton Richard
Department Of Conservative Dentistry Floor 25 Guy's King's And St. Thomas' Dental Ins
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Science Tokyo Medical And Dental Univers
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Tokyo Medical And Dental Univer
-
Foxton Richard
Department Of Conservative Dentistry Floor 25 Guy's King's And St. Thomas' Dental Ins
-
Ariyoshi Meu
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Of Medical And
-
Nikaido Toru
Cariology And Operative Denatistry Department Of Restorative Sciences Graduate School Of Medical And
-
Tagami Junji
Cariology And Operative Denatistry Department Of Restorative Sciences Graduate School Of Medical And
-
Tagami Junji
Cariology And Operative Dentistry Department Of Restorative Sciences Graduate School Tokyo Medical A
-
NIKAIDO Toru
Cariology and Operative Dentistry, Department of Restorative Sciences, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University
関連論文
- Dentin bond durability and water sorption/solubility of one-step self-etch adhesives
- Relationship between fluorescence loss of QLF and depth of demineralization in an enamel erosion model
- Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin
- Effect of filler content of flowable composites on resin-cavity interface
- Influence of abrasive particle size on surface properties of flowable composites
- Effect of hybridization on bond strength and adhesive interface after acid-base challenge using 4-META/MMA-TBB resin
- Effects of coating root dentin surfaces with adhesive materials
- Microtensile Bond Strengths of Composite Cores to Pulpal Floor Dentin with Resin Coating
- Microtensile bond strengths of a dual-cure resin cement to dentin resin-coated with an all-in-one adhesive system using two curing modes
- The effect of the elastic modulus of low-viscosity resins on the microleakage of Class V resin composite restorations under occlusal loading
- Inhibition of Biofilm Formation using Newly Developed Coating Materials with Self-cleaning Properties
- Effect of Surface Characteristics on Adherence of S. mutans Biofilms to Indirect Resin Composites
- Surface Properties of Resin Composite Materials Relative to Biofilm Formation
- Effect of Resin Coating on Dentin Bonding of Resin Cement in Class II Cavities
- Dentin bond durability and water sorption/solubility of one-step self-etch adhesives
- Thin resin coating by dual-application of all-in-one adhesives improves dentin bond strength of resin cements for indirect restorations
- Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin
- Effect of PMMA filler particles addition on the physical properties of resin composite
- The acid-base resistant zone in three dentin bonding systems
- Evaluation of dentin bonding performance and acid-base resistance of the interface of two-step self-etching adhesive systems
- Effect of an internal coating technique on tensile bond strengths of resin cements to zirconia ceramics
- Effect of Pulse Duration of Er: YAG Laser on Dentin Ablation
- Dentin Bond Strengths of Three Adhesive/Composite Core Systems using Different Curing Units
- Effect of Light Irradiation Time on the Mechanical Properties of Two Flowable Composites with Different Initiation Systems in Bonded and Unbonded Cavities
- Enhancement of Adhesion between Resin Coating Materials and Resin Cements
- Enamel Bonding of Self-etch and Phosphoric Acid-etch Orthodontic Adhesive Systems
- Effect of Curing Method and Storage Condition on Fluoride Ion Release from a Fluoride-releasing Resin Cement
- Effect of Curing Method of a Dual-cure Resin Cement on Monkey Pulpal Reaction after Bonding of Tooth-colored Inlay
- Relationship between perception of difficulty and clinical experience of approximal composite restorations in final-year undergraduate students at Tokyo Medical and Dental University
- Analysis of Er:YAG Lased Dentin Using Attenuated Total Reflectance Fourier Transform Infrared and X-ray Diffraction Techniques
- Tensile Bond Strength of a Newly Developed One-bottle Self-etching Resin Bonding System to Various Dental Substrates
- Effects of One-year Storage in Water on Bond Strength of Self-etching Adhesives to Enamel and Dentin
- Shear Bond Strength of Tooth-colored Indirect Restorations Bonded to Mid-coronal and Cervical Dentin
- Effect of Pretreatment on Bonding of Resin Cements to Zirconia
- The effect of air-powder polishing on dentin adhesion of a self-etching primer bonding system
- Coronal Leakage Inhibition in Endodontically Treated Teeth Using Resin-coating Technique
- Shear Bond Strengths of Indirect Resin Composites to Hybrid Ceramic
- Influence of Curing Method and Storage Condition on Microhardness of Dual-cure Resin Cements
- Effect of various grit burs on marginal integrity of resin composite restorations
- Effects of light sources and visible light-activated titanium dioxide photocatalyst on bleaching
- Oral health status in relation to stimulated saliva buffering capacity among Japanese adults above or below 35 years of age
- Role of oral streptococci in the pH-dependent carious dentin
- In Vitro pH Analysis of Active and Arrested Dentinal Caries in Extracted Human Teeth Using a Micro pH Sensor
- Microtensile Bond Strength of Dual-cure Resin Cement to Root Canal Dentin with Different Curing Strategies
- Effects of photocuring strategy on bonding of dual-cure one-step self-etch adhesive to root canal dentin
- Regional Bond Strength of Four Self-etching Primer/Adhesive Systems to Root Canal Dentin
- Influence of Elasticity on Gap Formation in a Lining Technique with Flowable Composite
