Time Variation and Mechanism of Determining Power Distribution in Electrodes during EDM Process
スポンサーリンク
概要
- 論文の詳細を見る
- 2001-01-01
著者
-
Kunieda Masanori
Department Of Mechanical System Engineering Tokyo University Of Agriculture And Technology
-
HAYAKAWA Shinya
Department of Mechanical Engineering, Nagoya Institute of Technology
-
Nishiwaki Nobuhiko
Department Of Mechanical Systems Engineering Tokyo University Of Agriculture & Technology
-
YUZAWA Masaaki
Department of Mechanical Systems Engineering, Tokyo University of Agriculture & Technology
-
Yuzawa Masaaki
Department Of Mechanical Systems Engineering Tokyo University Of Agriculture & Technology
-
Hayakawa Shinya
Department Of Mechanical Engineering Nagoya Institute Of Technology
-
Hayakawa Shinya
Department Of Mechanical Systems Engineering Tokyo University Of Agriculture & Technology
関連論文
- EDM Using Combined Pulse Lines
- Development of parallel spark electrical discharge machining
- Study on Influence of Stray Capacitance on Micro EDM Using Electrostatic Induction Feeding
- Study on Influence of Stray Capacitance on Micro EDM using Electrostatic Induction Feeding
- D32 Effect of Anisotropy on Shape Measurement Accuracy of Silicon Wafer Using Three-Point-Support Inverting Method(Nano/micro measurement and intelligent instruments)
- Accuracy Estimation of Shape Measurement of Thin-Large Panel with Three-Point-Support Inverting Method
- Accuracy estimation of shape measurement of thin-large panel with three-point-support inverting method(Nano/micro measurement and intelligent instrument)
- Study on Expansion Process of EDM Arc Plasma
- Observation of Temporal Changes of Arc Plasma in EDM(Electrical machining)
- Simulation of Wear of Tool Electrode with Sharp Edges in EDM(Electrical machining)
- Microp-EDM Deposition Alloying Process (第182回電気加工研究会)
- A Study of Fine EDM -Aspects of machining conditions-
- Effect of Bubble Coalescence on Material Removal Rate in Electrical Discharge Machining Process
- Temperature Distribution Measurement in EDM Arc Plasma Using Spectroscopy
- In-Process Measurement and Control of Gap Distance in EDM Process
- Analysis of electromagnetic force in wire-EDM
- Machining Phenomena of Electrical Discharge Machining at Gas-Liquid Interface
- E37 Observation of Scattered Debris Generated by Pulse Discharge in Bubble in Electrical Discharge Machining(Electrical machining)
- Observation of Bubble Expansion and Flying Debris in Parallel Flat Gap Space in Electrical Discharge Machining
- Simulation of Wire EDM under Rough Cutting Conditions(Electrical machining)
- Study on Self-excited Vibration of Wire Electrode in Wire-EDM
- Analysis of Electromagnetic Force in Rough Cutting of Wire-EDM
- Study on thermal equilibrium in EDM arc plasma by spectroscopic analysis
- Generating complicated surface with electrolyte jet machining
- Electrolyte Jet Machining Using Multiple Nozzles
- Effects of support method and mechanical property of 300mm silicon wafer on sori measurement
- Clarifying EDM Gap Phenomena by Gas Chromatography Analysis of Bubbles
- Analysis of Electromagnetic Force in Rough Cutting of Wire-EDM
- Time Variation and Mechanism of Determining Power Distribution in Electrodes during EDM Process
- Study on Dry WEDMed Surface Layer of Cold Tool Steel SKD11
- Reaction Forces Observed in Pulse Discharges of EDM
- Simulation of Die-Sinking EDM by Discharge Location Searching Algorithm
- Factors Determining Discharge Location in EDM
- Challenges in EDM Technology
- Study on the Distribution of Scattered Debris Generated by a Single Pulse Discharge in EDM Process
- Reduction of Tool Wear in Non-contact Electrostatic Induction Feeding EDM
- Effect of Carbon Fiber Orientation on Machining Phenomena in Electrical Discharge Machining of Carbon Fiber Reinforced Plastics
- Effect of Short-Circuiting in Electrical Discharge Machining of Carbon Fiber Reinforced Plastics
- Study on Debris Movement in EDM Gap
- Clarification of EDM Phenomena by Spectroscopic Analysis
- Electrolysis Free Micro EDM in Water Using Electrostatic Induction Feeding Method