Study on Near Dry Machining of Aluminum Alloys(<Special Issue>Advanced Manufacturing Technology [I])
スポンサーリンク
概要
- 論文の詳細を見る
Series of orthogonal cutting tests of aluminum alloys have been carried out to investigate the chip formation process and adhesion of the work material to the rake face of the cutting tool under near dry cutting conditions. Almost no adhesion of the work material was observed over a wide range of cutting speed tested when the aluminum alloy was cut with the sintered diamond cutting tool. On the other hand, large amount of adhesion of the work material was observed at low cutting speeds, when cut with the carbide and DLC-coated tools. The amount of the adhered material is reduced with an increase in the cutting speed. The average coefficient of friction on the rake face increases almost in linear relation with the amount of adhesion. The chemical components of the adhered layer were also analyzed by EDS and AES techniques.
- 2006-03-15
著者
-
Ohmae Nobuo
Department Of Mechanical Engineering Faculty Of Engineering Kobe University
-
Ohmae Nobuo
Department Of Mechanical Engineering Kobe University
-
Shimizu Manabu
Engine Production Engineering Div. Toyota Motor Corporation
-
Kinoshita Hiroshi
Department Of Forensic Medicine Faculty Of Medicine Kagawa University
-
Nakai Tetsuo
Headquarters For Innovative Cooperation And Development Kobe University
-
Matsui Makoto
Mechatronics Systems Div. Toyota Motor Corporation
-
Moriwaki Toshimichi
Department Of Mechanical Engineering Kobe University
-
Moriwaki Toshimichi
Department Of Mechanical Engineering Faculty Of Engineering Kobe University
-
YOSHIMURA Hiromi
Engine Production Engineering Div., Toyota Motor Corporation
-
SHIBASAKA Toshiro
Department of Mechanical Engineering, Kobe University
-
Yoshimura Hiromi
Engine Production Engineering Div. Toyota Motor Corporation
-
Kinoshita Hiroshi
Department Of Mechanical Engineering Kobe University
-
Shibasaka Toshiro
Department Of Mechanical Engineering Kobe University
-
Kinoshita Hiroshi
Department Of Bioresource Engineering Faculty Of Agriculture Yamagata University
-
MORIWAKI Toshimichi
Department of Industrial and System Engineering, Setsunan University
関連論文
- Formation of Thin Oxide Films on Room-Temperature Silicon (100) by Exposure to a Neutral Beam of Hyperthermal Atomic and Molecular Oxygen
- Oxidation Properties of Hydrogen-Terminated SI (001) Surfaces Following Use of a Hyperthermal Broad Atomic Oxygen Beam at Low Temperatures : Instrumentation, Measurement, and Fabrication Technology
- The Tribological Characteristics of Ni-Cr Cast Alloy at 1000 Degree C in Air
- Tensile Deformation and Recrystallization in Copper Single Crystal and Bicrystal with Schmid Factor of 0.5
- Effect of Low-Energy Ion Bombardment upon Field-Stimulated Exoelectron Emission from Tungsten Surfaces
- Surface Reaction of a Low-Flux Atomic Oxygen Beam with a Spin-Coated Polymide Film : Synergetic Effect of Atomic Oxygen and Ultraviolet Exposures
- Surface Reaction of a Low Flux Atomic Oxygen Beam with a Spin-Coated Polyimide Film : Translational Energy Dependence on the Reaction Efficiency
- Effects of External Stresses on the Low Temperature Thermal Oxidation of Silicon
- Surface Characterization of Carbon Fibers Exposed to 5 eV Energetic Atomic Oxygen Beam Studied by Wetting Force Measurements
- High growth rate of vertically aligned carbon nanotubes using a plasma shield in microwave plasma-enhanced chemical vapor deposition
- High friction of a vertically aligned carbon-nanotube film in microtribology
- Development of a Circular Vibration Milling Attachment(Advanced machine tool)
- Application of energy dispersive X-ray fluorescent spectrometry (EDXRF) in drug-related cases
- Study on Near Dry Machining of Aluminum Alloys(Advanced Manufacturing Technology [I])
- Study on Near Dry Machining of Aluminum Alloys(Advanced machining technology)
- Synthesis and mechanical properties of carbon nanotube/diamond-like carbon composite films
- Isolation and Structures of Acremolactones B and C, Novel Plant-Growth Inhibitory γ-Lactones from Acremonium roseum I4267
- Absolute Stereochemistry of Acremolactone A, a Novel Herbicidal Epoxydihydropyranyl γ-Lactone from Acremonium roseum I4267
- Precision Grinding of Micro Array Lens Molding Die with 4-axes Controlled Micro Wheel(Ultra-precision machining)
- Decentralized Job Shop Scheduling by Recursive Propagation Method
- Ethanol metabolism in ALDH2 knockout mice - Blood acetate levels
- The application of a variable-pressure scanning electron microscope with energy dispersive X-ray microanalyser to the diagnosis of electrocution : a case report
- Bromide detection in blood using energy dispersive X-ray fluorescence ; a chemical marker supportive of drowning in seawater
- 乗用車内における特異な心中例
- Lack of Association Between Smoking and CYP2A6 Gene Polymorphisms in A Japanese Population
- Concentrations of Carbamazepine(CBZ)and Its Metabolite, CBZ-10, 11-epoxide, in Blood and Urine of a Fatal Case Due to CBZ Ingestion
- Less contribution of the nicotinic cholinergic and α_2-adrenergic action of high acetaldehyde concetration on the inhibition of intestinal ethanol absorption
- Development of Sequential Optimization Method for CNC Turning Based on In-Process Tool Wear Monitoring
- Development of in-Process Tool Wear Monitoring System for CNC Turning
- Comprehensive Monitoring System for Cutting Process(Advanced Manufacturing Technology)
- Detection of metallic elements from paraffin-embedded tissue blocks by energy dispersive X-ray fluorescence spectrometry
- Frictional Properties of Carbon Nanotube Films with a Load Range from Micronewton to Millinewton Using mm Size Balls
- Rapid Removal Volume Acquisition for Tool Posture Decision in 3+2-Axis Control Milling
- Cutting Mechanics of Turning with Actively Driven Rotary Tool