Simultaneous Three-dimensional Analysis of Gas–Solid Flow in Blast Furnace by Combining Discrete Element Method and Computational Fluid Dynamics
スポンサーリンク
概要
- 論文の詳細を見る
Low reducing agent operation of the blast furnace is an essential method for mitigating CO2 emissions in ironmaking. Because the coke rate is reduced in low reducing agent operation, gas permeability tends to deteriorate. Recently, blast furnaces with inner volume larger than 5000 m3 have become usual not only in Japan, but also in other Asian nations. Under these conditions, detailed information on in-furnace phenomena is required to attain stable operation.In the present study, a combination model using the discrete element method and computational fluid dynamics (DEM-CFD) was introduced to understand the fully three-dimensional in-furnace phenomena in the whole blast furnace. Due to the limitations of computational resources, the number of DEM particles must be reduced when applying DEM to the whole blast furnace. On the other hand, small cells must be used in the continuum model in order to calculate the gas flow in detail. Thus, mutual conversion between the location of particles in DEM and the property of the cells in the continuum model is needed. In this study, a method of converting information on the locations of cluster-approximated particles treated in DEM to continuum cells was proposed. Furthermore, optimization in which cells could be obtained without conversion parameters was performed to avoid losing local information obtained by DEM calculations. Simulations of solid movement and gas flow were successfully carried out with this coupled DEM-CFD model. As a result, it became possible to understand the three-dimensional stress field among particles under gas flow, transient gas flow and pressure distribution caused by charging of the burden materials, as well as solid motion.
著者
-
Ueda Shigeru
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
-
Inoue Ryo
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
-
Ariyama Tatsuro
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
-
Kano Junya
Institute of Multidisciplinary Research for Advanced Materials, Tohoku University
-
Natsui Shungo
Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University
-
Nogami Hiroshi
Department of Chemical Engineering, Ichinoseki National College of Technology
関連論文
- Enhancement of Reactivity of Carbon Iron Ore Composite Using Redox Reaction of Iron Oxide Powder
- Influences of Physical Properties of Particle in Discrete Element Method on Descending Phenomena and Stress Distribution in Blast Furnace
- Transient Behavior of Burden Descending and Influence of Cohesive Zone Shape on Solid Flow and Stress Distribution in Blast Furnace by Discrete Element Method
- Effect of Mechanical Milling on Carbothermic Reduction of Magnesia
- Simulation of Mass Flow Rate of Particles Discharged from Hopper by Particle Element Method
- Simultaneous Three-dimensional Analysis of Gas–Solid Flow in Blast Furnace by Combining Discrete Element Method and Computational Fluid Dynamics
- Dynamic Analysis of Gas and Solid Flows in Blast Furnace with Shaft Gas Injection by Hybrid Model of DEM-CFD
- Relation between mechanochemical dechlorination rate of polyvinyl chloride and mill power consumption
- Mechanochemical dechlorination of polyvinyl chloride with calcium sulfates
- Reduction of Indium(III) Oxide to Indium through Mechanochemical Route
- Preparation of GaN Powder by Mechanochemical Treatment of Gallium under Ammonia Gas Environment
- 高炉冷間モデル実験との比較に基づく離散要素法パラメーターの感度解析
- Quantitative Analysis of Total and Insoluble Elements and Inclusion Composition in Metal by Laser Ablation ICP-MS Method
- Cold-model Experiments on Deadman Renewal Rate Due to Sink-Float Motion of Hearth Coke Bed
- Numerical Analysis of Static Holdup of Fine Particles in Blast Furnace
- Numerical Analysis on Blast Furnace Performance under Operation with Top Gas Recycling and Carbon Composite Agglomerates Charging
