Modeling of Solid Particle Flow in Blast Furnace Considering Actual Operation by Large-scale Discrete Element Method
スポンサーリンク
概要
- 論文の詳細を見る
The objective of this paper is to analyze the solid particle flow in a blast furnace having bell-type charging system by using large-scale Discrete Element Method (DEM). About 500000 particles were calculated in this work. The particle discharging behavior of laboratory-scale blast furnace was compared to confirm the material properties used in the simulation work, and the simulated trajectories of tracer particle correlated with those of experimental very well. The melting behavior of iron ore and combustion of coke in the actual blast furnace were modeled by shrinking particles. The simplified bell-type charging system in this simulation mimicked the actual blast furnace, the collapse of coke layer at the top was observed, and the time change of stock level was quite similar. The particle pulsating flow was observed at the upper area of blast furnace, and the descending velocity near side wall was much larger than that of center in this calculation. The melting position of ore was mapped and the most of iron ore were melting above the raceway. This area should be cohesive zone. This modeling is the first step of the analysis of blast furnace by using Discrete Element Method. Although only contact force was considered and simplified melting zone or raceway were introduced, this large-scale simulation has a high potential to analyze the solid flow in the blast furnace, and the abnormal phenomena or serious problem in blast furnace operation will be analyzed in the future by considering gas flow or heat transfer.
- 社団法人 日本鉄鋼協会の論文
- 2007-12-15
著者
-
Mio Hiroshi
Research Center for Advanced Science and Technology, Doshisha University
-
Shimosaka Atsuko
Department of Chemical Engineering and Materials Science, Doshisha University
-
Shirakawa Yoshiyuki
Department of Chemical Engineering and Materials Science, Doshisha University
-
Hidaka Jusuke
Department of Chemical Engineering and Materials Science, Doshisha University
-
Hidaka Jusuke
Department Of Chemical Engineering And Materials Science Doshisha University
-
Hidaka Jusuke
Department Of Chemical Engineering And Material Science Faculty Of Science Engineering Doshisha Univ
-
Mio Hiroshi
Kyoto Fine Particle Technology, Keihanna Interaction Plaza Inc.
-
Yamamoto Ko
Department of Chemical Engineering and Materials Science, Doshisha University
-
Shirakawa Yoshiyuki
Department Of Chemical Engineering And Materials Science Doshisha University
-
Shirakawa Y
Osaka Univ. Osaka
-
Shirakawa Yoshiyuki
Department Of Materials Science And Processing Faculty Of Engineering Osaka University
-
Hidaka J
Department Of Chemical Engineering And Materials Science Doshisha University
-
Mio Hiroshi
Research Center For Advanced Science And Technology Doshisha University
-
Yamamoto Ko
Department Of Chemical Engineering And Materials Science Doshisha University
-
Shimosaka A
Department Of Chemical Engineering And Materials Science Doshisha University
-
Shimosaka Atsuko
Department Of Chemical Engineering And Materials Science Doshisha University
関連論文
- Analysis of Traveling Behavior of Nut Coke Particles in Bell-type Charging Process of Blast Furnace by Using Discrete Element Method
- Neutron Diffraction Study of Liquid Bi-Se Alloys
- Structural Study of Molten Silver Halides by Neutron Diffraction
- Structures of Molten CuCl,CuBr and CuI
- Solid base catalysis of calcium oxide for a reaction to convert vegetable oil into biodiesel
- Estimation of Separation Efficiency of Metallic Filter Media Based on Pore Size Distribution
- First-Principles Study of Molecule/Al Interfaces
- Estimation of the sieving rate of powders using computer simulation
- Simulation of Mass Flow Rate of Particles Discharged from Hopper by Particle Element Method
- Quantum chemical calculation of electron transfer at metal/polymer interfaces
- Effect of paddle rotational speed on particle mixing behavior in electrophotographic system by using parallel discrete element method
- Diffusion and Cluster Formation near NaCl Solution/Organic Solvent Interface in a Crystallization Process
- Effect of Chute Angle on Charging Behavior of Sintered Ore Particles at Bell-less Type Charging System of Blast Furnace by Discrete Element Method
- Validation of Particle Size Segregation of Sintered Ore during Flowing through Laboratory-scale Chute by Discrete Element Method
- Estimation of Bulk Density Distribution in Particle Charging Process Using Discrete Element Method Considering Particle Shape
- Formation and morphology of asymmetric NaCl particles precipitated at the liquid-liquid interface
- Cell optimization for fast contact detection in the discrete element method algorithm
- Production of Asymmetrical Particles in a Crystallization Process Using Liquid-Liquid Interfaces
- Structural dependence of ionic motion at interfaces between NaCl crystal surfaces and supersaturated solutions in crystallization process
- Modeling of Solid Particle Flow in Blast Furnace Considering Actual Operation by Large-scale Discrete Element Method
- Analysis of Developing Behavior in Two-Component Development System by Large-Scale Discrete Element Method
- Analysis of Separation Characteristics of Rotating Probability Screen
- Effect of interfacial structures on ionic conductivity in particle-dispersed composite electrolytes
- Optimum Cell Condition for Contact Detection Having a Large Particle Size Ratio in the Discrete Element Method
- Optimum Cell Size for Contact Detection in the Algorithm of the Discrete Element Method
- Simulation of flow behavior of a two-component developer in an electro-photographic system
- Electronic Properties of Hybrid Materials Consisting of N-type Nanocrystals and Amorphous Selenium Matrix
- Ultrasonic Velocity and Absorption in Molten Cuprous Halides
- Transport Coefficients in Molten NaCl by Computer Simulation
- Charge Distributions in Liquid Ag-Based Alloys
- Magnetic and Thermodynamical Properties of Liquid Ag-Polyvalent Alloys
- Magnetic Properties of Liquid Ag-In System
- Neutron Diffraction Study on Molten Salt Mixtures; CuCl-CuBr and AgBr-AgI Systems
- Neutron Diffraction Study of Liquid Tl-Se Alloys
- Ultrasonic Velocity and Attenuation of Molten Cupric Halides
- Analysis of Traveling Behavior of Nut Coke Particles in Bell-type Charging Process of Blast Furnace by Using Discrete Element Method
- Effect of Chute Angle on Charging Behavior of Sintered Ore Particles at Bell-less Type Charging System of Blast Furnace by Discrete Element Method
- Validation of Particle Size Segregation of Sintered Ore during Flowing through Laboratory-scale Chute by Discrete Element Method
- Estimation of Bulk Density Distribution in Particle Charging Process Using Discrete Element Method Considering Particle Shape
- Modeling of Solid Particle Flow in Blast Furnace Considering Actual Operation by Large-scale Discrete Element Method
- Preparation of porous particles by liquid-liquid interfacial crystallization
- Estimation of Power during Dispersion in Stirred Media Mill by DEM-LES Simulation
- Simulation of Drying of Particulate Suspensions in Spray-Drying Granulation Process
- Estimation of particle size distribution from cross-sectional particle diameter on the cutting plane
- Revealing the formation mechanism of granules by drying simulation of slurry droplet
- Estimation of Power during Dispersion in Stirred Media Mill by Coupled DEM-LES Simulation
- Solid electrolyte films in controlling their structures by electrophoretic deposition method
- Estimation Equation for Sieving Rate Based on the Model for Undersized Particles Passing through Vibrated Particle Bed
- Protective effect of taurine against ammonia-induced gastric mucosal lesions in rats.
- Heterogeneous nucleation and growth mechanism on hydrophilic and hydrophobic surface