Tin-Doped Resorcinol-Formaldehyde Aerogel with Decanano-Cell Structure
スポンサーリンク
概要
- 論文の詳細を見る
Tin-doped resorcinol-formaldehyde (RF) aerogel was synthesized through immersion of tin (IV) alkoxide in RF gel and drying with supercritical carbon dioxide. The obtained density was 150-280 mg/cm3 , depending on the synthesis conditions. Despite the tin doping, the density is similar to that of undoped aerogel, implying that the shrinkage was suppressed. The cells were ∼50 nm in size, much finer than undoped RF. Such characteristics were discussed as they relate to chelate formation between tin (IV) and RF ligands.
- 社団法人 プラズマ・核融合学会の論文
著者
-
Nagai Keiji
Institute Of Laser Engineering (ile) Osaka University
-
Norimatsu Takayoshi
Institute Of Laser Engineering (ile) Osaka University
-
NAGAI Keiji
Institute of Laser Engineering, Osaka University, Suita, 565-0871, Japan
-
ITO Fuyumi
Graduate School of Science and Engineering, Ritsumeikan University, Kusatsu 525-8577, Japan
-
NAKAMURA Naotake
Graduate School of Science and Engineering, Ritsumeikan University, Kusatsu 525-8577, Japan
関連論文
- Development of HALNA DPSSL for the inertial fusion energy
- Spatial Coherence Measurement of 13.9nm Ni-like Ag Soft X-Ray Laser Pumped by a 1.5ps, 20J Laser
- Drastic Photoluminescence Quenching of Perylene Derivative Membrane with Phthalocyanine Coating
- Manufacturing and Leak Check of Shell Targets for the FIREX-I Project
- A Proposed Procedure for Temperature Control of the Cryogenic Target for the FIREX Project
- Neutral Debris Mitigation in Laser Produced Extreme Ultraviolet Light Source by the Use of Minimum-Mass Tin Target
- Single Molecular Membrane Glue Technique for Laser Driven Shock Experiments : Instrumentation, Measurement, and Fabricagion Technology
- Microstructures of Ultralow-Density Foam Plastics Obtained by Altering the Coagulant Alcohol : Instrumentation, Measurement, and Fabrication Technology
- An Application of Quadrupole to the Handling and Selection of Laser Fusion Fuel Containers
- Density Matched Coating for Laser Fusion Targets
- Selection of Glassmicroballoon and Measurement of Pellet Properties for Laser Fusion Experiments
- Fine Structures of Laser-Driven Punched-Out Tin Fuels Observed with Extreme Ultraviolet Backlight Imaging
- Spatial Coherence Measurement of 13.9 nm Ni-like Ag Soft X-Ray Laser Pumped by a 1.5 ps, 20 J Laser
- Fast-response, low-afterglow 4,4'''-bis〔(2-butyloctyl)oxy〕-1,1':4',1":4",1'''-quarterphenyl dye-based liquid scintillator for high-contrast detection of laser fusion-generated neutrons
- Fabrication of Low-Density Solid Xenon as Laser-Produced Plasma Extreme Ultraviolet Source
- Advanced Target Design for the FIREX-I Project
- Development of Double-Structure Heavy-Element Impurity Pellet for Active Spectroscopy of High-Temperature Plasmas
- Photocathode Kinetics of Phthalocyanine/Fullerene with Respect to the Base Electrode for the Bilayer Coating
- Mechanical Issues of FIREX Target under Cryogenic Environment
- Numerical Study for Laser Source Protection from Alpha Particles by Magnetic Fields in a Laser Fusion Reactor
- Analysis of Parasitic Oscillation and Evaluation of Amplifier Module of Zig-Zag Slab Laser System
- Analysis and Evaluation of Zig-Zag Slab Laser Amplifier with Optical Diamond Geometry
- Extreme Ultraviolet Emission from Laser-Irradiated Low-Density Xe Targets
- Analysis and Evaluation of Laser-Induced Damage of Zig-Zag Slab Laser Amplifier
- Low-Density-Plastic-Foam Capsule of Resorcinol/Formalin and (Phloroglucinolcarboxylic Acid)/Formalin Resins for Fast-Ignition Realization Experiment (FIREX) in Laser Fusion Research
- Experiments on a Gas Gun for Target Injection in Inertial Fusion Energy
- Monochromatic X-Ray Sampling Imager for Laser-Imploded Core Plasma Observation with Highly Spatial, Temporal, and Spectral Resolutions
- Tin-Doped Resorcinol-Formaldehyde Aerogel with Decanano-Cell Structure
- Development of deuterium-tritium loading vessel for laser fusion target.