- Numerical Analysis on Blast Furnace Performance under Operation with Waste Plastics Injection and Top Gas Recycling
- Numerical Analysis on Injection of Hydrogen Bearing Materials into Blast Furnace
- Numerical Analysis on Charging Carbon Composite Agglomerates into Blast Furnace
- Numerical Analysis on Top Gas Recycling in Blast Furnace with Carbon Composite Agglomerates Charging
- Numerical Evaluation on Blast Furnace Performance under Operation with Carbon Composite Agglomerates Charging
- Numerical Analysis on Effects of Charging Carbon Composite Agglomerates on Blast Furnace Operation
- Mathematical Model of Over-micron and Nano-scale Powders Accumulation in a Coke Fixed-Bed Filter
- Numerical Simulation of the Moving Bed Furnace for Iron Scrap Melting
- Numerical Simulation of the Moving Bed Furnace for Iron Scrap Melting
- Three-dimensional Multiphase Mathematical Modeling of the Blast Furnace Based on the Multifluid Model
- Numerical Analysis of Multiple Injection of Pulverized Coal, Prereduced Iron Ore and Flux with Oxygen Enrichment to the Blast Furnace
- Transient Mathematical Model of Blast Furnace Based on Multi-fluid Concept, with Application to High PCI Operation
- Numerical study on natural gas injection to the blast furnace
- Transient Mathematical modeling of Blast Furnace based on multi-fluid concept
- Thermodynamics on Control of Inclusions Composition in Ultra-clean Steels
- Dissolution Behavior and Stabilization of Fluorine in Secondary Refining Slags
- Influence of Gypsum Addition and Hydrothermal Treatment on Dissolution Behavior of Fluorine in Hot Metal Pretreatment Slags
- Mechanism of Dephosphorization with CaO-SiO_2-Fe_tO Slags Containing Mesoscopic Scale 2CaO・SiO_2 Particles
- Behavior of Phosphorous Transfer from CaO-Fe_tO-P_2O_5(-SiO_2) Slag to CaO Particles
- Analysis of transient blast furnace behavior by using a 3-D mathematical model
- Three-dimensional blast furnace mathematical modeling based on multi-fluid theory
- Fluorine-containing Mineral Phases in Ironmaking and Steelmaking Slags and Their Solubilities in Aqueous Solution
- Grinding of talc particulates by a high-speed rotor mixer
- Analysis on Material and Energy Balances of Ironmaking Systems on Blast Furnace Operations with Metallic Charging, Top Gas Recycling and Natural Gas Injection
- Numerical Investigation on Effects of Deadman Structure and Powder Properties on Gas and Powder Flows in Lower Part of Blast Furnace
- Computational Investigation of Scrap Charging to the Blast Furnace
- Analysis of Actual Blast Furnace Operations and Evaluation of Static Liquid Holdup Effects by the Four Fluid Model
- Prediction of Blast Furnace Performance with Top Gas Recycling
- A Mathematical Model for Blast Furnace Reaction Analysis Based on the Four Fluid Model
- A Mathematical Model of Four Phase Motion and Heat Transfer in the Blast Furnace
- Distributions of Sn, Sb, and Bi between Ag-Pb Alloy and PbO Based Melt at 1273K
- Characteristics of Solid Flow and Stress Distribution Including Asymmetric Phenomena in Blast Furnace Analyzed by Discrete Element Method
- Optimization of Physical Parameters of Discrete Element Method for Blast Furnace and Its Application to the Analysis on Solid Motion around Raceway
- Improvement of Reactivity of Carbon Iron Ore Composite with Biomass Char for Blast Furnace
- Reaction Model and Reduction Behavior of Carbon Iron Ore Composite in Blast Furnace
- Infrared Emission Spectra of CaF_2-CaO-SiO_2 Melt
- Phasediagram study on the Al_2O_3-CaO-TiO_2 system
- Synthesis of Niobium Carbides from Ferroniobium by Mechanochemical Method
- Phosphorous Partition between 2CaO・SiO_2 Particles and CaO-SiO_2-Fe_tO Slags
- Thermodynamics of Zirconium Deoxidation Equilibrium in Liquid Iron by EMF Measurements
- Size Distribution of Deoxidation Products with Ti, Pr and Ti/Pr in Fe-10mass%Ni Alloy
- Grain-growth-inhibiting Effects of TiC and ZrC Precipitates in Fe-0.15-0.30mass%C Alloy
