リン銅ろう合金の腐食性に関する研究
スポンサーリンク
概要
- 論文の詳細を見る
The corrosion properties and the mechanical properties of brazing alloy and brazed butt joints are equally important problems that have to be made clear. In brazing, the joints are jointed with different metals to a base metal. Consequently, the corrosion properties of a brazed joint become a very important thing. It is said that the corrosion properties of copper-phosphorus brazed joints are good. However, very little is definitely known about these properties through reasearch. In this study, the corrosion properties of a copper-phosphorus brazing alloy and a brazed joint with the same alloys are examined both in a normal chemical solution and in an ammonium sulfid gas atomosphere. The results obtained are as follows : 1) The corrosion in copper-hosphorus brazing alloys increases in proportion to the amount of phosphorus added to the brazing alloys. (in roome temperature) When oxygen (30cc/min.) is added to the corrosion atmosphere ((NH_4)_2S-Gas), the corrosion rate increased ten times. Also when the temperature of the test chamber is increased to 70℃ the corrosion rate becomes five or seven times greater than the room temperature. Two cylindrical copper brazed butt joints, joined together by a copper-phsphorus brazing alloy, were placed in a test chamber atmosphere filled with (NH_4)_2S gas. The brazed joints were attached to the wall of the chamber and a weight (3Kg/(mm)^2) was hung from the free side of the brazed joint. This lasted for a period of 100 days. At the end of the 100 days, it was found that the outlayer surfaces of the two cylindrical copper brazed butt joints, attached directly to the phosphorus brazing alloy, were beginning to corrode. 2) The corrosion rate of a copper-phosphours brazing alloy in a chemical solution of HNO_3 is the fastest. After this solution the following chemical solutions in this order have the fastest corrosion rate, namely chemical solution of NH_4OH; (NH_4)_2S; HCl and H_2SO_4. Aside from the corrosion effect of HCl and H_2SO_4 solution s an pitting corrosion was also observed on the brazing alloy surface. This pitting corrosion was found to be in the α-phase. 3) Two cylindrical copper brazed butt joints, joined together as above by a phosphorus brazing alloy, were placed in separate chemical solutions of HCl, NHO_3 and NH_4OH for 30 days. After 30 days the cylindrical joints were taken out of each of these solutions and the strength of each was tested by a tension test. It was found that the cylindrical brazed joint in the chemical solution of NH_4OH was the weakest followed by joints in HCl and NHO_3 chemical solutions respectively. The brazed joint was 1/3 dgree weaker than it was prior to placing in that solution.
- 社団法人溶接学会の論文
- 1973-08-25
著者
関連論文
- 海外出張報告 LOET2007学会報告
- 連続無酸化雰囲気炉による工業用純チタンのろう付
- チタン系積層ろう材による工業用純チタンの接合
- ろう付の材料表面による影響 (特集 機能性材料における表面処理技術の現状と展望)
- 技術解説 工業用純Tiと純Niのマイクロスポットろう付
- Ni 添加 BNi-5 粉末ろう材によるステンレス鋼の広間隙ろう付
- 353 Ni-Cr-Si-P系ろう材を用いたステンレス鋼のろう付
- 350 ろう付によるチタン製熱交換器の製作
- 第6回ろう付,高温接合国際会議に参加して
- 319 スポットろう付により作製した工業用純Ti/Ni接合体の強度と接合部組織
- チタンのマイクロスポットろう付
- マグネシウム合金板のマイクロスポットろう付
- AWS (American Welding Society)のAnnual Meetingに参加して
- 225 Sn-(Ag, Bi, Zn)共晶はんだ合金の組織と硬さ
- 440 純Auと純Tiとの界面反応
- 最近のアルミニウムろう付技術とその応用
- Al-Li合金のろう接
- Ni系ろう材による広間隙ろう付
- 鉛を含まない共晶はんだ合金の組織変化
- 鉛を含まないSn-Zn共晶はんだに関する研究
- カドミニウム含有銀ろうを検証する (特集 最近のろう付技術の動向)
- ろう付関係JIS国際整合化の動き (フォーラム/最近のろう付)
- AlN/Cu間の反応層成長に対する合金添加元素の影響 (異種材料間の界面現象)
- SiO2上に蒸着したW薄膜の組織と電気抵抗に及ぼす熱処理の影響
- 加工を施したCu-Ti合金の時効挙動
- サファイヤとインコネルのろう付
- 417 Ni系ろう材のNi基耐熱合金と軟鋼に対するろう接性に関する研究
- 405 アルミナとニッケル合金との接合
- Ni系ろう材のNi基合金及び軟鋼に対するろう接性
- Ni-Cr-Si-B系ろう材を用いたインコネル600と軟鋼の接合
- 溶融Ni-Si-B系合金と固体ステンレス鋼(SUS304)との界面反応
- Wetting balance法を用いたPb-Sn soft solderのCuに対するぬれ性について
- アモルファスろう材によるろう接 (接合技術)
- 超塑性鍛造による腕時計裏蓋成形への有限要素法の適用-チタン合金製腕時計ケースの開発 III-
- 230 溶融錫と固体銅界面の合金層成長について
- 溶融錫と固体銅界面の合金層成長について
- Ni系ろう材によるSUS304鋼のろう接性について
- 132 溶融錫への固体銅の溶解現象に関する研究 : 強制対流下での試料寸法の影響
- 131 溶融錫への固体銅の溶解現象に関する研究 : 自然対流下での試料寸法の影響
- 231 静的条件下における溶融錫鉛合金中への固体銅の溶解現象
- 溶融 Al-Si-Mg 合金中における固体 Al の溶解現象
- 347 溶融Sn中への個体Cuの溶解現象(第2報) : 動的条件下における溶解
- 346 溶融Sn中への個体Cuの溶解現象(第1報) : 静的条件下における溶解
- 302 溶融Al-Si-Mg合金中における固体Alの溶解現象
- リン銅ろう材のぬれ性について
- 51 Cu-P系ろう材によるろう付接合部の強さ
- 256 リン銅ろう材へのSm添加による影響について
- 銅及び銅合金板上のリン銅ろうの拡がり性
- 403 銅メッキ鋼板におけるリン銅ろう材のろう接性について
- リン銅ろう合金の腐食性に関する研究
- 247 リン銅ろう材のBrazing Sheetに関する研究
- CVDにより作成したSiC繊維と溶融Al-Ti,Al-Zr合金との界面反応
- CVD法により作製したSiC繊維と溶融アルミニウム合金との界面反応
- 343 Cu-Snろう材のろう接性について
- Wetting balance 法をいた Pb-Sn soft solder の Cu に対するぬれ性について
- 342 Cu-Ni-Su-P系アモルファスろう材について
- 電流負荷がSn-Cu-In系はんだ付部の組織に及ぼす影響
- 積層型ろう材を用いたCP-Tiとステンレス鋼のろう付
- 426 ニッケル系アモルファスろう材のろう特性
- 新しいろう材-アモルファスろう
- 407 リン銅ろう合金の腐食的性質