Development of High Strength Fly Ash Glass Ceramics: Influence of Additive on Material Properties
スポンサーリンク
概要
- 論文の詳細を見る
To develop high strength glass ceramics, coal fly ashes produced by a power plant have been melted with addition of CaCO3 and Na2CO3 to obtain glasses. Glass ceramics were produced by reheating selected glass mixtures in the region of 900-1200°C for 1 hour. The properties of the obtained glass ceramics were examined by XRD analysis, SEM observation, and material tests for strength, toughness, hardness, and chemical resistance. It was found that the glass ceramics produced by mixing CaCO3 20% and Na2CO3 20% to the raw material have the best potentiality to serve as structural materials.
著者
-
KAIZU Koichi
Department of Mechanical and System Engineering, University of Hyogo
-
Yoshikawa Akira
Department Of Environmental Engineering Faculty Of Engineering Osaka University
-
Kinoshita Hiroyuki
Department Of Anesthesia Kurashiki Central Hospital
-
NAKAYAMA Yoshihisa
Miyazaki Prefecture Industrial Technical Center
-
Ogawa Shinya
Department Of Applied Biological Chemistry Graduate School Of Agricultural And Life Sciences The University Of Tokyo
-
IKEDA Kiyohiko
Department of Mechanical systems Engineering, University of Miyazaki
-
KIM Hyung-Sun
School of Materials Engineering, Inha University
-
OGAWA Shinya
Department of Mechanical Systems Engineering, University of Miyazaki
-
KAIZU Koichi
Department of Mechanical and System Engineering, Graduate School of Engineering, University of Hyogo
-
IKEDA Kiyohiko
Department of Mechanical Systems Engineering University of Miyazaki
関連論文
- Severe Duodenal Hemorrhage Induced by Lugols Solution Administered for Thyroid Crisis Treatment
- Transient phlebitis induced by a bolus injection of propofol
- Nutritional Effects of γ-Glutamyl Carboxylase Gene Polymorphism on the Correlation between the Vitamin K Status and γ-Carboxylation of Osteocalcin in Young Males
- Analysis Method of Friction Torque and Weld Interface Temperature during Friction Process of Steel Friction Welding
- The Role of Endothelium-Derived Nitric Oxide in Relaxations to Levcromakalim in the Rat Aorta
- A case of Pagetoid carcinoma confined to the nipple
- Surgical Criteria for Nissen Fundoplication and Gastrostomy in Gastroesophageal Reflux Disease and Surgical Treatment for Neurologically Impaired Children
- Plane Elastic Behavior and Stress Intensity Factor for an Inhomogeneous Slab with a Griffith Crack
- Effects of halothane and isoflurane on acetylcholine-induced, endothelium-dependent vasodilation in perfused rat mesenteric arterial beds
- The Role of Oxygen-Derived Free Radicals in Augmented Relaxations to Levcromakalim in the Aorta From Hypertensive Rats
- Pharmacological Significance of the Blocking Action of the Intravenous General Anesthetic Propofol on the Slow Component of Cardiac Delayed Rectifier K^+ Current
- Dynamic Behavior of Thick Plates Due to Oblique Impact : Numerical Analysis of Three-Dimensional Stress Waves in an Elastic/Viscoplastic Body
- A CASE OF SUBMANDIBULAR HEMANGIOMA WITH PHLEBOLITH
- Output Feedback Control of Multirate Sampled Systems with an Adaptive Output Estimator and Its Application to a Liquid Level Process Control
- 529 Experimental and Numerical Simulations of the Riveting Process by Upset Forging
- Leakage from a nonelectric disposable pump
- Benzoyl peroxide : a cause of skin injury in Japan?
- Magnetic Separation of Aerosol Particles from Air Flow
- EFFECTS OF Ca^-ANTAGONISTS ON THE TRANSIENT INWARD CURRENT IN GUINEA-PIG PAPILLARY MUSCLE : Arrhythmias (I), Electrophysiology (II) : III : 48 Annual Scientific Meeting, Japanese Circulation Society
- Acremolactone A, a Novel Herbicidal Epoxydihydropyranyl γ-Lactone from Acremonium roseum I4267
- Effect of Friction Welding Condition on Joining Phenomena and Tensile Strength of Friction Welded joint between Pure Copper and Low Carbon Steel
- Serotonin syndrome induced by dextromethorphan (Medicon) administrated at the conventional dose
- Operating table failure and suggested safety precautions
- Production of High-Strength Glass-Ceramics from Industrial Wastes Using Phase Equilibrium Diagram of CaO-Al2O2-SiO2 System
- Numerical Analysis of Two-Dimensional Stress Waves in Transverse Isotropic Cylinder due to Longitudinal Impact
- The effect of airway narrowing and dead space on the shape of the capnogram
- Development of High Strength Fly Ash Glass-ceramics by Concrete Sludge Addition
- Optimized Method for Determining Free L-Cysteine in Rat Plasma by High-Performance Liquid Chromatography with the 4-Aminosulfonyl-7-fluoro-2,1,3-benzoxadiazole Conversion Reagent
- Effects of oxidative stress on vascular function, and the role of anesthetics
- Joint Strength and Their Improvement of Type 5052 Aluminum Alloy Autocompleting Friction Welded Joint
- Development of High Strength Fly Ash Glass Ceramics: Influence of Additive on Material Properties
- The Fatigue Crack Growth Behavior in Thermally Tempered Glass by the Growth of Indentation-Induced Microcracks
- Production and Material Properties of Ceramic from Waste Glass Fiber Reinforced Plastic
- Impact Fracture Analysis of Thermally Tempered Glass by the Extended Distinct Element Method