- Effect of TiN Precipitates on Austenite Grain Size in Fe-1.5%Mn-0.12%Ti-Si(
- Tungsten Extraction from Scheelite by means of Mechanochemistry and Heating
- Effect of Mechanical Milling on Carbothermic Reduction of Magnesia
- Estimation of Extraction Rate of Yttrium from Fluorescent Powder by Ball Milling
- Estimation of Size Reduction Rate of Gibbsite in Tumbling Mills with Different Diameters by Computer Simulation
- Correlation of Size Reduction Rate of Inorganic Materials with Impact Energy of Balls in Planetary Ball Milling
- Influences of Physical Properties of Particle in Discrete Element Method on Descending Phenomena and Stress Distribution in Blast Furnace
- Transient Behavior of Burden Descending and Influence of Cohesive Zone Shape on Solid Flow and Stress Distribution in Blast Furnace by Discrete Element Method
- Recent Progress and Future Perspective on Mathematical Modeling of Blast Furnace
- Enhancement of Reactivity of Carbon Iron Ore Composite Using Redox Reaction of Iron Oxide Powder
- Influence of Blast Furnace Inner Volume on Solid Flow and Stress Distribution by Three Dimensional Discrete Element Method
- Dynamic Analysis of Gas and Solid Flows in Blast Furnace with Shaft Gas Injection by Hybrid Model of DEM-CFD
- Analysis of Granules Behavior in Continuous Drum Mixer by DEM
- Numerical Simulation Model for Granulation Kinetics of Iron Ores
- Simultaneous Determination of the Composition and Size of Oxide Particles in Solid Materials by Laser Ablation-Inductively Coupled Plasma Mass Spectrometry
- Analysis of abrasion mechanism of grinding media in a planetary mill with DEM simulation
- MECHANOCHEMICAL DECHLORINATION OF PVC
- Zeolite Synthesis from Fly Ash : Current Processes and their Benefits and Drawbacks
- Correlation between the Grinding Rate Constant and the Impact Energy of Beads during Wet Bead Milling
- Effect of the friction coefficient in the discrete element method simulation on media motion in a wet bead mill
- Application of the DEM in Simulation of the Media Motion in a Wet Bead Mill
- Influence of polymer impurity on the mechanochemical dechlorination reaction of polyvinyl chloride
- Dechlorination of polyvinyl chloride by its grinding with KOH and NaOH
- Mechanochemical dechlorination of polyvinyl chloride by co-grinding with various metal oxides
- Reduction in α - Transformation Temperature of Gibbsite and Boehmite by Powder Mixing with Seed
- Effect of additives on dechlorination of PVC by mechanochemical treatment
- Ball mill simulation and powder characteristics of ground talc in various types of mill
- Numerical Simulation Model of the Iron Ore Sintering Process Directly Describing the Agglomeration Phenomenon of Granules in the Packed Bed
- Amorphization of kaolinite and media motion in grinding by a double rotating cylinders mill-a comparison with a tumbling ball mill
- Simulation of Operational Power of Co-Axial Double Rotating Cylinders Mill by Particle Element Method
- Modeling of Iron Ore Sintering Process by Combining Discrete Element Method and Gas-solid Heat Transfer Equiations
- Effect of Heat Wave Propagation on the Structural Changes in the Iron Ore Sintering Bed
- Activity Coefficient of AgO_ in PbO-NaO_ and PbO-CaO Melts at 1273K
- Thermodynamic Properties of Selenium in Ag-Pb Alloy and Lead Oxide Phases at 1273K
- Activity Coefficient of AgO_ in the PbO-SiO_2 Melt at 1273K
- Thermodynamic Study on the Ag-Pb-O System at 1273K
- Simultaneous Three-dimensional Analysis of Gas-Solid Flow in Blast Furnace by Combining Discrete Element Method and Computational Fluid Dynamics
- Penetration Effect of Injected Gas at Shaft Gas Injection in Blast Furnace Analyzed by Hybrid Model of DEM-CFD
- Wettability Model Considering Three-Phase Interfacial Energetics in Particle Method
- 粒子配置を考慮した充填層の熱物質移動解析
- 冷間モデルと離散要素法を用いた竪型乾留炉内粒子の降下挙動解析
- Influence of Physical Properties of Melt on Liquid Dripping in Packed Bed Analyzed by MPS Method