Characterization of Wheel Surface Topography in cBN Grinding(<Special Issue>Advanced Manufacturing Technology [I])
スポンサーリンク
概要
- 論文の詳細を見る
The wheel surface topography in the grinding process with vitrified cBN wheels has been investigated on the basis of 3-dimensional analysis using a multi-probe SEM, and the relationships between these results and the grinding characteristic parameters have been discussed. Moreover, the change of the wheel surface profile in the grinding process has been evaluated using fractal analysis. There are two regions: an initial wear region and a steady-state wear region, in the grinding process. In the initial wear region, a rapid decrease of grinding force and a rapid increase of wheel wear occur with increasing stock removal. In the steady-state wear region, the micro self-sharpening phenomenon owing to the micro fracture as well as the attritious wear of cutting edge occurs. The change in fractal dimension of the wheel surface is closely related to the change of grinding force dominated by the wear behavior of grain cutting edges.
- 一般社団法人日本機械学会の論文
- 2006-03-15
著者
-
Morimoto Yoshitaka
Department Of Mechanical Systems Engineering Utsunomiya University
-
Morimoto Yoshitaka
Department Of Applied Chemistry Faculty Of Engineering Osaka Institute Of Technology
-
Fujimoto Masakazu
Graduate School Of Engineering Utsunomiya University
-
ICHIDA Yoshio
Department of Mechanical Systems Engineering, Utsunomiya University
-
SATO Ryunosuke
Department of Mechanical Systems Engineering, Utsunomiya University
-
Ichida Yoshio
Department Of Mechanical Systems Engineering Utsunomiya University
-
Ichida Yoshio
Graduate School Of Engineering Utsunomiya University
-
Ichida Yoshio
Department Of Mechanical And Intelligent Engineering Graduate School Of Engineering Utsunomiya Unive
-
Sato Ryunosuke
Department Of Mechanical Systems Engineering Utsunomiya University
関連論文
- E13 Development of High-Performance Vitrified Grinding Wheels using Ultrafine-Crystalline cBN Abrasive Grains(Grinding technology)
- E12 Microscopic Wear Behavior of Grain Cutting Edges in cBN Grinding(Grinding technology)
- Characterization of Wheel Surface Topography in cBN Grinding(Advanced Manufacturing Technology [I])
- Characterization of Wheel Surface Topography in CBN Grinding(CBN grinding technology)
- Cell Adhesion Scaffold Using Self-assemble β-strand Peptides
- Built up os Stimulus-responsive Hydrogels using Self-assembling β-hairpin Peptides
- Evaluation of Thermally Responsive De Novo Peptides
- OS5(P)-23(OS05W0268) Nanoscratching on Chromium Carbides in Cold Work Die Steel Using an Atomic Force Microscope
- Planar Microfluidic System Based on Electrophoresis for Detection of 130-nm Magnetic Labels for Biosensing
- A26 Mechanism of Material Removal in Nanomachining using AFM Diamond Tip(M4 processes and micro-manufacturing for science)
- Formation Mechanism of Finished Surface in Ultrahigh-Speed Grinding with cubic Boron Nitride (cBN) Wheels(Advanced Manufacturing Technology [I])
- Profile Grinding of Superalloys with Ultrafine-Crystalline cBN Wheels(Advanced Manufacturing Technology [I])
- Real-Time Synthesis and Control by Corrected Inverse Transfer Function of an NC Table(Precision positioning and control technology)
- Development of fine-coarse stage by coaxial arrangement of two stepping motors(Precision positioning and control technology)
- Profile Grinding of Superalloys with Ultrafine-Crystalline CBN Wheels(CBN grinding technology)
- Formation Mechanism of Finished Surface in Ultra-High Speed Grinding with CBN Wheels(CBN grinding technology)
- Effects of Uniformity in Wheel Structure on Grinding Characteristics of Vitrified CBN Wheels(CBN grinding technology)
- OS5(P)-22(OS05W0267) Evaluation of Local Work Affected Layer Based on Magnetic Domain Analysis Using Magnetic Force Microscopy
- 336 Study on accuracy compensation of a machining center based on measurement results of machined workpiece
- Analysis and Contfol of a Flexible Robot Arm by Using Experimental Modal Analysis
- Detection of 8 nm Diameter Superparamagnetic Beads by Magnetically-Induced Manipulation of Micrometer-Sized Magnetic Beads: A Novel Protocol for Magnetically-Labeled Biosensing
- B1 Study on Accuracy Compensation of Machining Center Based on Measurement Results of Machined Workpiece : Evaluation of Accuracy of 5-axis Controlled Machining Center(Advanced machine tool)
- Fractal Analysis of Grain Cutting Edge Wear in Superabrasive Grinding
- Wear Characteristics of Vitrified cBN Grinding Wheels
- Patterning of Two-Dimensional Graphene Oxide on Silicon Substrates
- Chemical Mechanical Polishing for Oxygen Free Copper with Manganese Oxide Abrasives