A Proposed Procedure for Temperature Control of the Cryogenic Target for the FIREX Project
スポンサーリンク
概要
- 論文の詳細を見る
One of the techniques to produce a uniform solid fuel layer for the Fast Ignition Realization EXperiment (FIREX) target is applying a solid fuel redistribution process. During the redistribution process, temperature control is essential for the FIREX target, because a cone guide, also called a conical laser guide, causes temperature non-uniformity. To minimize its temperature distribution, one possible procedure is temperature control at the cone guide. A radiation plate for indirect temperature control, installed next to the cone guide, is proposed. As the heat input to the radiation plate was varied, the temperature profile of the target was calculated using the ANSYS code. The optimal heat input was evaluated. The feasibility of using a radiation plate is discussed.
著者
-
IWAMOTO Akifumi
National Institute for Fusion Science
-
MAEKAWA Ryuji
National Institute for Fusion Science
-
FUJIMURA Takeshi
Institute of Laser Engineering (ILE), Osaka University
-
Nagai Keiji
Institute Of Laser Engineering (ile) Osaka University
-
Norimatsu Takayoshi
Institute Of Laser Engineering (ile) Osaka University
-
Nagai Keiji
Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871, Japan
-
SAKAGAMI Hitoshi
National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292, Japan
-
NAKAI Mitsuo
Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871, Japan
-
NAKAI Mitsuo
Institute of Laser Engineering (ILE), Osaka University, 2-6 Yamada-oka, Osaka 565-0871 Japan
関連論文
- Extension of Improved Particle and Energy Confinement Regime in the Core of LHD Plasma
- 大型ヘリカル装置用超伝導マグネット運転の現状 : 2001年秋
- Development of HALNA DPSSL for the inertial fusion energy
- Low-Density-Plastic-Foam Capsule of Resorcinol/Formalin and (Phloroglucinolcarboxylic Acid)/Formalin Resins for Fast-Ignition Realization Experiment (FIREX) in Laser Fusion Research
- Spatial Coherence Measurement of 13.9nm Ni-like Ag Soft X-Ray Laser Pumped by a 1.5ps, 20J Laser
- Drastic Photoluminescence Quenching of Perylene Derivative Membrane with Phthalocyanine Coating
- Calibration of Compact Electron Spectrometer for the FIREX-I Project in Gekko XII
- Manufacturing and Leak Check of Shell Targets for the FIREX-I Project
- A Proposed Procedure for Temperature Control of the Cryogenic Target for the FIREX Project
- Neutral Debris Mitigation in Laser Produced Extreme Ultraviolet Light Source by the Use of Minimum-Mass Tin Target
- Single Molecular Membrane Glue Technique for Laser Driven Shock Experiments : Instrumentation, Measurement, and Fabricagion Technology
- Microstructures of Ultralow-Density Foam Plastics Obtained by Altering the Coagulant Alcohol : Instrumentation, Measurement, and Fabrication Technology
- An Application of Quadrupole to the Handling and Selection of Laser Fusion Fuel Containers
- Density Matched Coating for Laser Fusion Targets
- Selection of Glassmicroballoon and Measurement of Pellet Properties for Laser Fusion Experiments
- Measurements of Intensity Scaling of Ablation Pressure at 10.6 μm and 1.05 μm Laser Wavelengths
- Fine Structures of Laser-Driven Punched-Out Tin Fuels Observed with Extreme Ultraviolet Backlight Imaging
- Spatial Coherence Measurement of 13.9 nm Ni-like Ag Soft X-Ray Laser Pumped by a 1.5 ps, 20 J Laser
- Fast-response, low-afterglow 4,4'''-bis〔(2-butyloctyl)oxy〕-1,1':4',1":4",1'''-quarterphenyl dye-based liquid scintillator for high-contrast detection of laser fusion-generated neutrons
- Fabrication of Low-Density Solid Xenon as Laser-Produced Plasma Extreme Ultraviolet Source
- Advanced Target Design for the FIREX-I Project
- Development of Double-Structure Heavy-Element Impurity Pellet for Active Spectroscopy of High-Temperature Plasmas
- Photocathode Kinetics of Phthalocyanine/Fullerene with Respect to the Base Electrode for the Bilayer Coating
- Mechanical Issues of FIREX Target under Cryogenic Environment
- Numerical Study for Laser Source Protection from Alpha Particles by Magnetic Fields in a Laser Fusion Reactor
- Analysis of Parasitic Oscillation and Evaluation of Amplifier Module of Zig-Zag Slab Laser System
- Analysis and Evaluation of Zig-Zag Slab Laser Amplifier with Optical Diamond Geometry
- Extreme Ultraviolet Emission from Laser-Irradiated Low-Density Xe Targets
- Analysis and Evaluation of Laser-Induced Damage of Zig-Zag Slab Laser Amplifier
- Low-Density-Plastic-Foam Capsule of Resorcinol/Formalin and (Phloroglucinolcarboxylic Acid)/Formalin Resins for Fast-Ignition Realization Experiment (FIREX) in Laser Fusion Research
- Experiments on a Gas Gun for Target Injection in Inertial Fusion Energy
- Monochromatic X-Ray Sampling Imager for Laser-Imploded Core Plasma Observation with Highly Spatial, Temporal, and Spectral Resolutions
- Tin-Doped Resorcinol-Formaldehyde Aerogel with Decanano-Cell Structure
- Development of deuterium-tritium loading vessel for laser fusion target.