Effect of Blade Angle on Crystallinity Change in a Mechanical Impact Mill
スポンサーリンク
概要
- 論文の詳細を見る
Experimental and numerical studies have been conducted on the effect of rotor blades in a mechanical impact mill. The flow fields and particle trajectories around the rotor were calculated using the CFD software, Fluent. Calcium carbonate and β-cyclodextrin particles pulverized in the mill with various blade angles were characterized by particle size distribution analyses and X-ray diffraction (XRD). The optimum blade angle for changing crystalline property of the product is different from that required for size reduction. Fine particles are produced when the blades are inclined forwards at an angle of 30 degrees while the blades inclined at 15 degrees promote the efficient change in crystallinity of the product. From the CFD simulations, size reduction is related to the amount of normal impact energy of particles colliding with the blade and stator walls when the particles pass through the pulverizing zone. The change in the crystallinity of particles is related to the amount of tangential impact energy applied to the particles in the pulverizing zone.
- 社団法人 化学工学会の論文
- 2004-10-01
著者
-
Yoshida Hideto
Department Of Chemical Engineering Graduate School Of Engineering Hiroshima University
-
AKIYAMA Satoshi
Research Center for Production & Technology, Nisshin Seifun Group Inc.
-
KOZAWA Kazumi
Research Center for Production & Technology, Nisshin Seifun Group Inc.
-
Kozawa Kazumi
Research Center For Production & Technology Nisshin Seifun Group Inc.
-
Akiyama Satoshi
Research Center For Production & Technology Nisshin Seifun Group Inc.
関連論文
- Effect of Inlet Duct Shape on Particle Separation Performance of Cyclone Separator
- Particle size measurement of standard reference particle candidates and theoretical estimation of uncertainty region
- Enhancement of the Classification Performance of Electrical Field-Flow Fractionation Using Horizontal Electrophoresis
- Influence of inlet flow rate, pH, and beads mill operating condition on separation performance of sub-micron particles by electrical hydrocyclone
- Rapid and simultaneous determination of multi-element abundances and U-Pb age for zircon crystal using UV laser ablation ICP-MS technique: critical evaluation of the technique with 91500 zircon standard
- Particle size measurement of standard reference particle candidates with improved size measurement devices
- Effects of initial slurry concentration distribution on the particle size distribution measured with a sedimentation balance method
- Synthesis of indium tin oxide powder by solid-phase reaction with microwave heating
- Continuous fine particle classification by water elutriator with applied electro-potential
- Utilization of NaCl for phillipsite synthesis from fly ash by hydrothermal treatment with microwave heating
- Classification of Particles Dispersed by Bead Milling Using Electrical Field-Flow Fractionation
- Effect of Multi-Inlet Flow on Particle Classification Performance of Hydro-Cyclones and New Estimating Equation
- Effects of microwave irradiation on the crystalline phase of zeolite synthesized from fly ash by hydrothermal treatment
- Investigation about Data Reduction and Sedimentation Distance of Sedimentation Balance Method
- Phillipsite synthesis from fly ash prepared by hydrothermal treatment with microwave heating
- Effect of apex cone height on particle classification performance of a cyclone separator
- Particle size measurement with an improved sedimentation balance method and microscopic method together with computer simulation of necessary sample size
- Particle Separation with a Hydro-Cyclone Separator in a Wet Limestone Gypsum FGD Process
- Separation of Unburned Carbon in Fly Ash Particles Using Special Louver Separator
- Classification of Particles Dispersed by Bead Milling Using Electrical Field-Flow Fractionation
- Meteor Storm Activity and Average Size of Meteoroids for the 2001 Leonids by FM Broadcasting Radio Observation
- Effect of Blade Angle on Crystallinity Change in a Mechanical Impact Mill
- Comparison of separation performance between single and two inlets hydrocyclones
- Theoretical calculation of fundamental uncertainty region based on the maximum and/or the minimum size in the preparation of standard reference particles for particle size measurement
- Enhancement of the Classification Performance of Electrical Field-Flow Fractionation Using Horizontal Electrophoresis
- Classification of particles by centrifugal separator and analysis of the fluid behavior
- Improvement of grinding and classifying performance using a closed-circuit system
- Environmental Transmission Electron Microscopy Observations of Swinging and Rotational Growth of Carbon Nanotubes
- Separation of Unburned Carbon in Fly Ash Particles Using Special Louver Separator
- Carbon Beads on Semiconductor Nanowires
- Size classification of submicron powder by air cyclone and three-dimensional analysis.
- The effect of initial parameters on particle size distribution inverted using the laser diffraction technique and a non-linear iterative method
- Theoretical calculation of uncertainty region based on the general size distribution in the preparation of standard reference particles for particle size measurement