Estimation of Bulk Density Distribution in Particle Charging Process Using Discrete Element Method Considering Particle Shape

スポンサーリンク

概要

• 論文の詳細を見る

• In order to analyze the segregation of coal particles in coke oven, it is necessity to consider the coal shape in Discrete Element Method (DEM). In this paper, the effect of particle shape on the granular flow and on bulk density distribution was investigated, and the novel method for considering particle shape on the void fraction in packed bed was proposed by changing contact distance between particles. The flowing behavior of tablet shaped polystyrene (PS) particles was analyzed and compared with simulation result which was calculated by spherical element or multi-sphere element. The results of flowing velocity and its angle using spherical element and multi-sphere one gave the similar tendency and they were correlated with experimental ones. Thus, the flowing behavior of non-spherical particle can be simulated by spherical element, as long as the suitable parameters were used. The bulk density distribution in horizontal direction in the simulated results using spherical element gave the different tendency of experimental one. On the other hand, those in multi-sphere element and new method showed the similar tendency to the experimental one. Thus, the bulk distribution cannot be simulated by using spherical element. The calculation speed of new method is 4.5 times faster than that of multi-sphere method. This method could be applied to coal packing simulation, and the bulk density distribution by using it had a good correlation with experimental one. Therefore, this method for considering the particle shape on the charged bed is very useful.

• 社団法人 日本鉄鋼協会の論文
• 2008-11-15

著者

• Mio Hiroshi

  Research Center for Advanced Science and Technology, Doshisha University

• Akashi Masatoshi

  Department of Chemical Engineering and Materials Science, Doshisha University

• Shimosaka Atsuko

  Department of Chemical Engineering and Materials Science, Doshisha University

• Shirakawa Yoshiyuki

  Department of Chemical Engineering and Materials Science, Doshisha University

• Hidaka Jusuke

  Department of Chemical Engineering and Materials Science, Doshisha University

• Hidaka Jusuke

  Department Of Chemical Engineering And Materials Science Doshisha University

• Hidaka Jusuke

  Department Of Chemical Engineering And Material Science Faculty Of Science Engineering Doshisha Univ

• Mio Hiroshi

  Kyoto Fine Particle Technology, Keihanna Interaction Plaza Inc.

• Nomura Seiji

  Environment & Process Technology Center, Nippon Steel Corporation

• Shirakawa Yoshiyuki

  Department Of Chemical Engineering And Materials Science Doshisha University

• Shirakawa Y

  Osaka Univ. Osaka

• Shirakawa Yoshiyuki

  Department Of Materials Science And Processing Faculty Of Engineering Osaka University