- Effect of Incremental Filling Technique on Adhesion of Light-cured Resin Composite to Cavity Floor
- Effect of Resin Coating on Adhesion of Composite Crown Restoration
- Hardness and Young's Modulus of Transparent Dentin Associated with Aging and Carious Disease
- Effect of Air-powder Polishing on Dentin Adhesion of a Self-etching Primer Bonding System
- Surface Analysis of Dentinal Caries in Primary Teeth using a pH-imaging Microscope
- Effect of composite post placement on bonding to root canal dentin using 1-step self-etch dual-cure adhesive with chemical activation mode
- Ultrastructural observation of the acid-base resistant zone of all-in-one adhesives using three different acid-base challenges
- Effects of water-storage on the physical and ultramorphological features of adhesives and primer/adhesive mixtures
- Effects of Enterococcus faecium on Streptococcus mutans Biofilm Formation Using Flow Cell System
- Human Papillomavirus in Oral Cancer from Sri Lanka : Prevalence and relationship with clinico-pathological parameters
- Retrospective Study of Five-year Clinical Performance of Direct Composite Restorations Using a Self-etching Primer Adhesive System
- The Effect of Thermal Stress on Bonding Durability of Resin Composite Adaptation to the Cavity Wall
- The Effect of Bonding System and Composite Type on Adaptation of Different C-factor Restorations
- Micro-shear Bond Strength of Two All-in-one Adhesive Systems to Unground Fluorosed Enamel
- Evaluation of Antibacterial and Fluoride-releasing Adhesive System on Dentin : Microtensile Bond Strength and Acid-base Challenge
- Microhardness and Young's Modulus of a Bonding Resin Cured with Different Curing Units
- Effect of Fluoride in Phosphate Buffer Solution on Bonding to Artificially Carious Enamel
- Pulpal Response to a Hybrid Composite Resin Inlay Bonded with a Newly Developed Resin-modified Glass Ionomer Luting Cement
- Reduced Irradiation Time in Slow-curing of Resin Composite Using an Intensity-changeable Light Source
- Effects of Smear Layer and Surface Moisture on Dentin Bond Strength of a Waterless All-in-one Adhesive
- Bonding of Resin to Carious-liked Demineralized Dentin
- The Effects on Puip Tissue of Microleakage in Resin Composite Restorations
- New strategy to create "Super Dentin" using adhesive technology : Reinforcement of adhesive-dentin interface and protection of tooth structures
- Studies on the Management of Patients with Xerostomia : Clinical Classification and the Caries Susceptibility of Patients with Xerostomia
- Effect of curing depth of composites on four curing light sources.
- In vivo Dentin Caries Model using Rat Molars
- The influence of light intensities irradiated directly and indirectly through resin composite to self-etch adhesives on dentin bonding
- Roughness and pH changes of enamel surface induced by soft drinks in vitro-applications of stylus profilometry, focus variation 3D scanning microscopy and micro pH sensor
- Effect of smear layer characteristics on dentin bonding durability of HEMA-free and HEMA-containing one-step self-etch adhesives
- Ten-year observation of dentin bonding durability of 4-META/MMA-TBB resin cement-a SEM and TEM study
- Non-destructive assessment of cavity wall adaptation of class V composite restoration using swept-source optical coherence tomography
- Effect of light units on tooth bleaching with visible-light activating titanium dioxide photocatalyst
- Long-term regional bond strength of three MMA-based adhesive resins in simulated vertical root fracture
- Effect of functional monomers in all-in-one adhesive systems on formation of enamel/dentin acid-base resistant zone
- Bonding to caries-affected dentin
- Influence of etching ability of one-step self-etch adhesives on bonding to sound and non-carious cervical sclerotic dentin
- Morphological categorization of acid-base resistant zones with self-etching primer adhesive systems
- 3D evaluation of composite resin restoration at practical training using swept-source optical coherence tomography SS-OCT)
- In vitro effect of hesperidin on root dentin collagen and de/re-mineralization
- Pre-etching vs. grinding in promotion of adhesion to intact enamel using self-etch adhesives
- Effect of lining with a flowable composite on internal adaptation of direct composite restorations using all-in-one adhesive systems
- Effect of air-drying dentin surfaces on dentin bond strength of a solvent-free one-step adhesive
- An approach to normalizing micro-CT depth profiles of mineral density for monitoring enamel remineralization progress
- Effect of remaining dentin thickness on bond strength of various adhesive systems to dentin
- Effect of smear layer treatment on dentin bond of self-adhesive cements
- Development and evaluation of a low-erosive apple juice drink with Phosphoryl-Oligosaccharides of Calcium
- Cariotester, a new device for assessment of dentin lesion remineralization in vitro
- Effect of fluoride concentration in adhesives on morphology of acid-base resistant zones
- Effect of a calcium-phosphate based desensitizer on dentin surface characteristics
- Mineral density, morphology and bond strength of natural versus artificial caries-affected dentin
- Casein phosphopeptide-amorphous calcium phosphate and glass ionomer show distinct effects in the remineralization of proximal artificial caries lesion in situ
- Polymerization behavior within adhesive layer of one- and two-step self-etch adhesives: A micro-Raman spectroscopic study
- Acceleration of curing of resin composite at the bottom surface using slow-start curing methods