Simulation of Wire EDM under Rough Cutting Conditions(Electrical machining)
スポンサーリンク
概要
- 論文の詳細を見る
This paper describes the development of a simulation method to evaluate the accuracy of rough cutting in WEDM. The simulation program is a repetition of pulse discharge cycle based on the rule that the point where the working gap is shortest is selected as the discharge location. As some of the parameters used in the simulation are difficult to measure from experiments, they are obtained by solving the reverse problem by parametric programming. Investigations were carried out to evaluate simulation accuracy by executing simulation under various machining conditions after substituting identified parameters into the simulator. The simulation results agreed with the experimental ones qualitatively in terms of cutting groove shape, machining speed, and discharge frequency.
- 一般社団法人日本機械学会の論文
- 2005-10-18
著者
-
Kunieda Masanori
Department Of Mechanical System Engineering Tokyo University Of Agriculture And Technology
-
NAKAMURA Kazushi
EDM Systems Department, Nagoya Works, Mitsubishi Electric Corporation
-
TOMURA Shunsuke
Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology
-
UKAI Yoshikazu
EDM Systems Department, Nagoya Works, Mitsubishi Electric Corporation
-
Ukai Yoshikazu
Edm Systems Department Nagoya Works Mitsubishi Electric Corporation
-
Tomura Shunsuke
Department Of Mechanical System Engineering Tokyo University Of Agriculture And Technology
-
Nakamura Kazushi
Edm Systems Department Nagoya Works Mitsubishi Electric Corporation
関連論文
- EDM Using Combined Pulse Lines
- Development of parallel spark electrical discharge machining
- Study on Influence of Stray Capacitance on Micro EDM Using Electrostatic Induction Feeding
- Study on Influence of Stray Capacitance on Micro EDM using Electrostatic Induction Feeding
- D32 Effect of Anisotropy on Shape Measurement Accuracy of Silicon Wafer Using Three-Point-Support Inverting Method(Nano/micro measurement and intelligent instruments)
- Accuracy Estimation of Shape Measurement of Thin-Large Panel with Three-Point-Support Inverting Method
- Accuracy estimation of shape measurement of thin-large panel with three-point-support inverting method(Nano/micro measurement and intelligent instrument)
- Study on Expansion Process of EDM Arc Plasma
- Observation of Temporal Changes of Arc Plasma in EDM(Electrical machining)
- Simulation of Wear of Tool Electrode with Sharp Edges in EDM(Electrical machining)
- Corrosion Problem and Prevention Technology in Wire Electrical Discharge Machining
- Temperature Distribution Measurement in EDM Arc Plasma Using Spectroscopy
- Analysis of electromagnetic force in wire-EDM
- Simulation of Wire EDM under Rough Cutting Conditions(Electrical machining)
- Study on Self-excited Vibration of Wire Electrode in Wire-EDM
- Analysis of Electromagnetic Force in Rough Cutting of Wire-EDM
- Study on thermal equilibrium in EDM arc plasma by spectroscopic analysis
- Generating complicated surface with electrolyte jet machining
- Electrolyte Jet Machining Using Multiple Nozzles
- Effects of support method and mechanical property of 300mm silicon wafer on sori measurement
- Clarifying EDM Gap Phenomena by Gas Chromatography Analysis of Bubbles
- Analysis of Electromagnetic Force in Rough Cutting of Wire-EDM
- Time Variation and Mechanism of Determining Power Distribution in Electrodes during EDM Process
- Study on Dry WEDMed Surface Layer of Cold Tool Steel SKD11
- Reaction Forces Observed in Pulse Discharges of EDM
- Simulation of Die-Sinking EDM by Discharge Location Searching Algorithm
- Factors Determining Discharge Location in EDM
- Challenges in EDM Technology
- Study on the Distribution of Scattered Debris Generated by a Single Pulse Discharge in EDM Process
- Reduction of Tool Wear in Non-contact Electrostatic Induction Feeding EDM
- Study on Debris Movement in EDM Gap
- Clarification of EDM Phenomena by Spectroscopic Analysis
- Electrolysis Free Micro EDM in Water Using Electrostatic Induction Feeding Method