• Hidaka J

  Department Of Chemical Engineering And Materials Science Doshisha University

• Mio Hiroshi

  Research Center For Advanced Science And Technology Doshisha University

• Akashi Masatoshi

  Department Of Chemical Engineering And Materials Science Doshisha University

• Shimosaka A

  Department Of Chemical Engineering And Materials Science Doshisha University

• Shimosaka Atsuko

  Department Of Chemical Engineering And Materials Science Doshisha University

関連論文

• Analysis of Traveling Behavior of Nut Coke Particles in Bell-type Charging Process of Blast Furnace by Using Discrete Element Method
• Neutron Diffraction Study of Liquid Bi-Se Alloys
• Structural Study of Molten Silver Halides by Neutron Diffraction
• Structures of Molten CuCl,CuBr and CuI
• Solid base catalysis of calcium oxide for a reaction to convert vegetable oil into biodiesel
• Estimation of Separation Efficiency of Metallic Filter Media Based on Pore Size Distribution
• First-Principles Study of Molecule/Al Interfaces
• Estimation of the sieving rate of powders using computer simulation
• Simulation of Mass Flow Rate of Particles Discharged from Hopper by Particle Element Method
• Quantum chemical calculation of electron transfer at metal/polymer interfaces
• Effect of paddle rotational speed on particle mixing behavior in electrophotographic system by using parallel discrete element method
• Diffusion and Cluster Formation near NaCl Solution/Organic Solvent Interface in a Crystallization Process
• Effect of Chute Angle on Charging Behavior of Sintered Ore Particles at Bell-less Type Charging System of Blast Furnace by Discrete Element Method
• Validation of Particle Size Segregation of Sintered Ore during Flowing through Laboratory-scale Chute by Discrete Element Method
• Estimation of Bulk Density Distribution in Particle Charging Process Using Discrete Element Method Considering Particle Shape
• Formation and morphology of asymmetric NaCl particles precipitated at the liquid-liquid interface
• Cell optimization for fast contact detection in the discrete element method algorithm
• Production of Asymmetrical Particles in a Crystallization Process Using Liquid-Liquid Interfaces
• Structural dependence of ionic motion at interfaces between NaCl crystal surfaces and supersaturated solutions in crystallization process
• Modeling of Solid Particle Flow in Blast Furnace Considering Actual Operation by Large-scale Discrete Element Method
• Analysis of Developing Behavior in Two-Component Development System by Large-Scale Discrete Element Method
• Analysis of Separation Characteristics of Rotating Probability Screen
• Effect of interfacial structures on ionic conductivity in particle-dispersed composite electrolytes
• Optimum Cell Condition for Contact Detection Having a Large Particle Size Ratio in the Discrete Element Method
• Optimum Cell Size for Contact Detection in the Algorithm of the Discrete Element Method
• Simulation of flow behavior of a two-component developer in an electro-photographic system
• Electronic Properties of Hybrid Materials Consisting of N-type Nanocrystals and Amorphous Selenium Matrix
• Ultrasonic Velocity and Absorption in Molten Cuprous Halides
• Transport Coefficients in Molten NaCl by Computer Simulation
• Charge Distributions in Liquid Ag-Based Alloys
• Magnetic and Thermodynamical Properties of Liquid Ag-Polyvalent Alloys
• Magnetic Properties of Liquid Ag-In System
• Neutron Diffraction Study on Molten Salt Mixtures; CuCl-CuBr and AgBr-AgI Systems
• Neutron Diffraction Study of Liquid Tl-Se Alloys
• The Characteristics of Catalyst-coated Highly Reactive Coke
• Improvement in Blast Furnace Reaction Efficiency through the Use of Highly Reactive Calcium Rich Coke
• Ultrasonic Velocity and Attenuation of Molten Cupric Halides
• Effects of Coal Inertinite Size on Coke Strength
• Waste plastics recycling process using coke ovens
• Some Fundamental Aspects of Highly Reactive Iron Coke Production
• Analysis of Traveling Behavior of Nut Coke Particles in Bell-type Charging Process of Blast Furnace by Using Discrete Element Method
• Effect of Chute Angle on Charging Behavior of Sintered Ore Particles at Bell-less Type Charging System of Blast Furnace by Discrete Element Method
• Validation of Particle Size Segregation of Sintered Ore during Flowing through Laboratory-scale Chute by Discrete Element Method
• Estimation of Bulk Density Distribution in Particle Charging Process Using Discrete Element Method Considering Particle Shape
• Modeling of Solid Particle Flow in Blast Furnace Considering Actual Operation by Large-scale Discrete Element Method
• Post-reaction Strength of Catalyst-added Highly Reactive Coke
• Preparation of porous particles by liquid-liquid interfacial crystallization
• Estimation of Power during Dispersion in Stirred Media Mill by DEM-LES Simulation
• Simulation of Drying of Particulate Suspensions in Spray-Drying Granulation Process
• Estimation of particle size distribution from cross-sectional particle diameter on the cutting plane
• Enhancement of Low-temperature Gasification and Reduction by Using Iron-coke in Laboratory Scale Tests
• Revealing the formation mechanism of granules by drying simulation of slurry droplet
• Estimation of Power during Dispersion in Stirred Media Mill by Coupled DEM-LES Simulation
• Solid electrolyte films in controlling their structures by electrophoretic deposition method
• Estimation Equation for Sieving Rate Based on the Model for Undersized Particles Passing through Vibrated Particle Bed
• Quantitative Evaluation of Relationship between Coke Strength and Pore Structure
• Quantification of the Existence Ratio of Non-Adhesion Grain Boundaries and Factors Governing the Strength of Coke Containing Low-Quality Coal
• Numerical Analysis of 3-D Microstructure of Coke Using Micro X-ray CT
• Heterogeneous nucleation and growth mechanism on hydrophilic and hydrophobic surface
• Numerical Analysis of 3-D Microstructure of Coke Using Micro X-ray CT

もっと見る 閉じる

スポンサーリンク